18 December 2025 in Мінеральні ресурси України
This paper presents the results of comprehensive studies of a biopolymer gravel composite developed on the basis of polylactic acid (PLA) and natural gravel for use in block filters of hydrogeological wells. The main focus is on studying the mechanical and hydraulic properties of the material that ensure its operational reliability and environmental safety. The influence of PLA content on compressive strength, resistance to the influence of the aquatic environment, porosity, permeability, and filtration coefficient was analyzed. Experimental composite samples were made by hot pressing with different polymer mass fractions and gravel fractions. It was found that increasing the PLA content to 16% significantly increases the strength of the material, but is accompanied by a decrease in porosity and permeability.With a low polymer content (4–12%), the composite demonstrates an optimal balance of mechanical strength and filtration capacity. Studies have shown that biopolymer gravel composite retains structural stability and resistance to water saturation. At the same time, during prolonged exposure to an aqueous environment, a gradual change in filtration characteristics is observed, caused by the destruction of PLA.The findings confirm the feasibility of using PLA–gravel composites as environmentally safe and technologically effective materials for well filtration systems designed for groundwater purification and exploitation. The developed approaches form a scientific basis for further optimization of the composite composition and the production technology of new-generation block biopolymer filters that combine mechanical strength, hydraulic stability, and biodegradability.
30 August 2025 in Neft i Gaz
This work considers maintaining the required density of drilling mud using weighting agents such as barium sulfate (BaSO4) as a key factor in ensuring wellbore stability and preventing complications during drilling. However, the introduction of barite into the drilling fluid can cause contamination of productive formations, reducing their permeability and productivity. Penetration of solid barite particles into the pore space leads to clogging of pores and filtration channels, which often becomes irreversible without specialized cleaning methods. To reduce the risk of contamination, it is necessary to optimize the composition of the drill-ing fluid and carefully control drilling parameters. The use of crystallization inhibitors, stabilizers, and polymer additives helps reduce barite sedimentation and decrease its adhesion to pore walls. This significantly lowers the likelihood of damage to productive intervals. In cases of existing contamination, restorative technologies are applied. Mechanical cleaning, including high-pressure well flushing, may be effective for surface-level clogging but has limited effectiveness for deep particle penetration. A more promising approach is the use of chelating agents capable of binding barium ions and breaking down barite deposits. The effectiveness of these reagents depends on the physical and chemical characteristics of the reservoir. An alternative solution involves specialized solvents designed for selective dissolution of barite in the pore space. Their application requires engineering justification and laboratory verifica-tion. A comprehensive approach, including optimization of the drilling fluid composition, control of technological parameters, and timely application of chemical reagents, helps maintain formation productivity and reduce operational costs during well drilling.
15 December 2024 in Neft i Gaz
SESh. Yessenov Caspian State University of Technologies and Engineering
Sh. Yessenov Caspian State University of Technologies and Engineering
TKTASHKENT STATE TECHNICAL UNIVERSITY NAMED AFTER I. KARIMOV
TASHKENT STATE TECHNICAL UNIVERSITY NAMED AFTER I. KARIMOV
+3
This article presents an analysis of the effectiveness of polymer flooding technology at the Zapad site. The main purpose of the study was to evaluate the effect of injection of a polymer solution on increasing the oil recovery coefficient (ORC) and reducing the water content of products. During the experiment, a polymer solution based on polyacrylamide was used, which was injected into a formation with low permeability. To assess the effectiveness, changes in the flow rate of liquid, oil and water were monitored, as well as an analysis of pressure dynamics in wells. The results of the study showed that the injection of a polymer solution made it possible to significantly increase the oil recovery of the reservoir, increasing the ORC by 3.8% compared with traditional flooding methods. It was also revealed a decrease in the water content of products by 9.3% due to an improvement in the distribution of fluid flows in the reservoir. These results confirm the expediency of using polymer flooding to increase the efficiency of mining in areas with similar geological and physical conditions. The conducted research can serve as a basis for optimizing field development schemes and the introduction of new technologies to enhance oil recovery at other facilities.
