Ziyue Yang

Ziyue Yang

Auto-generated profile, based on publicly available information

Ziyue Yang

China University of Mining and Technology

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 April 2024 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
ASAnran Sun
Anran Sun
Chenyang XiaChenyang Xia
Chenyang Xia
YCYuhang Chen
Yuhang Chen
YLYunhai Liu
Yunhai Liu
ZYZiyue Yang
Ziyue Yang
ZYZijian Yang
Zijian Yang
Aiming at the problems that existing multifrequency and multiload (MFML) magnetic coupling resonant wireless power transfer (MCR-WPT) systems either the output power frequencies are limited, or a large amount of reactive power in them leads to decrease power factor (PF), this paper proposes a MFML MCR-WPT system based on hysteresis current (HC) control, which controls multifrequency current superposition output and has equivalent current source characteristics. The system outputs multifrequency current by tracking the command current, which consists of subcommand currents designed according to load frequency and power requirements and raises PF without affecting power transfer quality by adding power compensating capacitor (CP) with lower cost and design complexity than existing technologies. Firstly, the system structure and working principle are introduced. Then, the criterion of equivalent current source is deduced, based on which the system model is established, and its characteristics are analyzed. After that, the system parameter design methods are given. Finally, an experimental platform is built to verify the proposed theory. The simulation and experimental results show that the proposed system can output multifrequency power and switch the frequency freely and raise PF by adding Cp without affecting power transfer

23 January 2024 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
ZYZiyue Yang
Ziyue Yang
Chenyang XiaChenyang Xia
Chenyang Xia
SZShuze Zhao
Shuze Zhao
HLHao Lu
Hao Lu
CHChao Hu
Chao Hu
XHXing Huang
Xing Huang
Wireless power transfer technology is widely used for wireless electric vehicle chargers (WEVC) due to its safety, flexibility, and convenience. However, there is an inevitable misalignment between the transmitter and receiver of WEVC, which reduces the efficiency and stability of power transfer significantly. To this end, this article proposes a receiver position detection (PD) system based on the novel active beacon structure to improve the transfer performance of WEVCs. First, the novel beacons are activated to detect the receiver misalignment accurately before power transfer, which are placed on the vehicle side. Meanwhile, the PD coil matrix is employed on the ground side to achieve large-area and precise misalignment detection. Then, the parameters of PD circuits are optimized to reduce the sampled voltage errors correspondingly. In addition, with the aid of the proposed system structure, a weighted centroid PD algorithm is given to calculate the position of the receiver. Finally, the feasibility of the proposed PD system is verified by using an experimental prototype. The experimental results achieve an offset detection accuracy of 3 mm in the area of 600 mm×480 mm and a yaw angle detection accuracy of 2 $^{\circ }$ in the area of 120 mm×480 mm.

21 April 2025 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
ZYZiyue Yang
Ziyue Yang
Chenyang XiaChenyang Xia
Chenyang Xia
ASAnran Sun
Anran Sun
XWXirui Wang
Xirui Wang
SZShuze Zhao
Shuze Zhao
Feng LiFeng Li
Feng Li
Accurate detection of metal objects (MO) and live objects (LO) is essential to ensure the safe operation of wireless electric vehicle chargers. This letter proposes a dual-mode foreign object detection (FOD) system. The system utilizes the time division multiplexing mode to detect foreign objects and the frequency sweeping resonance mode to distinguish between MOs and LOs. First, a bipolar overlapping FOD coil is introduced and the effects of MOs and LOs on the coil impedance are analyzed. Subsequently, details regarding the design, operational principles, and detection criteria of the proposed dual-mode FOD system are provided. Finally, the proposed methods are verified with experimental results. The results indicate that a 30 mm diameter aluminum sheet causes a 0.06 V reduction in sampling voltage and a 20 kHz increase in resonance frequency, while a human finger induces a 0.18 V reduction in sampling voltage and a 180 kHz decrease in resonance frequency. These findings confirm the feasibility and effectiveness of the proposed system and its detection criteria.

