A key challenge for practical magnesium–sulfur (Mg–S) batteries is to overcome the sluggish conversion kinetics of sulfur cathodes, achieving a high energy density and long‐lasting battery life. To address this issue, a doping strategy is demonstrated in a model Ketjenblack sulfur (KBS) cathode by introducing selenium with a high electronic conductivity. This leads to a significantly enhanced charge transfer in the resultant KBS1−xSex cathodes, giving rise to a higher S utilization and less polysulfide dissolution. Compared to the bare S cathode, the S‐Se composite cathodes exhibit a higher capacity, smaller overpotentials, and improved efficiency, serving as better benchmark compounds for high‐performance Mg–S batteries. First principles calculations reveal a charge transport mechanism via electron polaron diffusion in the redox end‐products, that enhances the reaction kinetics. By suppressing polysulfide dissolution in the electrolyte, the use of the KBS1−xSex cathodes also enables a more uniform anode reaction, and thereby significantly extends the cyclability of the cells. To improve the performance, further efforts are made by implementing a Mo6S8 modified separator into the cell. With an optimized cathode composition of KBS0.86Se0.14, the cell applying modified separator shows an improvement of capacity retention by >50% after 200 cycles.
19 November 2024 in Angewandte Chemie International Edition
Rechargeable magnesium batteries are promising for future energy storage. However, among other challenges, their practical application is hindered by low coulombic efficiencies of magnesium plating and stripping. Fundamental processes such as the formation, structure, and stability of passivation layers and the influence of different electrolyte components on them are still not fully understood. In this work, we gain unique insights into the initial Mg plating and stripping cycles by comparing magnesium bis(trifluoromethanesulfonyl)imide (Mg(TFSI) 2 )‐ and magnesium tetrakis(hexafluoroisopropyloxy)borate (Mg[B(hfip) 4 ] 2 )‐based electrolytes, each with and without MgCl 2 , on gold electrodes by highly sensitive operando electrochemical quartz crystal microbalance with dissipation monitoring (EQCM−D) applying hydrodynamic spectroscopy. With the stable Mg[B(hfip) 4 ] 2 ‐based electrolytes, highly efficient and interphase‐free cycling is possible and passivation layers are attributed to electrolyte contaminants. These are forming and degrading during the so‐called initial conditioning process. With the more reactive Mg(TFSI) 2 ‐based electrolyte, thick passivation layers with small pores are growing during cycling. We demonstrate that the addition of chloride lowers the amount of passivated Mg deposits in these electrolytes and accelerates the currentless dissolution of the passivation layer. This has a positive effect since we observe the most efficient cycling and uniform deposition when no interphase is present on the electrode.
Rechargeable magnesium batteries (RMBs) have the potential to provide a sustainable and long‐term solution for large‐scale energy storage due to high theoretical capacity of magnesium (Mg) metal as an anode, its competitive redox potential (Mg/Mg2+:−2.37 V vs. SHE) and high natural abundance. To develop viable magnesium batteries with high energy density, the electrolytes must meet a range of requirements: high ionic conductivity, wide electrochemical potential window, chemical compatibility with electrode materials and other battery components, favourable electrode‐electrolyte interfacial properties and cost‐effective synthesis. In recent years, significant progress in electrolyte development has been made. Herein, a comprehensive overview of these advancements is presented. Beginning with the early developments, we particularly focus on the chemical aspects of the electrolytes and their correlations with electrochemical properties. We also highlight the design of new anions for practical electrolytes, the use of electrolyte additives to optimize anode‐electrolyte interfaces and the progress in polymer electrolytes.
Calcium (Ca) batteries are attractive post‐lithium battery technologies, due to their potential to provide high‐voltage and high‐energy systems in a sustainable manner. We investigated herein 1,5‐poly(anthraquinonylsulfide) (PAQS) for Ca‐ion storage with calcium tetrakis(hexafluoroisopropyloxy)borate Ca[B(hfip)4]2 [hfip=OCH(CF3)2] electrolytes. It is demonstrated that PAQS could be synthesized in a cost‐effective approach and be processed environmentally friendly into the electrodes. The PAQS cathodes could provide 94 mAh g−1 capacity at 2.2 V vs. Ca at 0.5C (1C=225 mAh g−1). However, cycling of the cells was severely hindered due to the fast degradation of the metal anode. Replacing the Ca metal anode with a calcium‐tin (Ca−Sn) alloy anode, the PAQS cathodes exhibited long cycling performance (45 mAh g−1 at 0.5C after 1000 cycles) and superior rate capability (52 mAh g−1 at 5C). This is mainly ascribed to the flexible structure of PAQS and good compatibility of the alloy anodes with the electrolyte solutions, which allow reversible quinone carbonyl redox chemistry in the Ca battery systems. The promising properties of PAQS indicate that further exploration of the organic cathode materials could be a feasible direction towards green Ca batteries.
Magnesium–sulfur (Mg–S) batteries are emerging as promising energy storage systems due to their cost‐effectiveness, safety, and high theoretical volumetric energy density. However, their practical implementation is hindered by sluggish sulfur redox kinetics with Mg2+ and severe polysulfide shuttling. Here, a double‐divalent Mg–Ca hybrid electrolyte is introduced, where a small amount of Ca2+ additive significantly enhances sulfur redox kinetics, leading to higher sulfur utilization. Notably, Ca2+ primarily facilitates the solid‐to‐solid conversion of disulfide to sulfide. In addition to the cathode reaction, the Mg–Ca hybrid electrolyte also contributes to the anode reaction; it enables smoother Mg plating and reduces overpotential with the long cycle (>1000 cycles). For mitigating the polysulfide shuttling, the glass fiber separator with ultrasmall α‐MnO2 nanoparticles is modified to adsorb polysulfide. This synergistic strategy of electrolyte and separator engineering enables the Mg–S battery to achieve an initial capacity exceeding 1000 mAh g−1 and extended cycling stability. These findings highlight the potential of Mg–Ca hybrid electrolytes and nanosized α‐MnO2‐modified separators in the development of high‐performance Mg–S batteries.
Organic battery electrode materials represent a sustainable alternative compared to most inorganic electrodes, yet challenges persist regarding their energy density and cycling stability. In this work, a new organic electrode material is described, which is obtained via ionothermal polymerization of low‐cost starting materials, melem (2,5,8‐triamino‐tri‐ s ‐triazine) and perylenetetracarboxylic dianhydride (PTCDA). The resulting networked polymer Melem‐PDI exhibits favorable thermal and electrochemical properties, prompting investigation into its performance as a positive electrode material in rechargeable lithium and magnesium batteries. A hybrid material with carbon nanotubes ( Melem‐PDI‐CNT ) is found to exhibit‐excellent cycling stability in Li‐ion batteries at a current rate as high as 500 mA g −1 for 5000 cycles. While the Li‐ion storage is based on a pseudocapacitive mechanism, a diffusion‐controlled mechanism is observed in magnesium batteries. This work underscores that classic dyes (here: PDI) can be repurposed for energy storage, once they are integrated into suitable polymer topologies and brought into nanoscale contact with conductive materials.