Nicola Corna

Nicola Corna

Auto-generated profile, based on publicly available information

Nicola Corna

Dipartimento di Elettronica, Informazione e Bioingegneria (DEIB), Politecnico di Milano, Milan, Italy

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2021 in IEEE Access
Verified
Journal Article
Open access
Fabio GarzettiFabio Garzetti
Fabio Garzetti
NCNicola Corna
Nicola Corna
Nicola LusardiNicola Lusardi
Nicola Lusardi
AGAngelo Geraci
Angelo Geraci
The Field Programmable Gate Array (FPGA) structure poses several constraints that make the implementation of complex asynchronous circuits such as Time–Mode (TM) circuits almost unfeasible. In particular, in Programmable Logic (PL) devices, such as FPGAs, the operation of the logic is usually synchronous with the system clock. However, it can happen that a very high–performance specifications demands to abandon this paradigm and to follow an asynchronous implementative solution. The main driver forcing the use of programmable logic solutions instead of tailored Application Specific Integrated Circuits (ASIC), best suiting an asynchronous design, is the request coming from the research community and industrial R&D of fast–prototyping at low Non Recursive Engineering (NRE) costs. For instance in the case of a high–resolved Time–to–Digital Converter (TDC), a signal clocked at some hundreds of MHz implemented in FPGA allows implementing a TDC with resolution at ns. If a higher resolution is required, the signal frequency cannot be increased further and one of the aces up the designer’s sleeve is the propagation delay of the logic in order to quantize the time intervals by means of a so-called Tapped Delay–Line (TDL). This implementation of TDL–based TDC in FPGAs requires special attention by the designer both in making the best use of all available resources and in foreseeing how signals propagate inside these devices. In this paper, we investigate the implementation of a high–performance TDL–TDC addressed to 28–nm 7–Series Xilinx FPGA, taking into account the comparison between different technological nodes from 65–nm to 20–nm. In this context, the term high–performance means extended dynamic–range (up to 10.3 s), high–resolution and single–shot precision (up to 366 fs and 12 ps r.m.s respectively), low differential and integral non–linearity (up to 250 fs and 2.5 ps respectively), and multi–channel capability (up to 16).

15 September 2021 in IEEE Access
Verified
Journal Article
Open access
Nicola LusardiNicola Lusardi
Nicola Lusardi
NCNicola Corna
Nicola Corna
Fabio GarzettiFabio Garzetti
Fabio Garzetti
SSSimone Salgaro
Simone Salgaro
AGAngelo Geraci
Angelo Geraci
The enormous diffusion of Time-Mode circuits, in particular Time-to-Digital Converter (TDC) time measurement circuits, and at the same time the dizzying increase in parallel channels required by the most recent applications, for example in the automotive and digital imaging fields, brings the problem of electromagnetic interference between channels ever more to the fore. This phenomenon, generally known as Cross-Talk (XT), is particularly critical given the increase in the operating frequency and density of systems components, and its effect on the timing parameters in TDC measurements is investigated. Considering the time measurements, XT creates temporal shift on the physical events from which the timestamps are extracted; in this manner, an error in the measurements is generated. In order to detect the XT phenomena, a methodical analysis based on Code-Density Test (CDT) is performed; in this terms, two different typologies of XTs are investigated, which are correlated and uncorrelated XT. Furthermore, a TDC board is used as case study and all the XT sources are detected and classified. Thus, a classification of the importance of the different sources of XT is achived and a solution to minimize the different causes is proposed.

30 August 2021 in IEEE Access
Verified
Journal Article
Open access
NCNicola Corna
Nicola Corna
Fabio GarzettiFabio Garzetti
Fabio Garzetti
Nicola LusardiNicola Lusardi
Nicola Lusardi
AGAngelo Geraci
Angelo Geraci
We present a small, portable, plug–and–play time measurement instrument entirely based on Field Programmable Gate Array (FPGA). Its performance is state–of–the–art in terms of the most recent Application–Specific Integrated Circuit (ASIC) solutions of Time–to–Digital Converters (TDCs), and all operating features are fully–programmable. The instrument offers an excellent cost–performance and is suitable for detector test and time correlation measurement applications. More generally, the instrument is very well suited for fast–prototyping of systems where time measures are involved, at low cost and design effort. All the features of the instrument can be easily accessed through either the Graphical User Interface (GUI) or directly from the software Application Programming Interface (API).

