Johan Sundin

Johan Sundin

Auto-generated profile, based on publicly available information

Johan Sundin

FLOW

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 March 2021 in Nature Physics
Verified
Journal Article
Closed access
PDF file
HHHiroki Hiroki
Hiroki Hiroki
EIEmre Iseri
Emre Iseri
XWXi Wei
Xi Wei
KKKerem Kaya
Kerem Kaya
GDGiacomo Di Dio
Giacomo Di Dio
WWWouter van der Wijngaart
Wouter van der Wijngaart

6 April 2021 in Journal of Fluid Mechanics
Verified
Journal Article
Open access
PDF file
JSJohan Sundin
Johan Sundin
SZStéphane Zaleski
Stéphane Zaleski
SBShervin Bagheri
Shervin Bagheri
Liquid-infused surfaces (LISs) are a promising technique for reducing friction, fouling and icing in both laminar and turbulent flows. Previous work has demonstrated that these surfaces are susceptible to shear-driven drainage. Here, we report a different failure mode using direct numerical simulations of a turbulent channel flow with liquid-infused longitudinal grooves. When the liquid–liquid surface tension is small and/or grooves are wide, we observe travelling-wave perturbations on the interface with amplitudes larger than the viscous sublayer of the turbulent flow. These capillary waves induce a roughness effect that increases drag. The generation mechanism of these waves is explained using the theory developed by Miles for gravity waves. Energy is transferred from the turbulent flow to the LIS provided that there is a negative curvature of the mean flow at the critical layer. Given the groove width, the Weber number and an estimate of the friction Reynolds number, we provide relations to determine whether a LIS behaves as a smooth or rough surface in a turbulent flow.

26 October 2022 in Journal of Fluid Mechanics
Verified
Journal Article
Open access
PDF file
JSJohan Sundin
Johan Sundin
SBShervin Bagheri
Shervin Bagheri
Using numerical simulations, we investigate the effects of Marangoni stresses induced by surfactants on the effective slip length of liquid-infused surfaces (LIS) with transverse grooves. The surfactants are assumed soluble in the external liquid shearing the surface and can adsorb onto the interfaces. Two different adsorption models are used: a classical Frumkin model and a more advanced model that better describes the decrease of surface tension for minuscule concentrations. The simulations show that LIS may face even more severe effects of surfactants than previously investigated superhydrophobic surfaces. Constructing an analytical model for the effective slip length, we can predict the critical surfactant concentration for which the slip length decreases significantly. This analytical model describes both adsorption models of LIS on a unified framework if properly adjusted. We also advance the understanding of when surfactant advection gives rise to highly skewed interfacial concentrations: the so-called partial stagnant cap regime. To a good approximation, this regime can only exist below a specific surfactant concentration given by the Marangoni number and the strength of the surfactants.

6 April 2022 in Journal of Fluid Mechanics
Verified
Journal Article
Open access
PDF file
ULUǧis Lācis
Uǧis Lācis
MPMichele Pellegrino
Michele Pellegrino
JSJohan Sundin
Johan Sundin
GAGustav Amberg
Gustav Amberg
SZStéphane Zaleski
Stéphane Zaleski
SBShervin Bagheri
Shervin Bagheri
The motion of the three-phase contact line between two immiscible fluids and a solid surface arises in a variety of wetting phenomena and technological applications. One challenge in continuum theory is the effective representation of molecular motion close to the contact line. Here, we characterize the molecular processes of the moving contact line to assess the accuracy of two different continuum two-phase models. Specifically, molecular dynamics simulations of a two-dimensional droplet between two moving plates are used to create reference data for different capillary numbers and contact angles. We use a simple-point-charge/extended water model. This model provides a very small slip and a more realistic representation of the molecular physics than Lennard-Jones models. The Cahn–Hilliard phase-field model and the volume-of-fluid model are calibrated against the drop displacement from molecular dynamics reference data. It is shown that the calibrated continuum models can accurately capture droplet displacement and droplet break-up for different capillary numbers and contact angles. However, we also observe differences between continuum and atomistic simulations in describing the transient and unsteady droplet behaviour, in particular, close to dynamical wetting transitions. The molecular dynamics of the sheared droplet provide insight into the line friction experienced by the advancing and receding contact lines. The presented results will serve as a stepping stone towards developing accurate continuum models for nanoscale hydrodynamics.

27 December 2018 in Journal of Fluid Mechanics
Verified
Journal Article
Closed access
PDF file
JSJohan Sundin
Johan Sundin
SBShervin Bagheri
Shervin Bagheri
Surfaces with filamentous structures are ubiquitous in nature on many different scales, ranging from forests to micrometre-sized cilia in organs. Hairy surfaces are elastic and porous, and it is not fully understood how they modify turbulence near a wall. The interaction between hairy surfaces and turbulent flows is here investigated numerically in a turbulent channel flow configuration at friction Reynolds number $Re_{\unicode[STIX]{x1D70F}}\approx 180$ . We show that a filamentous bed of a given geometry can modify a turbulent flow very differently depending on the resonance frequency of the surface, which is determined by the elasticity and mass of the filaments. Filaments having resonance frequencies lower than the main frequency content of the turbulent wall-shear stress conform to slowly travelling elongated streaky structures, since they are too slow to adapt to fluid forces of higher frequencies. On the other hand, a bed consisting of stiff and low-mass filaments has a high resonance frequency and shows local regions of increased permeability, which results in large entrainment and a vast increase in drag.

1 April 2021 in Soft Robotics
Verified
Journal Article
Open access
JSJohan Sundin
Johan Sundin
KKKatherine Kokmanian
Katherine Kokmanian
MFMatthew K. Fu
Matthew K. Fu
SBShervin Bagheri
Shervin Bagheri
MHMarcus Hultmark
Marcus Hultmark
To control and navigate micro air vehicles (MAVs) efficiently, there is a need for small, lightweight, durable, sensitive, fast, and low-power airspeed sensors. When designing sensors to meet these requirements, soft materials are promising alternatives to more traditional materials due to the large deformations they can withstand. In this article, a new concept of a soft material flow sensor is presented based on elastic filament velocimetry, which fulfills all necessary criteria. This technique measures flow velocity by relating it to the strain of a soft ribbon suspended between two static supports and subjected to a flow of interest. The ribbon is manufactured from polydimethylsiloxane and can be made piezoresistive by the addition of silver nanowires. With the described manufacturing method, the sensor can be made using common laboratory tools, outside of a clean room, significantly reducing its complexity. Furthermore, it can be operated using a simple and lightweight circuit, making it a convenient alternative for MAVs. Using a piezoresistive material allows for the flow velocity to be calibrated to the resistance change of the strained ribbon. Although certain challenges remain unsolved, such as polymer creep, the sensor has demonstrated its ability to measure flow velocities down to 4 m/s in air through experiments. A time-dependent analytical model is also provided. The model shows that the current sensor has a bandwidth of 480 Hz. Most importantly, the sensitivity and the bandwidth of the sensor can be varied strictly by modifying the geometry and the material properties of the ribbon.