Указаны преимущества карботермического способа вскрытия перовскитового концентрата в сравнении с гидрометаллургическими методами. Отмечены работы, в которых использовался карботермический способ. Даны сведения о существующих способах переработки перовскита, которые не нашли применения в промышленности. Приведены результаты исследования вскрытия титанового сырья на примере искусственно синтезированного перовскита CaO·TiO2. Синтез искусственного перовскита проводили в муфельной печи, при этом смесь оксидов (CaO – 41,2 мас.% и TiO2 – 58,8 мас.%) предварительно перемешивали в течение 15 мин, затем брикетировали в таблетки с использованием стальной пресс-формы диаметром 15 мм на гидравлическом прессе с усилием 147 МПа. Температура синтеза CaTiO3 составляла 1300 °С при времени выдержки 4 ч. Проведены опыты с различным избытком углерода (20 и 30 мас.% от стехиометрически необходимого для восстановления компонентов перовскита). Карботермический процесс вскрытия искусственного перовскита (таблетки массой 4 г) осуществлялся в вакуумной печи с графитовым нагревателем в две стадии: при температуре 1500 °С, времени выдержки 1 ч и остаточном давлении 10,1 кПа в атмосфере аргона на первой стадии и t = 1750 °С, τ = 1 ч, остаточном давлении в камере 1,3 Па – на второй. Продукты реакций изучали рентгенофазовым анализом на дифрактометре «D8 Advance Bruker AXS». Результаты опытов показали практическую возможность извлечения титана и кальция из перовскита карботермическим способом.
19 November 2025 in Transaction Kola Science Centre
The article presents key technological directions of Giredmet aimed at solving the problem of securing raw materials (pure rare-earth and rare metals) for the production of unique alloys. Based on scientific heritage and innovations, the developments encompass: deep hydrometallurgical purification of rare-earth element (REE) oxides; production of individual metals via metallothermic methods and electrolysis; processing of technogenic waste to extract valuable components; smelting a wide range of alloys (high-entropy alloys (HEA), high-temperature shape memory alloys (SMA), pseudo-alloys, metal hydrides, etc.) using vacuum induction melting (VIM), vacuum arc remelting (VAR), and powder metallurgy.
Problem. Calciothermic reduction of zirconium dioxide is one of the promising methods for producing zirconium powders. To reduce the synthesis temperature and modify the product morphology, calcium chloride is often introduced into the charge; however, its influence on phase formation and the final powder characteristics is insufficiently studied. Aim. To investigate the influence of calcium chloride introduced into the charge during the calciothermic reduction of zirconium dioxide on the phase composition, morphology, dispersity, and reactivity of the resulting zirconium powder. Methods. A comparative analysis was performed on two series of samples obtained with and without flux (CaCl2). Chemical composition was determined by arc atomic emission analysis; phase composition – by X-ray diffraction analysis; particle size distribution – by laser diffraction; specific surface area – by the BET method; particle morphology – by scanning electron microscopy; and active zirconium content – by gravimetric method. Results. It was shown that the addition of calcium chloride to the charge by wetting in an alcohol solution increased the specific surface area of the powder from 0.56 m2/g (without CaCl2) to 2.9 m2/g (with CaCl2) while maintaining the average particle size (d50 ~5 μm). However, this was accompanied by the retention of the calcium zirconate (CaZrO3) phase in the product, which was not removed during standard hydrometallurgical processing, leading to an increased residual calcium content (1.10 wt.% vs. 0.05 wt.%) and a decrease in active zirconium content (64.7 % vs. 96.9 %). Conclusions. The obtained results indicate the need to optimise process parameters when using CaCl2 as a flux. The calciothermic method without flux additives made it possible to produce a powder with characteristics comparable to literature data.