15 December 2024 in Neft i Gaz
SESh. Yessenov Caspian State University of Technologies and Engineering
Sh. Yessenov Caspian State University of Technologies and Engineering
ZUZhangir Khan West Kazakhstan Agrarian Technical University
Zhangir Khan West Kazakhstan Agrarian Technical University
+3
As part of the implementation of a comprehensive development project, new impact technologies were created and introduced initially at the experimental sites in order to increase the efficiency of hot water injection to maintain reservoir pressure and reservoir temperature, intensify the development process, increase the current and final ORC: stepwise thermal flooding (STF), figured flooding (FF), separate development of low-yield (refineries) and highly productive (HPZ) zones. The introduction of these technologies at the field contributed to an increase in the coverage of the process of displacement of poorly drained oil reserves, stabilization of oil withdrawals and provided additional oil production, which takes into account the efficiency of hot water injection. The upcoming geological, technological and production works of many oil fields depend on the results of water samples from the wellhead with the flow rate of the extracted liquid. Therefore, determining the exact percentage of water in the production of wells is one of the main goals. Poor quality of well testing data may not be better than their complete absence, especially for specialists in field development planning or production management. The article considers a diverse sampler, describes its role as an addition to multiphase flowmeters, which allows to obtain fluid samples without traditional separators.
30 October 2024 in Neft i Gaz
SGS. Utebaev Atyrau University of Oil and Gas
S. Utebaev Atyrau University of Oil and Gas
SES. Yessenov Caspian State University of Technologies and Engineering
S. Yessenov Caspian State University of Technologies and Engineering
+5
Polymer flooding is widely used due to its advantages. The method is well suited for oil recovery at various stages of field development with uneven permeability, different reservoir properties and structure; it is carried out at low reagent flow rates and does not require expensive and complex equipment. The disadvantages of the method, such as decreased stability of poly-mer solutions at high temperatures (thermal destruction) and mineralization of formation fluids, are usually eliminated by careful selection of polymer composition. The article considers the efficiency of polymer flooding technology to determine the de-gree of properties of the reagents used. For this purpose, the reagents were determined, which should be carried out taking into account individual features and the state of development of a particular field. Studies were conducted to determine the dependence of viscosity on polymer concentra-tion, and the viscosity of the polymer solutions were determined for one day. The study found that the iron concentration in the water is below 1 ppm, which is acceptable that oxygen is not present in the water.
30 March 2026 in Mining of Mineral Deposits
Purpose. The work is aimed at determining the efficiency of the technology of equipping the water intake part of a hydrogeological well with an inverse gravel filter and the economic efficiency of performing work using the proposed technology. Methods. The tasks were solved using a comprehensive research method, which included analysis and generalization of geological and technical information, physical modeling, and experimental research and development. Findings. Production tests of the technology of equipping hydrogeological wells with inverse gravel filters has been carried out, which confirmed the effectiveness of the developed and tested technology. The technology of manufacturing inverse gravel filter elements has been tested in production conditions. There has been shown the possibility of using the developed technologies for manufacturing an inverse gravel filter element and transporting an inverse gravel filter along the borehole of hydrogeological wells during their construction with a depth of more than 200 m, using standard drilling technological equipment and tools. Originality. For the first time, there has been substantiated the use of a water-based mineral binder containing an organic polymer – technical gelatin – for the monolithization of loose gravel material in production conditions into a block structure of a gravel filter of a borehole. For the first time, there has been demonstrated the possibility of equipping the water-receiving part of hydrogeological wells, in fine-grained and fine-grained sands, with inverse gravel filters using the proposed technology. Practical implications. As a result of experimental and production tests, there has been confirmed effectiveness of the developed technology for manufacturing inverse gravel filter elements and transporting the inverse gravel filter along the wellbore. During the tests, the following aspects have been determined: costs for manufacturing prototypes of inverse gravel filter elements; costs for equipping the water intake part of a hydrogeological well with inverse gravel filters; well productivity; economic indicators of the technology for equipping hydrogeological wells with filters using the proposed technologies.