25 June 2024 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
Chenyang XiaChenyang Xia
Chenyang Xia
CLChenhao Lu
Chenhao Lu
SZShuze Zhao
Shuze Zhao
ZYZiyue Yang
Ziyue Yang
YCYuheng Cao
Yuheng Cao
YGYuxiang Gao
Yuxiang Gao
Metal object detection (MOD) and living object detection (LOD) are essential for ensuring the safe operation of the electric vehicle (EV) wireless charging system. Since most MOD or LOD single-type systems protect the EV wireless charging system incomprehensively, the existing MOD and LOD shared system has problems such as difficulty in acquiring detection signal, and low accuracy for small-sized living objects (LOs). Thus, this article proposes a planar double-winding foreign object detection (FOD) system based on the time-division multiplexing control strategy. First, the planar double-winding FOD system structure is given, and the time-division multiplexing FOD mode switching as well as FOD judgement principle are analyzed. Second, the phase variation of bandpass filter output voltage in the planar double-winding FOD system is analyzed. Third, the sensing coil structure and detecting circuit parameters are optimized. Finally, an experimental platform is built to verify the feasibility. The results show that when MOD and LOD phase thresholds are set to 3 $^{\circ }$ and 20 $^{\circ }$ , respectively, the phase variation is −21.3 $^{\circ }$ , −27.9 $^{\circ }$ , −7 $^{\circ }$ , and 48.3 $^{\circ }$ for a copper plate, aluminum plate, iron plate of 40 × 40 mm 2 and one hand. Therefore, the phase variation is larger than the phase threshold, which can effectively detect MO and LO.

29 November 2023 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
SZShuze Zhao
Shuze Zhao
Chenyang XiaChenyang Xia
Chenyang Xia
ZYZiyue Yang
Ziyue Yang
HLHaipan Li
Haipan Li
YCYuheng Cao
Yuheng Cao
Metal object detection (MOD) technology can effectively improve the safety of wireless charging systems for electric vehicles. To solve the problem of disunity in sensitivity evaluation methods and the lack of parameters design rules in the research field of MOD technology, a sensitivity evaluation model for MOD systems based on sensing coils is constructed and three system parameters design rules are proposed based on this model. First, a sensitivity evaluation factor is defined and different types of detection blind spot generation mechanisms are distinguished. Second, three parameters design rules are obtained: parameters design rules for high sensitivity, parameters design rules for low detection voltage errors, and parameters design rules for reducing Rx coil impact. Third, the parameters design rules are verified and modified by electromagnetic field simulation. Three engineering parameters design rules for the bipolar checkerboard MOD system are obtained. Finally, a bipolar checkerboard MOD system is built to test different materials and sizes of metal objects (MOs). The eddy current dividing MOs capability and the advantage of high sensitivity of the bipolar checkerboard MOD system are verified.

2 October 2024 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
SZShuze Zhao
Shuze Zhao
Chenyang XiaChenyang Xia
Chenyang Xia
CLChenhao Lu
Chenhao Lu
ZYZiyue Yang
Ziyue Yang
ASAnran Sun
Anran Sun
Metal object detection (MOD) is an important part of wireless charging system for electric vehicles. To focus on the problem of detection blind zone caused by material parameters and the method of foreign object-type identification, an identification method of metal object (MO) types using high and low frequencies detection is proposed. First, the effects of electrical and magnetic permeability on the excitation magnetic field of MOD are analyzed, and a detection sensitivity model for all types of MO is constructed. Second, a detection blind spot caused by the material parameters of ferromagnetic metals is found, the detection blind spot frequency is defined and the mechanism of the blind spot is explained. Third, the identification principle of MO types by high and low frequencies is analyzed. The relationship between the sensitivity and the material parameters of ferromagnetic metals is simulated, and the blind spot detection frequency is 19 kHz when an iron of size 40 × 40 mm 2 is placed at the center of a checkerboard grid. Finally, an experimental platform for MO-type identification by high and low frequency detection is built, and it successfully identifies ferromagnetic metals, nonferromagnetic metals and ferrites.