1 October 2012 in Revista IBRACON de Estruturas e Materiais
Punching strength is a critical point in the design of flat slabs and due to the lack of a theoretical method capable of explaining this phenomenon, empirical formulations presented by codes of practice are still the most used method to check the bearing capacity of slab-column connections. This paper discusses relevant aspects of the development of flat slabs, the factors that influence the punching resistance of slabs without shear reinforcement and makes comparisons between the experimental results organized in a database with 74 slabs carefully selected with theoretical results using the recommendations of ACI 318, EUROCODE 2 and NBR 6118 and also through the Critical Shear Crack Theory, presented by Muttoni (2008) and incorporated the new fib Model Code (2010).
1 January 2020 in Journal of Materials in Civil Engineering
BNBernardo B. Pompeu Neto
The bond between concrete and steel bars defines the structural behavior of reinforced concrete—each is the complement of the other. The bond allows for the compatibility of strains, transmission of stresses, and good mechanical behavior, with less possibility of the concrete cracking; this can result in the protection of the reinforcement and a higher structural durability. This study investigates (1) the bond behavior between concrete and steel bars, and (2) the development length of steel bars in steel fiber-reinforced concrete (SFRC). For the tests, the bars had diameters of 8 and 12.5 mm with full development lengths ( ), and with reductions of 50% ( ) and 25% ( ). The volume fraction of steel fibers ( ) had values of 0.0%, 0.5%, and 1.5%. In the results, the flexural ultimate loading for SFRC was higher than for nonfiber-reinforced concrete. For samples with a of 1.5%, the bond strength was higher than that found in other concretes, confirming that the use of steel fibers improved the bond between concrete and reinforcement and the effectiveness of the proposed test system.
1 October 2013 in Revista IBRACON de Estruturas e Materiais
Punching shear is a brittle failure mode that may occur in slab-column connections, which may be prevented by using shear reinforcement in the slab-column connection. This paper presents comparisons between experimental results of 36 tests in internal slab-column connections with double- headed shear studs, which are largely used in North America, Europe and Asia, with theoretical results using recommendations presented by ACI 318, NBR6118, Eurocode 2 and also the Critical Shear Crack Theory (CSCT).Considering the database used it is possible to observe that ACI 318 presents conservative trends, whereas NBR 6118 showed a low coefficient of variation, but with a large number of unsafe results. Both Eurocode 2 and CSCT showed satisfactory results with Eurocode 2 presenting slightly higher performance.
1 October 2018 in Revista IBRACON de Estruturas e Materiais
Ribbed slabs have been widely used in buildings due to their many advantages, especially the decrease of concrete below the neutral line. This paper presents an experimental and computational study on ribbed slabs with wide-beam, two one-way slabs and two two-way slabs, with variable depths were tested to evaluate their resistance to punching and shear strength of slabs. Experimental and computational results showed that the wide-beam ribs connection is a critical point in the design of the slabs due to the difference in stiffness in the transition zone. Best results for the ultimate load estimates for ribs were provided by EC 2 (2004), while estimates of ACI 318 (2008) and NBR 6118 (2014) were respectively conservative and unsafe. Test results on slabs also revealed that the Brazilian alternative to analysis ribbed slabs as solid ones failed to give satisfactory results.
1 November 2021 in Practice Periodical on Structural Design and Construction
This study proposes a practical solution for installing anchoring elements on hard or old concrete surfaces to receive tensile forces. For this situation, where the anchorages will be postinstalled, there is often no depth in the concrete base that meets the minimum straight length of standard anchoring. Thus, the use of headed studs or hooked anchor bolts are the most recommended solutions, but the procedure for installing these elements is still the subject of experimental investigations. Then, the technique of postinstallation of headed studs in hardened concrete niches and the use of structural epoxy resin in the new-old concrete interface is presented. Additionally, the influence of the addition of steel fiber on the anchorage studs performance was also evaluated.
1 January 2022 in Revista IBRACON de Estruturas e Materiais
Some normative recommendations are conservative in relation to the shear strength of reinforced concrete beams, not directly considering the longitudinal reinforcement rate. An experimental program containing 8 beams of (100 x 250) mm2 and a length of 1,200 mm was carried out. The concrete compression strength was 20 MPa with and without 1.00% of steel fiber addition, without stirrups and varying the longitudinal reinforcement ratio. Comparisons between experimental failure loads and main design codes estimates were assessed. The results showed that the increase of the longitudinal reinforcement ratio from 0.87% to 2.14% in beams without steel fiber led to an improvement of 59% in shear strength caused by the dowel effect, while the corresponding improvement was of only 22% in fibered concrete beams. A maximum gain of 109% in shear strength was observed with the addition of 1% of steel fibers comparing beams with the same longitudinal reinforcement ratio (1.2%). A significant amount of shear strength was provided by the inclusion of the steel fibers and allowed controlling the propagation of cracks by the effect of stress transfer bridges, transforming the brittle shear mechanism into a ductile flexural one. From this, it is clear the shear benefit of the steel fiber addition when associated to the longitudinal reinforcement and optimal values for this relationship would improve results.