Markellos Ntagios

Markellos Ntagios

Auto-generated profile, based on publicly available information

Markellos Ntagios

Pragmatic Semiconductor Ltd, Cambridge, U.K

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 January 2020 in IEEE Sensors Journal
Verified
Journal Article
Open access
Mahesh SoniMahesh Soni
Mahesh Soni
MBMitradip Bhattacharjee
Mitradip Bhattacharjee
MNMarkellos Ntagios
Markellos Ntagios
RDRavinder Dahiya
Ravinder Dahiya
Temperature sensing is an important parameter needed to be measured by the eSkin during the physical interaction of robots with real-world objects. Yet, most of the work on sensors in eSkin has focused on pressure sensing. Here we present a skin conformable printed temperature sensor with poly(3,4-ethylenedioxythiophene): poly (styrenesulfonate) (PEDOT:PSS)-graphene oxide (GO) as a temperature sensitive layer and silver (Ag) as contact electrodes. The demonstration of PEDOT:PSS/GO as a highly temperature sensitive layer is the distinct feature of the work. The response of presented sensor observed over ~25 °C (room temperature (RT)) to 100 °C, by measuring the variation in resistance across the GO/PEDOT:PSS layer showed ~80% decrease in resistance. The sensitivity of the sensor was found to be 1.09% per °C. The sensor’s response was also observed under static and dynamic bending (for 1000 cycles) conditions. The stable and repeatable response of sensor, in both cases, signifies strong adhesion of the layers with negligible delamination or debonding. In comparison to the commercial thermistor, the printed GO/PEDOT:PSS sensor is faster ( ~73% superior) with response and recovery times of 18 s and 32 s respectively. Finally, the sensor was attached to a robotic hand to allow the robot to act by using temperature feedback.

9 October 2019 in Advanced Intelligent Systems
Verified
Journal Article
Open access
PDF file
MNMarkellos Ntagios
Markellos Ntagios
HNHabib Nassar
Habib Nassar
APAbhilash Pullanchiyodan
Abhilash Pullanchiyodan
WNWilliam Navaraj
William Navaraj
RDRavinder Dahiya
Ravinder Dahiya
Herein, the development of complex 3D intelligent structures such as robotic hands using innovative designs and multimaterial additive manufacturing technology is presented. The distal phalanges of the 3D printed hand presented herein have inherent soft capacitive touch or pressure sensors and embedded electronics. Materials such as thermoplastic polyurethane (TPU), silver paint, conductive polylactic acid composite, graphite ink, etc. are explored to develop five different variants of the sensors using a modified 3D printer, which is capable of extruding conductive ink, metal paste, and polymers. The best‐performing 3D printed soft capacitive touch sensors, formed with silver paint and soft rubber (Ecoflex 00‐30), are integrated on the distal phalanges of the 3D printed robotic hand. These sensors exhibit a stable response with sensitivity of 0.00348 kPa−1 for pressure <10 kPa and 0.00134 kPa−1 for higher pressure. To demonstrate the practical applicability, the 3D printed hand with embedded soft capacitive touch sensors is used for interacting with everyday objects. The tightly integrated sensing elements within the 3D printed structures, as presented herein, can pave the way for a new generation of truly smart material systems that can possibly change their appearance and shape autonomously.

10 June 2022 in IEEE Sensors Journal
Verified
Journal Article
Open access
MNM. Ntagios
M. Ntagios
RDRavinder Dahiya
Ravinder Dahiya
This work presents a soft, flexible, and low-cost capacitive pressure-sensitive insole developed using resource-efficient single-step 3D printing method. Developed using elastomeric materials, the soft and robust sensory insole can bend and twist in extreme angles. The insole is designed to have four sensing zones to capture the pressure information from the entire contact area. The sensors tested under different condition of applied pressure showed reliable response up to 300kPa without saturation. The sensors exhibit a sensitivity of 2.4MPa-1 for range of 0 - 60kPa and 0.526MPa-1 for 60kPa and above with average sensitivity of 1.314 MPa-1 in the entire range. The insole was also tested under varying bending and temperature conditions. Considering the excellent response over a wide pressure range, the presented insole could be used for gait analysis or with anthropomorphic robots for critical information about the terrain morphology. To show the functionality of presented insole, we have also developed an app to display the sensory information obtained via custom-made electronics circuit.

1 October 2018
Verified
Conference Paper
Closed access
HNHabib Nassar
Habib Nassar
MNMarkellos Ntagios
Markellos Ntagios
WNWilliam Navaraj
William Navaraj
RDRavinder Dahiva
Ravinder Dahiva
This paper presents a novel additive manufacturing method to obtain bendable smart sensing structures having printed strain sensors and interconnects to gain access to embedded electronic components. The presented smart structure is obtained by simultaneous printing of functional materials along with conventional polymer-based 3D printing materials. To this end, a low-cost open-source 3D printer was augmented with a silver palladium metallic paste extruder. The strain sensors in the presented 3D printed smart structure are particularly useful for wearable motion sensing applications such as knee joint motion analysis. The printed interconnects allow for electrical connection with the Light Emitting Diodes (LEDs) embedded within the 3D printed structure. With electronic components embedded in the flexible 3D printed structure, this work also demonstrates a novel method for soft packaging of electronic and sensing components. The electrical tests conducted on the smart structure show excellent electrical continuity. The 3D printed strain sensors, tested in static and dynamic bending conditions, showed a linear response of resistance. Under no strain, the resistance of the sensor was measured to be 0.9671 n (resistivity of 9.671×10 -6 Ω.m) and during testing it exhibited a gauge factor of 1. Multi-material additive manufacturing demonstrated in this paper opens a new direction for fabrication of complex 3D structures with embedded sensors and electronics and offers significant advantages for rapid prototyping and packaging.

1 February 2023 in Additive Manufacturing
Verified
Journal Article
Open access
MNMarkellos Ntagios
Markellos Ntagios
HNHabib Nassar
Habib Nassar
RDRavinder Dahiya
Ravinder Dahiya

1 October 2018
Verified
Conference Paper
Closed access
MNMarkellos Ntagios
Markellos Ntagios
WNWilliam Navaraj
William Navaraj
RDRavinder Dahiya
Ravinder Dahiya
3D printing is widely used as the quickest way to transform design concept to the physical implementation. Recent advances in this field of additive manufacturing have allowed printing of several types of polymers, including soft material. While 3D printing allows easy way to develop complex 3D shapes, it does not allow these shapes to have sensory capability. However, in applications such as robotics and prosthetics, the 3D printed structures with sensory capability are much needed. This paper presents an innovative way to use 3D printing method to develop of complex shapes such as robotic finger with embedded capacitive touch sensors. The concept has been demonstrated by designing and printing the distal phalanx of finger with soft material. Embedding the touch sensors within the phalanx is advantageous in terms of robustness, aesthetics, water/ambient-proofing, reliability of the sensing layer as well as to overcome the traditional robotic skin issue of wiring complexity.