Teodor Daniel MÎndru

Dr. Teodor Daniel MÎndru

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 January 2023 in Polymers
Verified
Journal Article
Open access
PDF file
SMSimona-Nicoleta Mazurchevici
Simona-Nicoleta Mazurchevici
Oktawian BialasOktawian Bialas
Oktawian Bialas
TMTeodor Daniel MÎndru
Teodor Daniel MÎndru
Marcin AdamiakMarcin Adamiak
Marcin Adamiak
Dumitru NedelcuDumitru Nedelcu
Dumitru Nedelcu
Surface texturing is an engineering technology used in order to improve the surface characteristic of plastic parts obtained by injection molding. Applying this process not only changes the part surface properties, but also its topography. The novel functionalities of plastic products become useful when other materials make contact with the textured surface. Of course, these characteristics may vary depending on the laser positioning, dimensions, and geometry of the texture. The present paper presents the surface characteristics obtained after the laser texturing of the Arboblend V2 Nature biodegradable polymer. Three distinct geometries were studied: hexagonal, square, and triangular, and different behaviors of them were highlighted during surface free energy (SFE) and contact angle (WCA) measurements: a hydrophobic character for square and hexagonal geometry with distilled water as the measure liquid, and a hydrophilic character with diiodomethane as the measure liquid; for triangle geometry, the contact angle measurements were impossible to extract because the drop turns into a flat puddle. Additionally, the friction coefficient varied depending on the geometry texture, with the lowest value being recorded by the sample with hexagonal geometry. The micro-indentation tests highlighted increased surface micro-hardness compared to the basic material. The possibility of use in the practice of textured surfaces is viable; thus, based on the obtained results, there is even the possibility to replace non-biodegradable polymers from different sectors of activity.

19 February 2025 in Coatings
Verified
Journal Article
Open access
PDF file
PRPetronela Daniela Rusu
Petronela Daniela Rusu
Oktawian BialasOktawian Bialas
Oktawian Bialas
AWAnna Woźniak
Anna Woźniak
Marcin AdamiakMarcin Adamiak
Marcin Adamiak
Augustine Nana Sekyi AppiahAugustine Nana Sekyi Appiah
Augustine Nana Sekyi Appiah
Dumitru NedelcuDumitru Nedelcu
Dumitru Nedelcu
Surface texturing entails surface alteration through forming, microgrooving, microdimpling, and microchanneling. This is achieved by laser micromachining, in addition to other related methods, of a substrate surface. The present paper describes the surface characteristics obtained after the laser texturing of a biodegradable polymer (Arbofill Fichte) with four and six passes in hexagonal and square patterns. The results of the wettability test indicate that this biodegradable polymer has a surface with a weak hydrophobic characteristic (contact angle near 90°), regardless of the type of texture that is obtained. The underlying material’s wear behavior changes as a result of the surface alteration due to laser surface texturing (LST). The coefficient of friction (COF) values thus increase for all samples. The hexagonal geometry offers greater stability and consistency compared to square geometry, independent of the number of passes. Square geometry is more susceptible to variations, particularly along the Y axis, and may need additional adjustment of the process parameters. The hexagonal structure naturally promotes more uniform leveling due to its tighter and more evenly spread arrangement, even at four texturing passes (4x). However, at six texturing passes (6x), the advantages become more pronounced because of the repeated overlaps in the laser trajectories. The overlap in the hexagonal configuration guarantees that each area of the material receives a relatively consistent energy dose, reducing localized discrepancies. The possibility of using this method to texture surfaces is viable; thus, based on the obtained results, there is the possibility that it can replace non-biodegradable polymers in different sectors.

31 August 2025 in Micromachines
Verified
Journal Article
Open access
PDF file
CCCiprian Dumitru Ciofu
Ciprian Dumitru Ciofu
PRPetronela Daniela Rusu
Petronela Daniela Rusu
Marcin AdamiakMarcin Adamiak
Marcin Adamiak
Oktawian BialasOktawian Bialas
Oktawian Bialas
CTCatalin Nicolae Tampu
Catalin Nicolae Tampu
Dumitru NedelcuDumitru Nedelcu
Dumitru Nedelcu
Surface texturing involves creating micro-channels, micro-dimples, micro-grooving, and other surface modifications. To do this, laser and micromachining are employed on the substrate surface in addition to other methods. The surface characteristics of the Arboblend V2 Nature biodegradable polymers with laser texturing, hexagonal and square patterns, and four and six passes are shown in this study. Regardless of the texture type, Arboblend V2 Nature’s hydrophilic surface (a contact angle of less than 90°) was demonstrated by the results of the wettability test. The underlying material’s wear behavior changed as a result of the LST surface modification. The COF values increased only after six passes with both textures. On the topographical side, Arboblend V2 Nature (square and hexagonal) shows a consistent X-axis expansion in the hexagonal geometry and a considerable amount of variability in the square geometry, especially at six passes, where the Y-axis (higher depths) is more compressed. According to the results, since textured surfaces are practicable, non-biodegradable polymers from a variety of industries can be substituted.

