5 August 2024 in npj Materials Degradation
Slow strain rate tensile testing was conducted on electrodeposited copper, which is a candidate coating material for used nuclear fuel containers. Embrittlement was observed in electrodeposited copper containing 26.4 ± 1.0 ppm hydrogen, with a strain rate sensitivity such that the embrittlement was exacerbated at lower strain rate (5 × 10−7 s−1). Tensile tests conducted at 100° and 200 °C also intensified embrittlement when compared with tests conducted at room temperature. In contrast, electrodeposited copper containing only 5.25 ± 0.97 ppm hydrogen exhibited ductile behavior at all tested strain rates and temperatures. These findings suggest that a previously unexplained slow strain rate hydrogen embrittlement can operate in electrodeposited copper provided that the hydrogen concentration is sufficiently high. Further analyses revealed that the deformation of embrittled copper is achieved by the formation of internal microcracks which coalesce at the point of failure.
2 April 2025 in Corrosion Science
2 May 2026 in npj Materials Degradation
In part I of this study, a previously unexplained form of hydrogen embrittlement and strain rate sensitivity was observed in electrodeposited copper. Here, the authors explored the dynamics of retained hydrogen in electrodeposited copper. Thermal desorption analyses were performed to characterize hydrogen trap energies of 0.39 ± 0.05, 0.63 ± 0.04, and 1.1 ± 0.04 eV. Annealing was conducted to evaluate the possibility of baking out hydrogen from electrodeposited copper and restoring ductility. A new electrodeposited material which is a candidate for coating used nuclear fuel containers was synthesized using tailored electrodeposition parameters, resulting in only 3.03 ± 0.58 ppm hydrogen, as compared to 26.4 ± 1.0 ppm. The mobility of hydrogen as it relates to embrittlement is discussed, and it is proposed that only hydrogen stored in low-energy trap sites contributes to embrittlement.
15 December 2025 in Corrosion
Grain boundary borides were detected in model Ni-Cu-B alloys by nano-scale secondary ion mass spectrometry, transmission electron microscopy, and x-ray diffractometry. Boron enrichment at grain boundaries was also observed in commercially available Monel 400. Potentiostatic corrosion experiments showed that intergranular attack occurred in Ni-Cu alloys containing 100 or 1000 ppm boron, and in commercially available Monel 400, while no intergranular attack was observed in a pure Ni-Cu alloy. The existence of grain boundary borides is believed to be the cause of intergranular attack observed in ex-service nuclear steam generator tubing made of Monel 400.
3 November 2026 in Materials and Corrosion
The present work investigates the tensile behavior of a copper coating electrodeposited onto steel that had been prepared in an acid bath after heat treatment. The copper is brittle at slow strain rates (1 × 10 −6 s −1 ) but ductile at fast strain rates (1 × 10 −3 s −1 ). A uniform distribution of tiny cavities is observed throughout the material after electrodeposition. Microstructural and chemical composition characterizations demonstrate that annealing the electrodeposited copper at 600°C increases grain size and transitions the morphology adjacent to the copper‐steel deposition interface from lamellar to equiaxed. Approximately 32% of the initial 17.8 ± 4.0 wppm hydrogen content is released by the 600°C annealing. Nano‐analysis of annealed samples shows the redistribution and the coalescence of cavities at grain boundaries, twins, and dislocations. Slow strain rate (1 × 10 −6 s −1 ) tensile tests of 600°C annealed samples still show a significant strain rate sensitivity, similar to the non‐heat‐treated material, and only a small improvement in ductility. Redistribution of solute hydrogen atoms on dislocations during annealing is hypothesized to be the reason behind this phenomenon.