Hyungsub Yoon

Hyungsub Yoon

Auto-generated profile, based on publicly available information

Hyungsub Yoon

Institute of Applied Physics “Nello Carrara” (IFAC), Italian National Research Council (CNR), Via Madonna del Piano 10, Sesto Fiorentino, I-50019 Florence, Italy

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 December 2022 in Micromachines
Verified
Journal Article
Open access
PDF file
HYHyungsub Yoon
Hyungsub Yoon
PMPaolo Matteini
Paolo Matteini
BHByungil Hwang
Byungil Hwang
Optimizing the coating conditions for a doctor blading system is important when seeking to improve the performance of Ag nanowire electrodes. In this study, the effect of the blading height and speed on the optical and electrical properties of Ag nanowire electrodes was investigated. Ag nanowires were first spread on a PET substrate using a doctor blade with differing heights at a fixed blading speed. An increase in the blading height resulted in the degradation of the optical transmittance and stronger haze due to the higher probability of Ag nanowire agglomeration arising from the greater wet thickness. When the blading speed was varied, the optical transmittance and haze were unaffected up until 20 mm/s, followed by minor degradation of the optical properties at blading speeds over 25 mm/s. The higher speeds hindered the spread of the Ag nanowire solution, which also increased the probability of Ag nanowire agglomeration. However, this degradation was less serious compared to that observed with a change in the blading height. Therefore, optimizing the blading height was confirmed to be the priority for the production of high-performance transparent Ag nanowire electrodes. Our study thus provides practical guidance for the fabrication of Ag nanowire electrodes using doctor blading systems.

15 March 2025 in Inorganics
Verified
Journal Article
Open access
PDF file
SCSooyong Choi
Sooyong Choi
Sooman LimSooman Lim
Sooman Lim
MHMuhamad Mukhzani Muhamad Hanifah
Muhamad Mukhzani Muhamad Hanifah
PMPaolo Matteini
Paolo Matteini
WYWan Yusmawati Wan Yusoff
Wan Yusmawati Wan Yusoff
BHByungil Hwang
Byungil Hwang
As semiconductor packaging technologies face limitations, through-silicon via (TSV) technology has emerged as a key solution to extending Moore’s law by achieving high-density, high-performance microelectronics. TSV technology enables enhanced wiring density, signal speed, and power efficiency, and offers significant advantages over traditional wire-bonding techniques. However, achieving fine-pitch and high-density interconnects remains a challenge. Solder flip-chip microbumps have demonstrated their potential to improve interconnect reliability and performance. However, the environmental impact of lead-based solders necessitates a shift to lead-free alternatives. This review highlights the transition from Sn-Pb solders to lead-free options, such as Sn-Ag, Sn-Cu, Sn-Ag-Cu, Sn-Zn, and Bi- or In-based alloys, driven by regulatory and environmental considerations. Although lead-free solders address environmental concerns, their higher melting points pose challenges such as thermal stress and chip warping, which affect device reliability. To overcome these challenges, the development of low-melting-point solder alloys has gained momentum. This study examines advancements in low-temperature solder technologies and evaluates their potential for enhancing device reliability by mitigating thermal stress and ensuring long-term stability.

5 September 2022 in Micromachines
Verified
Journal Article
Open access
PDF file
HKHaeji Kim
Haeji Kim
PMPaolo Matteini
Paolo Matteini
BHByungil Hwang
Byungil Hwang
Currently, there is an increasing demand for portable and wearable electronics. This has necessitated the development of stretchable energy storage devices, while simultaneously maintaining performance. Hence, the electrodes and electrolyte materials used in stretchable supercapacitors should be robust under severe mechanical deformation. Polymers are widely used in the fabrication of stretchable supercapacitors. It is not only crucial to choose good polymer candidates with inherent advantages, but it is also important to design suitable polymer materials for both electrodes and electrolytes. This mini-review explains the concept of stretchable supercapacitors, the theoretical background of polymer-based electrodes for supercapacitors, and the fabrication strategies of stretchable electrodes for supercapacitors. Finally, we present the drawbacks and areas that still need to be developed.