Employing centrifugal self-propagating high-temperature synthesis (SHS) metallurgy, complemented by advanced metallurgical processes such as vacuum induction melting (VIM) and vacuum arc remelting (VAR), yielded the alloy formulation denoted as base–2.5Mo–1.5Re–1.5Ta–0.2Ti. This study investigates the effects of various technological modes and additional metallurgical treatments on the alloy's impurity and non-metallic inclusion content, structural characteristics, mechanical behavior under compression, and its oxidation mechanisms and kinetics when exposed to temperatures of 1150 °C for 30 h. With increasing centrifugal acceleration, the proportion of non-metallic inclusions (number of points) drops from 5 to 1–2 points. The best combination mechanical properties, including σucs = 1640 ± 20 MPa, σys = 1518 ± 10 MPa, and residual deformation were observed in alloys processed under conditions of increased gravitational force (g = 50). Within a centrifugal force range of g = 20÷300, the composition of the synthesis products aligned with the theoretical expectations. The total content of impurities is 0.15 ± 0.02 %, with a decrease in gas impurities–oxygen and nitrogen levels reduced to 0.018 % and 0.0011 %, respectively. The structural analysis of the alloys revealed the presence of globular and streaked inclusions of a chromium-based solid solution embedded within the matrix. Inclusions with thickness of 2–8 μm are present in the intergranular space: (Cr)Ni,Mo,Co, (Cr)Mo,Re and (Cr)Re,Mo. The formation of the Ni(Al,Ti) phase at grain boundaries was identified, contributing to an enhancement in plastic resistance and overall strength of the alloy. Oxidation mechanisms varied across different processing modes, with the size of structural components significantly influencing oxidation kinetics. The weight gain observed in SHS samples was 70 ± 10 g/m2 with oxidation predominantly occurring along the NiAl interphase boundaries and penetrating into the depth of the sample. TEM facilitated the identification of phases enriched with Ti microadditions, reducing the levels of dissolved nitrogen and oxygen within the intermetallic phase to a combined weight percentage (ΣO,N) of 0.0223 wt.%.
In this work, for the first time, we applied and determined the mechanical characteristics of protective coatings made of high-entropy alloy (TiZrVCrAl)N with different architectures onto the surface of Ti-6Al-4V alloy with the initial coarse-grained and ultrafine-grained structure using arc physical vapor deposition. We designed and prepared three coating architectures: a monolayer nitride coating (TiZrVCrAl)N, a multilayer coating consisting of nine alternating layers of TiZrVCrAl and (TiZrVCrAl)N, and a multilayer coating consisting of 720 alternating layers of (TiZrVCrAl)N and TiN, with a total thickness not exceeding 2 microns. We evaluated their protective performances by nanoindentation and scratch tests. Importantly, the effect of the substrate microstructure on the coatings’ performance is investigated by comparing their mechanical behavior on coarse-grained and ultrafine-grained Ti-6Al-4V. Our experimental results show that the coating performance improves with increasing number of layers in the coating, and this effect is even more pronounced for the multilayer coating deposited on the ultrafine-grained titanium alloy substrate. We also find that the (TiZrVCrAl)N/TiN (720 layers) multilayer coating deposited on the UFG Ti-6Al-4V alloy substrate exhibits the highest H/E- and H3/E2-values, indicating the coating’s high innovative potential for performance in extreme conditions. The origins of this phenomenon are analyzed and discussed.
1 October 2015 in International Journal of Self-Propagating High-Temperature Synthesis
NiAl-based high alloy doped with boron was produced by centrifugal SHS and then subjected to remelting at several remelting temperatures ( Trm) above its melting point ( Tm= 1640°C) in order to...
4 October 2026 in Izvestiya Vuzov. Tsvetnaya Metallurgiya (Proceedings of Higher Schools. Nonferrous Metallurgy)
This article presents the results of producing a high-entropy alloy of the Ti–Zr–Al–V–Cr system, intended for practical use as cathode targets in NNV-6.6 vacuum arc systems, using a combined method of melting and remelting. It is shown that direct remelting of the components by vacuum arc melting (VAM) in a copper mould leads to cracking of ingots due to high thermal stresses (cooling rate of 10 2 –10 3 °C/s), while switching off cooling causes copper contamination. To solve the problem, a combined method is proposed: preliminary melting of the components by VAM, followed by vacuum induction remelting (VIM) and casting into a mold. A special ceramic lining based on oxides containing up to 2 wt. % rare-earth metal oxides was used, ensuring minimal impurity contamination. The optimal crystallization parameters were selected: reduction of the cooling rate to 5–10 °C/s, use of a copper base plate for directional heat extraction and a feeder head to compensate for shrinkage effects. Scanning electron microscopy and energy-dispersive X -ray spectroscopy confirmed the chemical homogeneity of the resulting ingots (the contents of Ti, Zr, Al, V, and Cr were 16–27 at. %). The microhardness of the alloy was 768–789 HV with high reproducibility across batches. The cathode targets were successfully tested in the NNV-6.6-I1 installation: single-layer and two types of multilayer coatings were deposited on substrates made of Ti–6Al–4V titanium alloy. The developed technology ensures the production of defect-free ingots of a specified geometry (\(\emptyset \)80–85 mm, h = 45 mm), suitable for industrial use in vacuum arc deposition processes for protective coatings.
19 November 2025 in Transaction Kola Science Centre
The article presents key technological directions of Giredmet aimed at solving the problem of securing raw materials (pure rare-earth and rare metals) for the production of unique alloys. Based on scientific heritage and innovations, the developments encompass: deep hydrometallurgical purification of rare-earth element (REE) oxides; production of individual metals via metallothermic methods and electrolysis; processing of technogenic waste to extract valuable components; smelting a wide range of alloys (high-entropy alloys (HEA), high-temperature shape memory alloys (SMA), pseudo-alloys, metal hydrides, etc.) using vacuum induction melting (VIM), vacuum arc remelting (VAR), and powder metallurgy.