15 September 2018 in International Journal of Engineering & Technology
The results of the investigation of the turning kinematics of the steerable wheels of the KrAZ-7634NE off-road vehicle with a wheel formula 8x8 and two front steer axles are given. The theoretical relations between the steer angles of the steerable wheels on the basis of the scheme of double-axle steering turning of the vehicle are shown. The mathematical model of flat four-bar vehicle steering linkage is developed, it determines the relation between the steering linkage left and right steering arms turning angles at any turning radius of the vehicle. KrAZ-7634HE steering three-dimensional model was created and simulation technique of its work was carried out using Creo software. It has been shown that the flat steering linkage model provides sufficient accuracy of calculations in analysis of turning kinematics. The design data can be used for any vehicles that have a similar steering linkage, they allow to analyze the impact of the vehicle design parameters on the turning kinematics and optimize them. Further study of the impact of the kingpin inclinations on the steering linkage kinematic and power characteristics are required.
20 March 2020 in Avtoshliakhovyk Ukrayiny
In any economy there is a need for the bulky goods transportation which cannot be divided into smaller parts. Such cargoes include building structures, elements of industrial equipment, tracked or wheeled construction and agricultural machinery, heavy armored military vehicles. In any case, tractor-semitrailer should provide fast delivery of goods with minimal fuel consumption. In order to guarantee the goods delivery, tractor-semitrailers must be able to overcome the existing roads broken grade and be capable to tow a semi-trailer in off-road conditions. These properties are especially important for military equipment transportation. The important factor that determines a tractor-semitrailer mobility is its gradeability. The purpose of this work is to improve a tractor-semitrailer mobility with tractor units manufactured at PJSC “AutoKrAZ” by increasing the tractor-semitrailer gradeability. The customer requirements for a new tractor are determined by the maximizing the grade to 18°. The analysis of the characteristics of modern tractor-semitrailers for heavy haulage has shown that the highest rate of this grade is 16.7°. The factors determining the limiting gradeability value were analyzed, based on the tractor-semitrailer with a KrAZ-6510TE tractor and a semi-trailer with a full weight of 80 t. It has been developed a mathematical model to investigate the tractor and semi-trailer axles vertical reactions distribution on the tractor-semitrailer friction performances. The mathematical model has allowed to calculate the gradeability value that the tractor-semitrailer can overcome in case of wheels and road surface friction value and the tractive force magnitude from the engine. The mathematical model adequacy was confirmed by comparing the calculations results with the data of factory tests. The analysis showed that on a dry road the KrAZ-6510TE tractor with a 80 t gross weight semitrailer is capable to climb a gradient of 14,35 ° with its coupling mass full use condition. The engine's maximum torque allows the tractor-semitrailer to overcome a gradient of 10.45° It has been determined the ways to improve the design of the KrAZ-6510TE tractor to increase its gradeability. Keywords: tractor, tractor-semitrailer vehicle mobility, tractor-semitrailer vehicle gradeability.
19 November 2025 in СУЧАСНІ ТЕХНОЛОГІЇ В МАШИНОБУДУВАННІ ТА ТРАНСПОРТІ
On modern electric vehicles, the traction battery is installed from below on the bottom of the body, which reduces the height of the vehicle's center of gravity and improves the vehicle's lateral stability during curved movement. The disadvantage of this arrangement is the increased risk of damage and destruction of the protective housing and, accordingly, the battery's electrical elements, which are dozens of ordinary household lithium-ion batteries of the AAA type. But the housings of these electrical elements are manufactured using a special technology that helps increase the strength of the housing and from a material with high heat dissipation. It is shown that the traction battery is the most expensive component of an electric vehicle. Therefore, the development of production methods aimed at increasing its service life is an urgent task. The mechanical characteristics of anisotropic material were taken into account during the manufacture of reinforced containers for electrical element housings. Data were determined that reliably reflect the influence of the stretching coefficient, planar anisotropy and the initial diameter of the work piece on the critical thickness of its plate. An expression was obtained that takes into account all the characteristics of the technological process that affect the thickness of the initial work piece. This allows you to control these characteristics in order to optimize the thickness of the work piece. The dependence obtained as a result of the study allows you to accurately and qualitatively calculate the optimal thickness of the initial work piece at the stage of developing the technological process for manufacturing battery cell housings for electric vehicles. Key words: electric car, lithium-ion battery, battery protection, anisotropic materials.
31 December 2024 in Avtoshliakhovyk Ukrayiny
KUKremenchuk Mykhailo Ostrohradskyi National University
Kremenchuk Mykhailo Ostrohradskyi National University
Calculations were made on the strength of the hot-rolled channel made of low-alloy steel produced by the metallurgical plant “Metinvest” (Ukraine) and the lightweight cold-bent channel made of high-strength steel produced by the metallurgical plant “Voestalpine AG” (Austria) for the frame spars of a heavy-duty vehicle – the KrAZ-6510TE tractor unit, as the most powerful and a loaded car from the model range of KrAZ cars, with the determination of stresses in the spars and critical zones under the condition of strength and magnitude of the spars’ bending deformation from static loads and. The calculations were carried out taking into account the chemical composition and mechanical properties of the materials, the geometric characteristics of the cross-sections of the channels by computer modeling with visualization of the determined stresses and critical zones in the spars. The study of loads on the frame was carried out according to the methodology of determining the static load on the frame of a stationary car from the sprung masses of hinged units and aggregates, which is then multiplied by the dynamism coefficient, which takes into account the increase in the load on the frame depending on road conditions and the speed of the car. The stress distribution in the frame spars was determined according to the IV theory of strength (ac-cording to Mises). Conclusions were made about the expediency of using lightweight cold-bent channels made of high-strength steel for the manufacture of frame spars of KrAZ heavy-duty trucks, as a result of which the strength and reliability of the frames is ensured with a significant saving of metal. Recommendations are provided for strengthening frame spars in critical areas. Research results can be applied to all models of KrAZ trucks. Keywords: truck, vehicle supporting system, frame strength, frame spars, channel profile, low-alloy steel, spar stress, spar deflection.