11 August 2022 in IEEE Transactions on Instrumentation and Measurement
Verified
Journal Article
Closed access
Nicola LusardiNicola Lusardi
Nicola Lusardi
Fabio GarzettiFabio Garzetti
Fabio Garzetti
ACAndrea Costa
Andrea Costa
MCMarco Cautero
Marco Cautero
NCNicola Corna
Nicola Corna
AGAngelo Geraci
Angelo Geraci
We present an high-resolution 3D (X,Y,t) imager for time-resolved experiments based on time-to-space conversion. The system uses Cross Delay-Line detectors (CDL) for particle identification and a fully-configurable digital processor based on Field Programmable Gate Arrays (FPGAs) for the 3D image reconstruction. The instrument reaches a spatial resolution of 45 μm FWHM (i.e.,18 μm r.m.s.) and a temporal precision of 15 ps r.m.s.. The detection rate achieved is 10 Mcps, with a dead-time below 7 ns, leading to a global throughput up to 6 Gb/s. In addition to the state-of-the-art performance, the innovative aspect of the presented contribution resides in the complete reconfigurability of the instrument: it is, in fact, the first time that the Time-to-Digital Converter (TDC) used for the time-to-space conversion, has been fully implemented in programmable logic, without the use of dedicated Application Specific Integrated Circuit (ASIC) components. This advancement allows to adapt the instrument to the experimental setup without undergoing impractical hardware modifications.

22 April 2022 in IEEE Access
Verified
Journal Article
Open access
ACAndrea Costa
Andrea Costa
NCNicola Corna
Nicola Corna
Fabio GarzettiFabio Garzetti
Fabio Garzetti
Nicola LusardiNicola Lusardi
Nicola Lusardi
EREnrico Ronconi
Enrico Ronconi
AGAngelo Geraci
Angelo Geraci
In a world heading towards applications, in science and industry, based on big data processing, the ability to elaborate streams of data is becoming more important every day. Applications of various natures, ranging from biology to chemistry, from medical imaging to spectroscopy, need systems able to detect, process and store huge amounts of data in real-time. In this context, techniques such as histogramming come into play. Histograms are able to represent data shapes and retrieve statistical information, favoring further processing. This kind of processing is usually done with the help of general purpose processors, relying on temporal computing, with their pros (simplicity and fast operating frequencies) and cons (inability to exploit parallel computation). Both Industry and Academia have, however, proposed many solutions to this need, delivering histogram generators both in full-custom Application-Specific Integrated Circuits (ASICs) and Field-Programmable Gate Array (FPGA) IP-Cores, preferred over processors thanks to their superior parallel computing power. In this work, we present a full FPGA approach to this issue, resulting in a high-performance IP-Core for generating and managing multiple histograms in real time, each supporting a data flow up to 224 MSps, with a strong focus on overall flexibility and area efficiency, using as low as < 250 LUTs and 300 FFs resources for a 16 bit-wide, 4096-bin histogram implementation. The IP-Core has been successfully integrated and validated in a high-performance time-mode application: an FPGA-based Time-to-Digital Converter. The resulting IP-Core is, more in general, a single solution perfectly adaptable to any field of application and FPGA device.

27 July 2022 in IEEE Access
Verified
Journal Article
Open access
EREnrico Ronconi
Enrico Ronconi
NCNicola Corna
Nicola Corna
ACAndrea Costa
Andrea Costa
Fabio GarzettiFabio Garzetti
Fabio Garzetti
Nicola LusardiNicola Lusardi
Nicola Lusardi
AGAngelo Geraci
Angelo Geraci
Framing methods are used to break a data stream into packets in most digital communications. The use of a reserved symbol to denote the frame boundaries is a popular practice. This end-of-frame (EOF) marker should be removed from the packet content in a reversible manner. Many strategies, such as the bit and byte stuffing processes employed by high-level data link control (HDLC) and Point-to-Point Protocol (PPP), or the Consistent Overhead Byte Stuffing (COBS), have been devised to perform this goal. These bit and byte stuffing algorithms remove the reserved EOF marker from the packet payload and replace it with some extra information that can be used to undo the action later. The amount of data added is called overhead and is a figure-of-merit of such algorithms, together with the encoding and decoding speed. Multi-COBS, a new byte stuffing algorithm, is presented in this paper. Multi-COBS provides concurrent encoding and decoding, resulting in a performance improvement of factor four or eight in common word-based digital architectures while delivering an average and worst-case overhead equivalent to the state-of-the-art. On the reference 28-nanometer field programmable gate array (FPGA) (Artix-7), Multi-COBS achieves a throughput of 6.6 Gbps, instead of 1.7 Gbps of COBS. Thanks to its parallel elaboration capability, Multi-COBS is ideal for digital systems built in programmable logic as well as modern computers.