Arvid Abel

Arvid Abel

Auto-generated profile, based on publicly available information

Arvid Abel

Additive Manufacturing Department Laser Zentrum Hannover e.V. Hollerithallee 8 30419 Hannover Germany

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 February 2021 in Materials
Verified
Journal Article
Open access
PDF file
SJStefan Julmi
Stefan Julmi
AAArvid Abel
Arvid Abel
NGNiklas Gerdes
Niklas Gerdes
CHChristian Hoff
Christian Hoff
JHJörg Hermsdorf
Jörg Hermsdorf
HMHans Maier
Hans Maier
Additive manufacturing (AM) has become increasingly important over the last decade and the quality of the products generated with AM technology has strongly improved. The most common metals that are processed by AM techniques are steel, titanium (Ti) or aluminum (Al) alloys. However, the proportion of magnesium (Mg) in AM is still negligible, possibly due to the poor processability of Mg in comparison to other metals. Mg parts are usually produced by various casting processes and the experiences in additive manufacturing of Mg are still limited. To address this issue, a parameter screening was conducted in the present study with experiments designed to find the most influential process parameters. In a second step, these parameters were optimized in order to fabricate parts with the highest relative density. This experiment led to processing parameters with which specimens with relative densities above 99.9% could be created. These high-density specimens were then utilized in the fabrication of test pieces with several different geometries, in order to compare the material properties resulting from both the casting process and the powder bed fusion (PBF-LB) process. In this comparison, the compositions of the occurring phases and the alloys’ microstructures as well as the mechanical properties were investigated. Typically, the microstructure of metal parts, produced by PBF-LB, consisted of much finer grains compared to as-cast parts. Consequently, the strength of Mg parts generated by PBF-LB could be further increased.

29 November 2024 in Acta Astronautica
Verified
Journal Article
Open access
TGTjorben Griemsmann
Tjorben Griemsmann
JPJoel Patzwald
Joel Patzwald
CCChetan Chawda
Chetan Chawda
TETim Eismann
Tim Eismann
AAArvid Abel
Arvid Abel
LOLudger Overmeyer
Ludger Overmeyer

24 May 2024 in Progress in Additive Manufacturing
Verified
Journal Article
Open access
PDF file
AAArvid Abel
Arvid Abel
ASAnutsek Sharma
Anutsek Sharma
HHHannes Holländer
Hannes Holländer
DZDawn Zheng
Dawn Zheng
NENicole Emminghaus
Nicole Emminghaus
SKStefan Kaierle
Stefan Kaierle
Due to the improved understanding of the industry, additive manufacturing processes are becoming increasingly accepted for fabricating complex lightweight components. The focus of the magnesium research is primarily on small implant structures. Due to challenges in the manufacturing process and oxidation behavior, large structures for lightweight components are mainly fabricated with titanium. This paper expands the scope of the laser-based powder bed fusion (PBF-LB) of larger-area magnesium parts with surface enhancement using the Ultraceramic® by the plasma electrolytic oxidation (PEO). For this purpose, the PBF-LB process development for cylindric structures with a diameter of 31 mm is carried out. The processing strategies are adapted for a crack and porosity free process. To mitigate the inherent oxidation of the biodegradable WE43 and reduce the surface wear in tribologically challenging applications, the additively manufactured magnesium is modified by the Ultraceramic®. The thickness of the ceramic surface could be tailored between 10 and 40 µm, while enclosing adhering powder particles of the PBF. Electrochemical impedance spectroscopy showed an increased resistance to corrosion by an increased modulus |Z0.01| by a factor of 658. The tribological behavior was characterized in pin-on-disc experiments and showed a decrease of surface wear down to 7.9 × 10–6 mm3/N·m up to a Hertzian pressure of 720 MPa tested by a tungsten carbide ball. Therefore, the synthesis of the PBF-LB of large-area magnesium parts and the PEO of the Ultraceramic® enables lightweight components for challenging oxidative and tribological conditions in real world applications.

23 February 2025 in Advanced Engineering Materials
Verified
Journal Article
Open access
AAArvid Abel
Arvid Abel
EBElmar Jonas Breitbach
Elmar Jonas Breitbach
HHHannes Holländer
Hannes Holländer
MMMichael Müller
Michael Müller
TGTjorben Griemsmann
Tjorben Griemsmann
LOLudger Overmeyer
Ludger Overmeyer
Additive manufacturing of magnesium alloys shows great potential for producing patient‐specific resorbable implants or lightweight parts. However, due to the reactive behavior, especially in the laser‐based powder bed fusion (PBF‐LB) fabrication process, the processing window to manufacture almost pore‐free parts is narrow compared to other materials such as titanium or steel. This article investigates optimal processing conditions for the PBF‐LB/M of WE43. To reduce the reactivity of the magnesium melt by limiting the interaction with remaining oxygen, a 3 vol% hydrogen admixture to the argon inert gas is investigated. Furthermore, long‐duration heat treatments are investigated in the range of 250–350 °C for 48 h. This study evaluates the impact of both methods on mechanical properties and microstructure. Although hydrogen seems to have no significant influence on the relative density, the microstructure, and the phase composition, it can slightly increase the tensile strength and elongation at break in the as‐built state. A heat treatment of 250 °C can increase the elongation at the break without impeding the tensile strength.

1 December 2024 in Advanced Engineering Materials
Verified
Journal Article
Open access
EBElmar Jonas Breitbach
Elmar Jonas Breitbach
SJStefan Julmi
Stefan Julmi
SBSabine Behrens
Sabine Behrens
TBTatiana Blank
Tatiana Blank
AAArvid Abel
Arvid Abel
HMHans Maier
Hans Maier
Magnesium alloys pose challenges in additive manufacturing, due to the difference between the melting temperature of magnesium oxide (2825 °C) on the powder particles and the boiling point of metallic magnesium (1093 °C). A promising approach to overcoming the difficulties is the reduction of the thickness of the high‐melting oxide layer on the surface of the particles. Magnesium alloys, each containing varying amounts of strontium, neodymium, and yttrium, are cast and subsequently analyzed in terms of their microstructures, mechanical properties, oxide layer thicknesses, and corrosion behavior. Alloying magnesium with strontium results in a reduction of the oxide layer thickness, which reaches a minimum of 0.5 wt% strontium content. The presence of rare earth elements increases the strength of the alloys, although the inclusion of neodymium results in an increase in the oxide layer thicknesses. On the other hand, the oxide layer thickness remains unaffected when alloying with yttrium. However, further increases in strontium content up to the monolithic phase Mg17Sr2 have been found to result in a reduced effect on the open‐circuit potential. Further studies should be conducted to investigate the suitability of strontium as an alloying element to reduce the oxide layer thickness of magnesium particles.

6 June 2026 in Optics & Laser Technology
Verified
Journal Article
Closed access
AAArvid Abel
Arvid Abel
ASAnutsek Sharma
Anutsek Sharma
TBTill Biermann
Till Biermann
SSSebastian Stammkötter
Sebastian Stammkötter
SSSteffen Sowka
Steffen Sowka
SKStefan Kaierle
Stefan Kaierle