6 October 2020 in Metal and Casting of Ukraine
LULlc (Dnipro Sheffield Refractories Ukraine
Llc (Dnipro Sheffield Refractories Ukraine
+1
Study of the processes of subsurface crack formation in a rhombic varietal billet during production in the conditions of a metallurgical micro-mill
15 June 2024 in International Journal of Metalcasting
1 November 2019 in Metal and Casting of Ukraine
DODnipro Sheffield Refractoris Ukraine Ojsc
Dnipro Sheffield Refractoris Ukraine Ojsc
The most effective method for studying the dynamics of solidification of various kinds of ingots is physical modeling. A physical model that simulates a cross section of a continuously cast billet was created.
1 January 2020 in Metal and Casting of Ukraine
Investigation of internal defects formation reasons in copper billet obtained at rotary continuous casting machine (CCM)
1 January 2024 in Metal and Casting of Ukraine
One of the key elements defining the technical level and operational capabilities of continuous casting machines (CCM) is the complex of physico-mechanical properties of copper or copper alloys used in its production. The paper provides a comprehensive assessment of the possibility of obtaining high-quality copper plates for CCBC crystallizers based on domestic technologies and equipment using refined copper. Special attention was paid to the need to optimize the chemical composition of the copper alloy within a narrower range of chemical element values. The analysis of the research shows that currently used copper alloys for CCM crystallizer manufacturing have a wide range of fluctuations in the main operational properties, namely thermal conductivity (260-390 W/(m·K)) and solidification temperature (250-700 °C). However, most of the alloys used have narrower fluctuation limits for acceptable values, constituting 340-390 W/(m·K) for thermal conductivity and 300-370 °C for solidification temperature, significantly depending on the impurity content in the copper alloy. Generalizing graphical dependencies, it should be assumed that the rational phosphorus content in the alloy is in the range of 40-120 ppm. In this case, the thermal conductivity of the alloy will be in the range of 370-400 W/(m·K), the solidification temperature will be 410-440 °C, and the recrystallization start temperature will be 370-400 °C. Moreover, such a phosphorus content interval is technologically feasible to maintain during billet casting. It is also shown that normalization annealing after cold deformation in the temperature range of 320-350 °C is capable of increasing the thermal conductivity of the alloy by 1-2 %. As a result of the conducted research, optimal limits of phosphorus content in fire-refined copper were established, ensuring the level of its physico-mechanical properties not lower than the indicators characteristic of alloys obtained from cathode copper. However, besides phosphorus, other alloy impurities, the content of which differs from the values characteristic of alloys obtained from cathode copper, may affect the properties of the material made from refined copper. Therefore, further research will focus on studying their complex impact on the physico-mechanical properties of refined alloys.
1 January 2023 in Metal and Casting of Ukraine
Проведено експериментальні серії розливання сталі для визначення впливу методу безперервного розливання на частоту формування дефектів сортової заготовки. При цьому виробництво квадратних заготовок перетином 125х125 мм здійснювалось на шестиструмковій сортовій машині безперервного лиття заготовок (МБЛЗ) зі швидкостями розливання 2,8-4,3 м/хв. У процесі дослідження спочатку була розлита серія з 5 плавок сталі 60 (Ст60) відкритим струменем. Після цього, з використанням тих же гільз кристалізаторів, послідовно розливали закритим струменем 5 плавок сталі 40Х. Шляхом промислового експерименту було визначено, що в результаті безперервного розливання сталі відкритим струменем кількість ромбічності сортової заготовки становить 4,5 %. Зокрема, у випадку застосування технології розливання металу закритим струменем дефектів геометричної форми заготовок не виявлено. Використання системи «стопор-моноблок» — «стакан-дозатор» — «занурений стакан» дозволяє більш точно й вчасно регулювати витрату металу під час розливання в автоматичному режимі, не змінюючи швидкість витягування заготовки. При цьому забезпечується збереження рівня металевого розплаву в кристалізаторі, що найбільш точно враховує особливості формування скоринки заготовки по всій довжині гільзи при поточній швидкості лиття. Відсутність необхідності регулювання швидкості розливання рівнем металу в промківші дозволяє підтримувати в ньому оптимальну кількість розплаву, що стабілізує температуру розливання. Підведення струменя сталі за допомогою зануреного стакана під рівень металу в кристалізаторі запобігає бурлінню на межі розподілу фаз, а можливість істотного збільшення внутрішнього діаметра стакана-дозатора (у порівнянні з вільним витіканням) у кілька разів знижує швидкість його заростання відкладеннями корунду. Крім цього, розливання закритим струменем дозволяє застосовувати спеціальні шлакоутворюючі суміші, які забезпечують покращення якості поверхні заготовки. Додатково підвищити якість безперервнолитих зливків можливо за рахунок застосування електромагнітного перемішування рідкої сталі.