10 March 2025 in Journal of Engineering Sciences and Innovation
Verified
Journal Article
Closed access
MIMihaela Feraru Ilie
Mihaela Feraru Ilie
SMSimona-Nicoleta Mazurchevici
Simona-Nicoleta Mazurchevici
TMTeodor Daniel MÎndru
Teodor Daniel MÎndru
CCConstantin Carausu
Constantin Carausu
Dumitru NedelcuDumitru Nedelcu
Dumitru Nedelcu
Polymers in general have low tensile strength and modulus of elasticity, poor electrical conductivity, low thermal and erosion resistance and high sensitivity to ultraviolet (UV) radiation. A technique called polymer metallization (PM), whereby a metallic layer is deposited on the surface of polymer parts, mitigates these shortcomings and extends the applicability of polymers. There are various ways to metallise polymer surfaces. The most efficient ones are thermal spraying (TS), electroplating, chemical vapour deposition (CVD), and physical vapour deposition (PVD). The benefits of each of these approaches are listed below: The application range of PVD and CVD is constrained by workpiece size, shape, and productivity, and both processes entail significant equipment and processing expenses. Electroplating is limited by low adhesive strength and long production cycle, strongly linked to environmental risks/costs. The CVD method takes too long and wet processing conditions limit the range of possible applications. TS methods provide the highest deposition rate and are cheaper, greener and easier to implement in industry than other deposition methods. Of the TS methods, Cold Spray (CS) uses the lowest operational jet temperatures, does not pre-melt the metal particles for deposition, and limits the risks of metal powder oxidation and thermal damage to the substrate. Metals, alloys, polymers, ceramics, and composites can all be deposited with this method on a range of substrate materials. Other names for CS include supersonic particle deposition, kinetic sputtering, dynamic or kinetic metallisation, CS additive manufacturing (CSAM), and dynamic cold gas sputtering. The paper firstly presents a comparison between the main processing methods, after which different experimental results on the resulting microstructure, different mechanical and thermal properties of the copper-coated polymer composites are presented. All the aspects presented above are important from the point of view of the recommendations that can be made for the use of these copper-coated composites in different industrial fields.

11 December 2024 in Preprints.org
Verified
Preprint
Open access
PDF file
PRPetronela Daniela Rusu
Petronela Daniela Rusu
Oktawian BialasOktawian Bialas
Oktawian Bialas
AWAnna Woźniak
Anna Woźniak
Marcin AdamiakMarcin Adamiak
Marcin Adamiak
CTCatalin Nicolae Tampu
Catalin Nicolae Tampu
Dumitru NedelcuDumitru Nedelcu
Dumitru Nedelcu
Surface texturing entails surface alteration through forming, micro grooving, micro dimpling and microchanneling. This is achieved by laser micromachining, in addition to other related methods on the substrate surface. The present paper puts forward the surface characteristics obtained after the laser texturing of the Arbofill Fichte biodegradable polymers with four and six passes, in hex-agonal and square patterns. The results of the wettability test indicated that Arbofill Fichte has a surface with a weak hydrophobic character (contact angle near 90°), regardless of the type of texture that was obtained. The underlying material's wear behaviour changed as a result of the Laser Surface Texturing (LST) surface alteration. Friction coefficient (COF) values thus increased for all samples. Arbofill Fichte exhibits a higher Y-axis stability in both geometries, suggesting a better resistance to vertical compression (subsidence), particularly in the 6 passes case. Addition-ally, Arbofill Fichte has a better X-axis extension. Therefore, Arbofill Fichte is stable and uniform in both geometries and at both numbers of passes, providing a more consistent X-axis expansion and better-managed Y-axis compression. The possibility of use in the practice of textured surfaces is viable; thus, based on the obtained results, there is even the possibility to replace non-biodegradable polymers from different sectors of activity.

29 December 2025 in Machines
Verified
Journal Article
Open access
PDF file
TMTeodor Daniel MÎndru
Teodor Daniel MÎndru
CCCiprian Dumitru Ciofu
Ciprian Dumitru Ciofu
SGStefan Grigorean
Stefan Grigorean
MMMarica Mariana
Marica Mariana
IDIlie Dumitru
Ilie Dumitru
Dumitru NedelcuDumitru Nedelcu
Dumitru Nedelcu
The design and construction of a racing car often involve determining the optimal technological solution and designing the subassemblies, taking into account the required specifications. The case presented in this paper details improvements to the fixture layout of a braking system using a floating disc, starting from the use of calipers and brake pads that are already available on the market, and the design, modeling, and manufacture of an optimal brake disc for car requirements. Based on their accumulated experience, the authors identified the cause of vibrations under certain braking conditions, as well as the causes leading to mechanical fatigue of the braking system components. Following the simulations, the design of the floating brake disc was improved and subsequently, a car equipped with this new type of brake disc was tested to analyze the behavior of the braking system. The results showed an improvement in the maneuverability of the car, a slower deterioration of the components of the braking system and a temperature reduction in the components during operation on the circuit.