25 April 2023 in IEEE Sensors Journal
A surface-mounted tilt sensor was designed and fabricated to measure the inclination angle of engineered structures or slopes in two directions. The device utilizes two strain-sensitive FBGs for tilt angle measurement bi-directionally and one strain-free FBG to provide temperature compensation. In this work, a tilt sensor prototype was fabricated using a 3D printer, with a robust enclosure and a miniature actuator with dimensions of 115 x 65 x 30 mm and 45 x 20 x 3 mm, respectively. The device was first calibrated in the laboratory for tilt and temperature parameters. For tilt calibration, the device yields a sensitivity value of 0.0135 nm/° and 0.0123 nm/° for +x and -x directions. On the other hand, the device delivers a sensitivity value of 0.0105 nm/°C as the response to temperature changes. The tilt sensor was also tested for suitability in a real-field deployment where it was installed on a retaining wall and was left for 4 weeks. The field test data indicates no vertical displacement of the wall since the device exhibits zero inclination changes during the test period. This compact, robust, and easy-to-install tilt sensor has excellent potential for various geotechnical applications, mainly in landslide detections, ground movement, and engineered slope monitoring.
30 December 2024 in IEEE Sensors Journal
WBW. A. F. W. Burhanuddin
This study presents the design, fabrication, and performance evaluation of an optical fiber Bragg grating (FBG)-based pore pressure sensor for geotechnical borehole applications. The sensor comprises a cylindrical body, 3-dimensional (3D), printed from polylactic acid (PLA) material, with dimensions of 40 mm in diameter and 155 mm in length. The transducer holding the FBG utilizes a square bellows design and was 3D printed using thermoplastic polyurethane (TPU) material, taking advantage of its good flexibility. This transducer was positioned inside a cylindrical housing to allow pore pressure measurement to take place effectively. Two FBGs, denoted FBG P and FBG T, were used to measure pore pressure and temperature, respectively. Experimental results demonstrate a pressure sensitivity of 1.224 pm/kPa for FBG P with a linearity of 99.41%. Besides that, the results also demonstrate FBG T’s effectiveness in giving temperature compensation to FBG P during pore pressure measurement. This innovative sensor design offers a compact and versatile solution for pore pressure measurement in geotechnical applications, combining the benefits of FBG technology with 3D printing capabilities.
16 July 2024 in IEEE Sensors Journal
WBW. A. F. W. Burhanuddin
This study proposes an innovative approach for fabricating a multi-parameter sensor based on fiber Bragg gratings (FBG) using 3D printing technology. In this sensor design, three FBGs were used: one for vertical earth pressure measurement, FBG E; one for pore pressure measurement, FBG P; and the other for temperature compensation, FBG T. The results demonstrate the sensor’s effectiveness in measuring vertical earth and pore pressure, achieving 43.1550 pm/psi sensitivities and 0.9841 pm/psi, respectively. Furthermore, FBG E and FBG P also exhibited high linearity values of 99.5% and 99.1%, respectively, demonstrating their ability to provide accurate measurements. Conducted measurements also showed FBG T’s effectiveness in giving temperature compensation for FBG E and FBG P during pressure measurements. Additionally, the study highlighted the suitability of acrylonitrile butadiene styrene (ABS) material for sensor design and prototyping due to its capability to withstand high temperatures and pressures, making it ideal for various applications in harsh environments.
18 March 2024 in IEEE Sensors Journal
This study proposes a novel optical fiber Bragg grating (FBG)-based load cell sensor using 3D printing technology. It explores the impact of the infill density and pattern on the FBG’s temperature and mechanical strain sensitivity. Two FBGs were used, one for strain measurement, FBG L, and the other for temperature compensation, FBG T. Conducted measurements show that the strain-sensitive FBG L and strain-free FBG T exhibited a similar average temperature sensitivity value of around 10.5 pm/°C with a good linearity value of 99.92%. This will also allow the unstrained FBG T to effectively compensate for FBG L’s temperature changes during load measurement. Under varied load conditions, load cell sensors with lower infill density, such as 20%, displayed more significant average wavelength shift and increased strain sensitivities compared to those with higher infill density, such as 80%, due to having more voids and hollow sections within its actuator. This facilitates easier deformation, thus inducing more significant stretching on FBG L. Regarding the infill pattern, the gyroid pattern outperformed the tri-hexagon in both average wavelength shift and strain responses, showing its suitability for precise measurements under diverse loads. Therefore, this work demonstrates the critical role of the infill density and pattern in the performance of an efficient load cell sensor using FBGs.
1 August 2023 in Optical Engineering
An optical-based pressure sensor for a 150 × 150 mm surface was designed and fabricated. The sensor utilizes a fiber Bragg grating (FBG) attached to a 30 × 30 × 30 mm actuator as the pressure sensing mechanism. The middle section of the actuator, which is circular, can bend into an elliptical form and, in the process, pull the FBGP via both ends when force or pressure is applied, thus converting the pressure applied to its surface into a wavelength shift. In laboratory testing, a sensitivity of 0.152 nm / kPa was obtained. Subsequently, the pressure sensor was tested in the field by burying it 20 cm underground to measure soil pressure, while another FBG was spliced in series to the FBGP to compensate for temperature variations. Testing shows that the proposed design can realize a compact optical-based pressure sensor with enhanced soil monitoring applications such as dynamic soil pressure caused by soil movement.
1 March 2022 in Optical Engineering
An innovative vibration sensor based on a Fabry–Perot interferometer (FPI) using fiber Bragg grating (FBG) reflectors was demonstrated in this work. The sensor was designed to be compact and easy to fabricate, independent of temperature, to overcome limitations seen in previous designs, providing an effective correction for temperature effects in FBG-based FPI (FBG-FPI) sensors. A laser source with a peak wavelength of 1547.42 nm obtained from the FBG reflective peak was used to illuminate the FBG-FPI so that the light source was always within the FBG-FPI optimum wavelength operating range of 1547.15 to 1547.80 nm. The sensor was shown to capture a 3-kHz burst signal from a signal generator in 1-, 2-, and 3-Hz intervals. In addition, the work carried out has revealed that the sensor could be used to capture sinusoidal signals at frequencies up to 9 kHz, creating a performance comparable with many existing conventional piezoelectric sensors. Furthermore, the ability to operate regardless of any ambient temperature changes [from 26.5°C (room temperature) up to 80°C] opens the way to use such a sensor system over a wide range of engineering applications taking advantage of the next generation of FBG-based FPIs.