The operational amplifier is a key building block in analog systems. However, the design process of the operational amplifier is time consuming and heavily depends on engineers’ experiences. This article presents OPAMP-Generator, an analog operational amplifier generator, which automates the full design flow from user-defined specifications to GDSII layout without human intervention. OPAMP-Generator includes behavioral-level topology optimization, efficient sizing algorithm based on the classical $ {g_{m}/I_{d}}$ design methodology, and automated layout generation. The behavioral-level description of the opamp is represented by the directed acyclic graph (DAG) and a customized variational graph autoencoder is proposed to embed the discrete graph representation into a low-dimensional continuous space. The topology of the opamp can thus be optimized in the latent space, which greatly improves the optimization efficiency. The sizing algorithm based on ${g_{m}/I_{d}}$ methodology can guarantee the quality of transistor-level circuit implementation. The constraints of the layouts can be naturally derived from the topology level, which facilities the automatic generation of layouts. Experimental results demonstrate that our proposed method can efficiently synthesize operational amplifiers with competitive performances compared to manual designs.
21 June 2023 in IEEE Journal of Solid-State Circuits
This article describes an ultra-high input-impedance active electrode (AE) circuit and the system to sense biopotential signals through a capacitively coupled interface. Various techniques from both circuit and system aspects are used to eliminate the input parasitic capacitance of the AE. On-chip parasitic capacitance is compensated by an auto-calibrated positive feedback loop (PFL) without applying any reference signal. A capacitor down-scaling technique combined with SAR-assisted PFL calibration enables femtofarad-level resolution of the capacitor array, alleviating the practical constraints of the conventional PFL to implement a small capacitor below 10 fF. Besides, a dummy input structure ensures that the pad and electrostatic discharge (ESD) capacitances are also canceled by the PFL, while off-chip parasitic capacitance on the printed circuit board (PCB) is nulled by active shielding. Fabricated in a standard 0.18- $\mu \text{m}$ 1P6M CMOS process, the AE achieves an ultra-high input impedance of 136 $\text{G}\Omega $ at 60 Hz (average of 10 samples). This is equivalent to an input capacitance of 19.5 fF and corresponds to a $2.7\times $ – $68\times $ improvement over the state-of-the-art. The AE exhibits an input signal range of 700 mVpp and an input-referred noise of $0.72 \mu \text{V}_{\mathrm {rms}}$ (0.5–100 Hz) while consuming $10.46 \mu \text{W}$ from a 1.2-V supply. Each AE integrates an IC and a 3-cm2 copper electrode on the PCB, and the wearable system prototypes successfully measured high-quality electrocardiogram (ECG) and electroencephalogram (EEG) signals from test subjects through capacitively coupled interfaces.
4 April 2024 in IEEE Journal of Solid-State Circuits
This article presents a low-power (LP), compact, wideband (WB) low-noise transconductance amplifier (LNTA)-first receiver (RX) designed for software-defined radios (SDRs). It comprises the LNTA, frequency divider, mixer, and trans-impedance amplifier (TIA). The LNTA utilizes a common gate (CG)-common source (CS) structure without on-chip inductors and incorporates gm-boosting and current reuse techniques to effectively reduce power consumption. A novel noise-canceling (NC) strategy is proposed to break the inherent tradeoff between input impedance matching, noise figure (NF), and gain. The divider adopts a windmill structure based on NAND gates, while 25% duty-cycle quadrature clocks drive the double-balanced passive mixer. The third-order filtering TIA is based on a three-stage pseudo-differential operational transconductance amplifier (OTA). It implements $RC$ and feedforward (FF) compensation techniques to attain a 3.25-GHz unity gain loop bandwidth (BW) and 68-dB loop gain. Fabricated in a 40-nm LP CMOS technology, the chip features 38-dB conversion gain, 50-MHz baseband (BB) BW, 3.5-dB NF, and in-band (IB) output third-order intercept point of up to 40 dBm. The RX operates over a frequency range of 0.1–5.5 GHz. It consumes 36 mW of static power in the RX signal path and 15 mW of dynamic power in the local oscillator (LO) path at 5 GHz. The core area is only 0.1 mm2.
13 June 2023 in IEEE Journal of Solid-State Circuits
This article presents a fully integrated digital polar transmitter (DPTX) incorporating an efficiency-enhanced digital power amplifier (DPA) and a high-resolution digital-to-time converter (DTC). The proposed single-ended Doherty (SED) PA topology with switched-capacitor (SC) arrays can generate four power efficiency peaks that significantly improve the power-added efficiency (PAE) at the power amplifier (PA)’s power back-offs (PBOs). In addition, this work utilizes a three-segment DTC, built with a delay-locked loop (DLL), to improve the phase resolution and enable real-time process-voltage-temperature (PVT) calibration of the DTC. Fabricated in a 28 nm CMOS technology, the DPTX achieves a peak output power ( $P_{\mathrm{out}})$ of 27.7 dBm and a peak PAE of 33.4% at a 2.1 GHz carrier frequency. The PAEs at 2.5, 6, and 12 dB PBOs are 31.1%, 24.5%, and 18%, respectively. With the 2.1 GHz carrier, the DTC achieves 360 $^{\circ}$ full output phase range, $\pm$ 1.3 $^{\circ}$ differential nonlinearity (DNL), $\pm$ 1.7 $^{\circ}$ integral nonlinearity (INL), and $-$ 133.86 dBc/Hz phase noise at a frequency offset of 1 MHz, while the power dissipation is only 14 mW. When testing the 10 MHz (and 20 MHz) long term evolution (LTE) 64 QAM signals with a 6.2 (5.0) dB peak-to-average power ratio (PAPR), the DPTX achieves an average $P_{\mathrm{out}}$ of 21.5 (22.7) dBm, an average PAE of 23.5% (24.6%), an average system efficiency (SE) of 22.5% (23.8%)–, 30.6 (–27.7) dB error vector magnitude (EVM), and –34.2/–32.6 (–30.1/–29.2) dBc adjacent channel leakage ratio (ACLR). Note that these results have been achieved with only the on-chip digital pre-distortion (DPD) algorithm.
1 February 2024 in IEEE Transactions on Circuits and Systems II: Express Briefs
This paper presents a power-efficient fourth-order, 50-MHz active-RC filter with high dynamic range (DR). Unlike conventional Tow-Thomas biquads, the proposed design employs a passive integrator as the second pole to reduce power consumption, enhance noise performance, and facilitate frequency compensation. The active integrator features a two-stage operational transconductance amplifier (OTA) with a push-pull output, ensuring linearity and reducing the OTA’s gain requirements. Fabricated in standard 0.18-μm CMOS technology, the proposed filter achieves an in-band (IB) input third-order intercept point (IIP3) of +29.9 dBm at 30 MHz and an input-referred IB integrated noise of 163.8 μVRMS, while consuming 5.4 mW for a 50-MHz bandwidth.