Yang Liang

Yang Liang

Auto-generated profile, based on publicly available information

Yang Liang

State Key Laboratory of Electrical Insulation and Power Equipment, School of Electrical Engineering, Xian Jiaotong University, Xian, China

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 August 2020 in IEEE Transactions on Industry Applications
Verified
Journal Article
Closed access
YLYibin Liu
Yibin Liu
DLDeliang Liang
Deliang Liang
PKPeng Kou
Peng Kou
MZMingkang Zhang
Mingkang Zhang
SCShengliang Cai
Shengliang Cai
CYChuankai Yang
Chuankai Yang
Hybrid distribution transformer (HDT) is a promising device for constructing the future active distribution network. To overcome the limitations of the existing HDT control schemes, a compound control scheme is proposed for a HDT with improved circuit design. In this design, the voltage source converter (VSC) for low-voltage (LV) side voltage regulation is moved to the medium-voltage (MV) side. The compound control scheme is developed based on the dynamic model of this new HDT, which explicitly considers the external disturbances. In this control scheme, two compound controllers are established to regulate the grid current and load voltage, respectively. For each compound controller, feed-forward loops are integrated with the PI regulator, thus suppressing the disturbances. The key feature of this control scheme is that, by using the feed-forward loops, the effect of external step disturbance can be equivalently weaken to an impulse disturbance and, hence, the system robustness can be improved. Simulation and experimental results validate the effectiveness of the proposed control scheme.

19 August 2022 in IEEE Transactions on Industry Applications
Verified
Journal Article
Closed access
SCShuaijun Chu
Shuaijun Chu
DLDeliang Liang
Deliang Liang
SJShaofeng Jia
Shaofeng Jia
YLYang Liang
Yang Liang
As the operating temperature of the motor increases, the material properties will be seriously affected, such as soft magnetic materials and hard magnetic materials, winding insulation properties, etc. For high-speed permanent magnet motors (HSPMM), the higher loss density and smaller heat dissipation area make the impact of temperature more serious. However, according to the test standard, the magnetic properties are usually measured at room temperature, ignoring the effect of temperature. To accurately design magnetic devices, it is necessary to understand the behavior of magnetic materials at different temperatures. In this paper, a new high-speed permanent magnet claw-pole motor (HSPMCPM) with SMC for a wide temperature range is proposed. The design process mainly includes the calculation and analysis of material temperature characteristics, bearing support, topological structure, rotor stress calculation, and so on. Finally, a prototype is manufactured and tested to verify the design process.

12 July 2022 in IEEE Transactions on Industry Applications
Verified
Journal Article
Closed access
YLYang Liang
Yang Liang
DLDeliang Liang
Deliang Liang
PKPeng Kou
Peng Kou
SJShaofeng Jia
Shaofeng Jia
SCShuaijun Chu
Shuaijun Chu
YLYongtao Liang
Yongtao Liang
High speed becomes an important development direction of flywheel energy storage system (FESS) for higher energy storage density. However, the high speed leads to a wide-range and rapid speed variation (tens of thousands of revolutions in seconds) and a limited frequency modulation index, both of which aggravate the current harmonics and deteriorate the robustness of the discharge control, and even lead to instability. To address this issue, this article proposes a robust and practical discharge control strategy for high-speed FESS with RLC filter, which realizes speed adaptation and harmonic suppression. In this scheme, the linear extended state observer and two-degree-of-freedom internal model control (TDOF-IMC) are applied to FESS in the framework of linear active disturbance rejection control (LADRC). Besides, considering that high-speed FESS usually require sensorless control due to magnetic bearings, a reduced-order Luenberger observer for the investigated FESS is proposed. The salient feature of this strategy is to introduce the TDOF-IMC containing FESS dynamic information into LADRC, so that the discharge control is both practical and robust. Experiments and simulations verify the effectiveness of the control strategy.

16 May 2022 in IEEE Transactions on Industry Applications
Verified
Journal Article
Closed access
YLYang Liang
Yang Liang
DLDeliang Liang
Deliang Liang
SJShaofeng Jia
Shaofeng Jia
SCShuaijun Chu
Shuaijun Chu
HWHao Wang
Hao Wang
YLYongtao Liang
Yongtao Liang
High speed becomes an important development direction of permanent magnet synchronous machines (PMSM) for higher power density. However, with the reduction of the switching-to-fundamental frequency ratios (SFRs), the dynamic performance and robustness of the current controller deteriorate and even lead to instability. To address this issue, this article proposes a distinctive current controller designed directly in the discrete-time domain for PMSM, which combines two-degree-of-freedom internal model control (TDOF-IMC) with active damping. The salient feature of this controller is that from the point of directly assigning or optimizing the pole and zero coordinates, a distinctive current controller is designed. Specifically, the TDOF-IMC realizes the ability to arbitrarily arrange the pole–zero placement of the closed-loop transfer function, and, therefore, the current tracking response can be improved. The addition of active damping enhances the antidisturbance ability, and as a result, the dq -axis current oscillations effectively at low SFR are getting weakened. On this basis, current control can achieve better dynamic response and robustness at the same time. Finally, simulation and experimental results validate the effectiveness of the proposed controller.

1 November 2023 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Verified
Journal Article
Closed access
YLYang Liang
Yang Liang
DLDeliang Liang
Deliang Liang
SJShaofeng Jia
Shaofeng Jia
SCShuaijun Chu
Shuaijun Chu
QWQidong Wen
Qidong Wen
SYShuzhou Yang
Shuzhou Yang
Hybrid converter is a promising scheme for current harmonic suppression in high-speed permanent magnet synchronous machine (HSPMSM) drive systems. Considering the limitations of using position sensors, a position sensorless drive for PMSM with hybrid converter is proposed, equipped with online inductance identification utilizing current ripple. The main contribution of this method is less computation and high steady-state position estimation accuracy. This method has two salient features: firstly, the estimated positions updated at different frequencies are achieved by a simple frequency-increasing method; secondly, by fully capitalizing on the hybrid frequency control strategy, a current ripple sampling mechanism is implemented without the need for additional sampling. Finally, the effectiveness of the proposed control scheme is validated by simulation and experimental results.

13 March 2025 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
QWQidong Wen
Qidong Wen
DLDeliang Liang
Deliang Liang
YXYanting Xue
Yanting Xue
ZLZhe Liang
Zhe Liang
LZLishi Zhang
Lishi Zhang
YLYang Liang
Yang Liang
To enhance the endurance and energy utilization efficiency of electric propulsion aircraft (EPA), this article constructs an integrated energy system (IES) architecture for EPA and, on this basis, proposes an energy management strategy (EMS) that considers both transient and steady-state operating conditions. The IES includes super-capacitors (SC), batteries, fuel cells (FCs), open winding permanent magnet synchronous generator, and the corresponding power converters. Under transient conditions with varying loads, low-frequency power is automatically directed to the FC and generator, medium-frequency power is allocated to the battery, and high-frequency power is assigned to the SC. This dynamic power distribution is facilitated by a decentralized droop control within the EMS framework. In addition, the proposed strategy promotes the recovery of the state of charge (SoC) of SCs and batteries, stabilizes the bus voltage, and effectively absorbs regenerative energy. In a steady-state scenario, the EMS proposed in this article optimizes the output power of FC, battery, and generator in a distributed manner, ensuring the system's efficiency and cost-effectiveness. Finally, an experimental platform is established for the proposed IES architecture, and the feasibility of the proposed EMS is validated.