6 October 2017 in The Analyst
This critical review provides an overview of sensitivity-enhancement strategies and a systematic, quantitative analysis of field-effect transistor (IS-FET/BioFET) sensor literature.
18 September 2022 in Advanced Optical Materials
The unique structural transition of VO2 between dielectric and metallic phases has significant potential in optical and electrical applications ranging from volatile switches and neuromorphic computing to smart devices for thermochromic control and radiative cooling. Critical condition for their widespread implementation is scalable deposition method and reduction of the phase transition to near room temperature. Here, a W:VO2 process based on atomic layer deposition (ALD) is presented that enables precise control of W‐doping at the few percent level, resulting in a viable controllable process with sufficient W incorporation into VO2 to reduce the phase transition to room temperature. It is demonstrated that the incorporation of 1.63 at.% W through ALD growth leads to a state‐of‐the‐art phase transition at 32 °C with emissivity contrast between the low‐temperature and high‐temperature phase exceeding 40% in a metasurface‐based radiative cooling device configuration. The process is shown to be viable on 200 mm silicon substrates as well as flexible polyimide films. The full and self‐consistent temperature‐dependent characterization of the W‐doped VO2 using spectroscopic ellipsometry, electrical conductivity, mid‐wave infrared camera, and Fourier transform infrared emissivity, allows for a fully validated material model for the theoretical design of various smart and switchable device applications.
27 March 2023 in npj 2D Materials and Applications
This work demonstrates a large area process for atomically thin 2D semiconductors to unlock the technological upscale required for their commercial uptake. The new atomic layer deposition (ALD) and conversion technique yields large area performance uniformity and tunability. Like graphene, 2D Transition Metal Dichalcogenides (TMDCs) are prone to upscaling challenges limiting their commercial uptake. They are challenging to grow uniformly on large substrates and to transfer on alternative substrates while they often lack in large area electrical performance uniformity. The scalable ALD process of this work enables uniform growth of 2D TMDCs on large area with independent control of layer thickness, stoichiometry and crystallinity while allowing chemical free transfers to application substrates. Field effect transistors (FETs) fabricated on flexible substrates using the process present a field effect mobility of up to 55 cm2/Vs, subthreshold slope down to 80 mV/dec and on/off ratios of 107. In addition, non-volatile memory transistors using ferroelectric FETs (FeFETs) operating at ±5 V with on/off ratio of 107 and a memory window of 3.25 V are demonstrated. These FeFETs demonstrate state-of-the-art performance with multiple state switching, suitable for one-transistor non-volatile memory and for synaptic transistors revealing the applicability of the process to flexible neuromorphic applications.
6 December 2023 in Optical Materials Express
The development of the next generation of optical phase change technologies for integrated photonic and free-space platforms relies on the availability of materials that can be switched repeatedly over large volumes and with low optical losses. In recent years, the antimony-based chalcogenide phase-change material Sb2Se3 has been identified as particularly promising for a number of applications owing to good optical transparency in the near-infrared part of the spectrum and a high refractive index close to silicon. The crystallization temperature of Sb2Se3 of around 460 K allows switching to be achieved at moderate energies using optical or electrical control signals while providing sufficient data retention time for non-volatile storage. Here, we investigate the parameter space for optical switching of films of Sb2Se3 for a range of film thicknesses relevant to optical applications. By identifying optimal switching conditions, we demonstrate endurance of up to 107 cycles at reversible switching rates of 20 kHz. Our work demonstrates that the combination of intrinsic film parameters with pumping conditions is particularly critical for achieving high endurance in optical phase change applications.
13 March 2019 in Scientific Reports
Flexible thermoelectric generators (TEGs) can provide uninterrupted, green energy from body-heat, overcoming bulky battery configurations that limit the wearable-technologies market today. High-throughput production of flexible TEGs is currently dominated by printing techniques, limiting material choices and performance. This work investigates the compatibility of physical vapour deposition (PVD) techniques with a flexible commercial process, roll-to-roll (R2R), for thermoelectric applications. We demonstrate, on a flexible polyimide substrate, a sputtered Bi2Te3/GeTe TEG with Seebeck coefficient (S) of 140 μV/K per pair and output power (P) of 0.4 nW per pair for a 20 °C temperature difference. For the first time, thermoelectric properties of R2R sputtered Bi2Te3 films are reported and we demonstrate the ability to tune the power factor by lowering run times, lending itself to a high-speed low-cost process. To further illustrate this high-rate PVD/R2R compatibility, we fabricate a TEG using Virtual Cathode Deposition (VCD), a novel high deposition rate PVD tool, for the first time. This Bi2Te3/Bi0.5Sb1.5Te3 TEG exhibits S = 250 μV/K per pair and P = 0.2 nW per pair for a 20 °C temperature difference.