Liheng Chen

Liheng Chen

Auto-generated profile, based on publicly available information

Liheng Chen

Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun, China

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 November 2020 in IEEE Access
Verified
Journal Article
Open access
MLMeijiao Liu
Meijiao Liu
YLYanhui Li
Yanhui Li
ALAng Li
Ang Li
QHQi Huo
Qi Huo
NZNing Zhang
Ning Zhang
LCLiheng Chen
Liheng Chen
The Ant Colony Optimization (ACO) is easy to fall into the local optimum and its convergence speed is slow in solving the Travelling Salesman Problem (TSP). Therefore, a Slime Mold-Ant Colony Fusion Algorithm (SMACFA) is proposed in this paper. Firstly, an optimized path is obtained by Slime Mold Algorithm (SMA) for TSP; Then, the high-quality pipelines are selected from the path which is obtained by SMA, and the two ends of the pipelines are as fixed-point pairs; Finally, the fixed-point pairs are directly applied to the ACO by the principle of fixed selection. Hence, the SMACFA with fixed selection of high-quality pipelines is obtained. Through the test of the chn31 in Traveling Salesman Problem Library (TSPLIB), the result of path length was 15381 by SMACFA, and it was improved by 1.42% than ACO. The convergence speed and algorithm time complexity were reduced by 73.55 and 80.25% respectively. What’s more, under the ten data sets of TSPLIB, SMACFA outperformed other algorithms in terms of the path length, convergence speed and algorithm time complexity by comparison experiments. It is fully verified that the performances of SMACFA is superior to others in solving TSP.

29 April 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
SWShaoxin Wang
Shaoxin Wang
LCLiheng Chen
Liheng Chen
Yukun WangYukun Wang
Yukun Wang
ZZZhenping Zhou
Zhenping Zhou
KQKeqi Qi
Keqi Qi
Zhi WangZhi Wang
Zhi Wang
The inertial sensor is the key measurement payload of the technology verification satellite of China’s space gravitational wave detection mission-Taiji Project, which uses capacitive sensors to sense the acceleration disturbance of the test mass under the influence of non-conservative forces in the frequency range of 10 mHz~1 Hz. It is necessary to perform a ground performance evaluation and estimate the working state of the payload in orbit. However, due to the influence of the earth’s gravity and seismic noise, it is impossible to directly evaluate the resolution level of the non-sensitive axis when testing with high-voltage levitation, which leads to incomplete evaluation of the performance of the inertial sensor. In order to implement this part of the test, the sensitive structure is designed and a torsion pendulum facility for performance testing is developed. The experimental results show that the measurement resolution of the non-sensitive axis of the inertial sensor can reach 9.5 × 10−7 m/s2/Hz1/2 under the existing ground environmental conditions and is mainly influenced by the seismic noise during the system measurement. If the inertial sensor enters orbit, the measurement resolution can achieve 3.96 × 10−9 m/s2/Hz1/2, which meets the requirements of the technology verification satellite for a non-sensitive axis. This proposed system also provides a reasonable method for the comprehensive evaluation of inertial sensors in the future.

30 March 2022 in Journal of Thermal Stresses
Verified
Journal Article
Closed access
ZYZhipeng Yuan
Zhipeng Yuan
XMXu Meng
Xu Meng
CLChengliang Li
Chengliang Li
MXMengmeng Xu
Mengmeng Xu
LCLiheng Chen
Liheng Chen
This paper first analyzes the external heat flow of a low-orbit space telescope in different flight attitudes, and determines the position of the heat dissipation surface and the thermal analysis cases. Then, the detailed thermal design of each component of the telescope is completed to reduce the influence of thermal deformation of optical elements and supporting structures caused by temperature changes on the imaging quality of telescope. Especially for the thermal control difficulties of CCD detectors such as large heat generation in a short time and one-dimensional movement in a narrow space, a segmented proprietary cold chain with flexible section is designed to transfer the heat to the radiant cold plate. Finally, the thermal/structure/optical integrated simulation analysis under extreme cases is carried out. It is concluded that the average modulation transfer function (MTF) of the optical system at the cutoff frequency satisfies the design requirement greater than 0.3. The analysis results show that the thermal control system designed in this paper can ensure the optical performance of the telescope, which has important reference significance for the thermal design of other space telescopes.

3 February 2021 in IEEE Access
Verified
Journal Article
Open access
MLMeijiao Liu
Meijiao Liu
YLYanhui Li
Yanhui Li
ALAng Li
Ang Li
QHQi Huo
Qi Huo
NZNing Zhang
Ning Zhang
LCLiheng Chen
Liheng Chen
In the above article [1] , the order of the institution signature 2 and 3 is changed, and the superscript of the author is updated. The institution signature 2 in [1] is changed as the institution signature 3, the institution signature 3 in [1] is changed as the institution signature 2, and the author’s superscript in [1] is updated accordingly.

1 January 2023 in Chinese Optics
Verified
Journal Article
Closed access
RLRen Li-Min
Ren Li-Min
CLChen Li-Heng
Chen Li-Heng
MXMeng Xu
Meng Xu
WZWang Zhi
Wang Zhi

19 December 2024 in Journal of Mechanisms and Robotics
Verified
Journal Article
Closed access
PDF file
PLPeiyi Li
Peiyi Li
HHHasiaoqier Han
Hasiaoqier Han
LJLin Junwei
Lin Junwei
CLChen Liheng
Chen Liheng
QWQingwen Wu
Qingwen Wu
ZXZhenbang Xu
Zhenbang Xu
Offset joints are widely used in robotics, and literature has demonstrated that axial offset joints can expand the workspace. However, the hybrid offset joint, which incorporates offsets in three orthogonal directions (x, y, and z axes), provides a more flexible and comprehensive range of motion compared to traditional axial offset joints. Therefore, a comprehensive understanding of the workspace of hybrid offset joints with three-directional offsets is essential. First, through a parameter model, the interference motion of hybrid offset joints is studied, considering three different directional offsets and obtaining analytical expressions. Next, based on coordinate transformations, the workspace of this joint is investigated, resulting in corresponding theoretical formulas. In addition, the influence of offset amounts in various directions on the joint’s workspace is examined. Finally, the application of hybrid offset joints in parallel manipulators (PMs) is introduced, highlighting their practical engineering value. Through comparative analysis, it is found that lateral offsets on the x- and y-axes adjust the maximum rotation angles, while the z-axis offset expands the rotational range of these joints. Moreover, by increasing the limit rotation angle of the passive joint in a specific direction, the application of hybrid offset joints in PMs can impact the workspace. These findings offer valuable insights for the design of hybrid offset joints and their applications in robotics.