Peng Cao

Peng Cao

Auto-generated profile, based on publicly available information

Peng Cao

State Key Laboratory of Integrated Chips and Systems, Fudan University, Shanghai, China

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 December 2019 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
PCPeng Cao
Peng Cao
YQYao Qian
Yao Qian
PXPan Xue
Pan Xue
DLDanzhu Lu
Danzhu Lu
JHJie He
Jie He
ZHZhiliang Hong
Zhiliang Hong
This paper presents a bipolar-input thermoelectric energy-harvesting interface based on boost/flyback hybrid converter (BFHC). Two-type ring oscillators are combined to form as a complementary group with bipolar-input voltage operating range for self-start. With the technique of combining the boost converter and flyback converter together, the system is able to convert the energy with bipolar-input voltages. The open-circuit voltage maximum power point tracking (MPPT) method is adopted in this harvester to extract as much energy as possible from the thermoelectric generator. By dynamically adjusting the switching frequency according to the input power, the system achieves a high conversion efficiency with a wide input range. Implemented in 180-nm CMOS process, the harvester achieves a peak conversion efficiency of 84% at VTEG=260 mV and 79% at VTEG=-300 mV. In addition, the harvester can self-startup with minimum voltages of 129 mV with a positive input voltage and -140 mV with a negative input voltage.

1 February 2019
Verified
Conference Paper
Closed access
PCPeng Cao
Peng Cao
YQYao Qian
Yao Qian
PXPan Xue
Pan Xue
DLDanzhu Lu
Danzhu Lu
JHJie He
Jie He
ZHZhiliang Hong
Zhiliang Hong
Recent advances in energy-harvesting techniques have allowed wearable and IoT devices to operate without batteries. A thermoelectric generator (TEG) is one energy source that can provide a bipolar voltage that is proportional to the temperature difference between its two sides. Most of the prior TEG-harvesting systems could handle the positive input voltage [1-3]; however, the TEG's input voltage polarity may reverse due to environmental changes. Only a few prior publications provide a method to deal with the bipolar input voltage [4-6]. To harvest bipolar input energy, a switch-matrix-based boost converter is proposed in [4], but it cannot self-start and dynamically track the maximum power point. [5] and [6] provide methods for bipolar self-startup with an ultra-low input voltage, but both of them suffer from a low conversion efficiency. Hence, there is no complete system suitable for bipolar-input TEG energy harvesting. A solution must address three challenges: (1) the transfer of energy from a bipolar input voltage via a high-efficiency converter; (2) system self-start-up with a reasonably low bipolar input voltage; (3) a maximum power point tracking (MPPT) method for bipolar input voltage. This paper proposes a bipolar-input boost/flyback hybrid converter (BFHC) with an on-chip cold start-up for TEG energy harvesters.

13 June 2023 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
TWTao Wang
Tao Wang
JLJieyang Li
Jieyang Li
DHDi Hua
Di Hua
LLLiangbo Lei
Liangbo Lei
PCPeng Cao
Peng Cao
ZHZhiliang Hong
Zhiliang Hong
This article presents a fully integrated digital polar transmitter (DPTX) incorporating an efficiency-enhanced digital power amplifier (DPA) and a high-resolution digital-to-time converter (DTC). The proposed single-ended Doherty (SED) PA topology with switched-capacitor (SC) arrays can generate four power efficiency peaks that significantly improve the power-added efficiency (PAE) at the power amplifier (PA)’s power back-offs (PBOs). In addition, this work utilizes a three-segment DTC, built with a delay-locked loop (DLL), to improve the phase resolution and enable real-time process-voltage-temperature (PVT) calibration of the DTC. Fabricated in a 28 nm CMOS technology, the DPTX achieves a peak output power ( $P_{\mathrm{out}})$ of 27.7 dBm and a peak PAE of 33.4% at a 2.1 GHz carrier frequency. The PAEs at 2.5, 6, and 12 dB PBOs are 31.1%, 24.5%, and 18%, respectively. With the 2.1 GHz carrier, the DTC achieves 360 $^{\circ}$ full output phase range, $\pm$ 1.3 $^{\circ}$ differential nonlinearity (DNL), $\pm$ 1.7 $^{\circ}$ integral nonlinearity (INL), and $-$ 133.86 dBc/Hz phase noise at a frequency offset of 1 MHz, while the power dissipation is only 14 mW. When testing the 10 MHz (and 20 MHz) long term evolution (LTE) 64 QAM signals with a 6.2 (5.0) dB peak-to-average power ratio (PAPR), the DPTX achieves an average $P_{\mathrm{out}}$ of 21.5 (22.7) dBm, an average PAE of 23.5% (24.6%), an average system efficiency (SE) of 22.5% (23.8%)–, 30.6 (–27.7) dB error vector magnitude (EVM), and –34.2/–32.6 (–30.1/–29.2) dBc adjacent channel leakage ratio (ACLR). Note that these results have been achieved with only the on-chip digital pre-distortion (DPD) algorithm.

