Constantin Carausu

Constantin Carausu

Auto-generated profile, based on publicly available information

Constantin Carausu

”Gheorghe Asachi” Technical University of Iasi, Department of Machine Manufacturing Technology, Blvd. Mangeron, No. 59A, 700050, Iasi, Romania

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 January 2022 in Processes
Verified
Journal Article
Open access
PDF file
IBIuliana Bejenari
Iuliana Bejenari
GHGabriela Hristea
Gabriela Hristea
CCConstantin Cărăușu
Constantin Cărăușu
Alice MijaAlice Mija
Alice Mija
Irina VolfIrina Volf
Irina Volf
In the context of sustainable use of resources, hydrothermal conversion of biomass has received increased consideration. As well, the hydrochar (the solid C-rich phase that occurs after the process) has caused great interest. In this work, spruce bark (Picea abies) wastes were considered as feedstock and the influence of hydrothermal process parameters (temperature, reaction time, and biomass to water ratio) on the conversion degree has been studied. Using the response surface methodology and MiniTab software, the process parameters were set up and showed that temperature was the significant factor influencing the conversion, while residence time and the solid-to-liquid ratio had a low influence. Furthermore, the chemical (proximate and ultimate analysis), structural (Fourier-transform infrared spectroscopy, scanning electron microscopy) and thermal properties (thermogravimetric analysis) of feedstock and hydrochar were analyzed. Hydrochar obtained at 280 °C, 1 h processing time, and 1/5 solid-to-liquid ratio presented a hydrophobic character, numerous functional groups, a lower O and H content, and an improved C matter, as well as a good thermal stability. Alongside the structural features, these characteristics endorsed this waste-based product for applications other than those already known as a heat source.

1 December 2020
Verified
Book Chapter
Closed access
PDF file
AMAndrei-Danut Mazurchevici
Andrei-Danut Mazurchevici
RPRamona-Iuliana Popa
Ramona-Iuliana Popa
CCConstantin Carausu
Constantin Carausu
SMSimona-Nicoleta Mazurchevici
Simona-Nicoleta Mazurchevici
Dumitru NedelcuDumitru Nedelcu
Dumitru Nedelcu

19 October 2022 in MATEC Web of Conferences
Verified
Journal Article
Open access
PDF file
AMAlina Marguta
Alina Marguta
SMSimona-Nicoleta Mazurchevici
Simona-Nicoleta Mazurchevici
CCConstantin Carausu
Constantin Carausu
Dumitru NedelcuDumitru Nedelcu
Dumitru Nedelcu
Coating of bio-based polymers with ceramic layer has attracted interest recently, the research topic raising difficulties regarding the technology of obtaining layers that involve very high working temperatures. The study aims to analyses the mechanical, tribological and structural characteristics of the Arboblend V2 Nature biodegradable polymer after the deposition of ceramic microlayers. The micro powders used were Amdry 6420 (Cr2O3), Metco 143 (ZrO2 18TiO2 10Y2O3) and Metco 136F (Cr2O3-xSiO2-yTiO2). The coated samples were obtained by injection molding and the deposition was achieved by using Atmospheric Plasma Spray (APS) method. The results of the related analyses showed that, in general, the deposits of ceramic micro particles increased the material surface characteristics (hardness, scratch resistance, apparent friction coefficient), due to the uniformity of the ceramic coating on the polymeric substrate. Based on these, it was possible to recommend the use of coated bio-based polymer - Arboblend V2 Nature in harsh operating conditions, such as the automotive industry.

16 July 2015 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
CCCărăuşu Constantin
Cărăuşu Constantin
SPSimona Plăvănescu
Simona Plăvănescu
Dumitru NedelcuDumitru Nedelcu
Dumitru Nedelcu

10 March 2025 in Journal of Engineering Sciences and Innovation
Verified
Journal Article
Closed access
MIMihaela Feraru Ilie
Mihaela Feraru Ilie
SMSimona-Nicoleta Mazurchevici
Simona-Nicoleta Mazurchevici
TMTeodor Daniel MÎndru
Teodor Daniel MÎndru
CCConstantin Carausu
Constantin Carausu
Dumitru NedelcuDumitru Nedelcu
Dumitru Nedelcu
Polymers in general have low tensile strength and modulus of elasticity, poor electrical conductivity, low thermal and erosion resistance and high sensitivity to ultraviolet (UV) radiation. A technique called polymer metallization (PM), whereby a metallic layer is deposited on the surface of polymer parts, mitigates these shortcomings and extends the applicability of polymers. There are various ways to metallise polymer surfaces. The most efficient ones are thermal spraying (TS), electroplating, chemical vapour deposition (CVD), and physical vapour deposition (PVD). The benefits of each of these approaches are listed below: The application range of PVD and CVD is constrained by workpiece size, shape, and productivity, and both processes entail significant equipment and processing expenses. Electroplating is limited by low adhesive strength and long production cycle, strongly linked to environmental risks/costs. The CVD method takes too long and wet processing conditions limit the range of possible applications. TS methods provide the highest deposition rate and are cheaper, greener and easier to implement in industry than other deposition methods. Of the TS methods, Cold Spray (CS) uses the lowest operational jet temperatures, does not pre-melt the metal particles for deposition, and limits the risks of metal powder oxidation and thermal damage to the substrate. Metals, alloys, polymers, ceramics, and composites can all be deposited with this method on a range of substrate materials. Other names for CS include supersonic particle deposition, kinetic sputtering, dynamic or kinetic metallisation, CS additive manufacturing (CSAM), and dynamic cold gas sputtering. The paper firstly presents a comparison between the main processing methods, after which different experimental results on the resulting microstructure, different mechanical and thermal properties of the copper-coated polymer composites are presented. All the aspects presented above are important from the point of view of the recommendations that can be made for the use of these copper-coated composites in different industrial fields.

18 September 2018 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
CTC G Turc
C G Turc
CCC Cărăuşu
C Cărăuşu
GBGeorge Belgiu
George Belgiu
The part cost optimization is one of the major problems in plastics industry. The designers must take into account a lot of aspects regarding the functional role of the part, the mechanical loads, and least but not last, the part cost. The part cost depends on the mould cost, the equipment operation cost and the material cost. The paper presents a methodology to estimate the part cost, focusing on the equipment operation cost. In addition, a spreadsheet is provided in order to estimate the equipment operation cost.