24 October 2023 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
PCPeng Cao
Peng Cao
DLDanzhu Lu
Danzhu Lu
JXJiawei Xu
Jiawei Xu
XZXiaoyang Zeng
Xiaoyang Zeng
ZHZhiliang Hong
Zhiliang Hong
This article presents a time-domain-controlled (TDC) single-inductor triple-output (SITO) step-up converter for portable devices with a bipolar power supply. A time-domain controller is utilized in the proposed converter to achieve a minimized delay time and thus ensure a high-conversion ratio (CR) with a switching frequency of 2 MHz. The proposed power converter employs a time-domain energy distribution (ED) balance scheme to ensure the bipolar outputs are symmetrically regulated. In addition, with the assistance of the output offset correction circuits, the load regulation of the TDC-SITO converter is greatly improved. By using an analog-to-digital converter (ADC)-assisted fast-settling loop, the converter achieves an excellent load transient response with low undershoot/overshoot voltages. Powered by a lithium-ion battery, the TDC-SITO converter can generate a bipolar power supply of $\pm$ 12 V and a standard 5 V output voltage, indicating a maximum CR of 8.8×. Implemented in a 180 nm bipolar-CMOS-DMOS (BCD) process, the converter achieves a peak conversion efficiency of 91.6% at an output power of 2.25 W. With a load current step of 100 mA between two output voltages of $\pm$ 10 V, the output voltages recover their normal values within 100 $\mu$ s while the undershoot/overshoot voltages are below 160 mV. The maximum output power of the TDC-SITO converter is 9.6 W.

13 October 2023 in IEEE Transactions on Circuits and Systems I: Regular Papers
Verified
Journal Article
Closed access
PXPeng Xu
Peng Xu
JKJin Kang
Jin Kang
ZTZhiguo Tong
Zhiguo Tong
PCPeng Cao
Peng Cao
YWYingjie Wang
Yingjie Wang
ZHZhiliang Hong
Zhiliang Hong
Envelope tracking (ET) and average power tracking (APT) have been widely used as supply modulators of power amplifiers (PAs). To meet the new challenges brought by the 5G NR standard, the symbol power tracking (SPT) technique is proposed, which is more efficient than ET and more flexible than APT. For the application of subcarrier spacing (SCS) of 15- $\sim$ 60kHz in the frequency range 1 (FR1), this paper proposed a buck-boost SPT supply modulator with a transition time below 1.17- $\mu $ s for 5G NR PA in the smartphone. The combination of three techniques improves the voltage transition speed. The charge-pump-based switching power modulator increases the output voltage higher than the battery voltage and offers a high voltage source for the auxiliary current paths (ACP). The ACP introduces additional currents to charge/discharge the 1- $\mu $ F output capacitor. The end-point-prediction (EPP) scheme lets the compensator convert directly from one steady state to the next. This supply modulator circuit is designed and fabricated using 0.18- $\mu $ m BCD technology. The output voltage range is 1–5-V. The maximum transition speed can be up to 0.37- $\mu $ s/V and 0.15- $\mu $ s/V for up-tracking and down-tracking, respectively.

28 February 2023 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
PXPeng Xu
Peng Xu
XZXueli Zhang
Xueli Zhang
PCPeng Cao
Peng Cao
TWTingting Wei
Tingting Wei
ZTZhiguo Tong
Zhiguo Tong
ZHZhiliang Hong
Zhiliang Hong
Envelope tracking is an effective way to improve the efficiency of radio frequency power amplifiers (PAs). This paper presents a wideband hybrid envelope tracking supply modulator (ETSM) for 5G New Radio (NR) PAs. To reach a wide envelope tracking bandwidth of 200MHz while maintaining high power efficiency, this work utilized a linear amplifier (LA) with accurate frequency compensation and enhanced driving capability. The proposed low-pass sense and control (LPSC) circuit ensures that the switching power amplifier (SPM) only tracks the low-frequency components of the envelope to reduce the switching power loss. The proposed dual-path duty modulator regulates the voltage across the AC-coupling capacitor. This supply modulator circuit is designed and fabricated using 0.18μm BCD technology. When tracking 200MHz bandwidth envelope signals, the prototype ETSM achieves 78.5% efficiency at the output power of 2.7W when taking a realistic 4Ω//600pF load as the PA model.