17 December 2018 in Nature Geoscience
1 January 2018 in Earth and Planetary Science Letters
6 August 2013 in Journal of Applied Physics
Standard nonlinear ultrasonic methods such as wave frequency mixing or resonance based measurements allow one to extract average, bulk variations of modulus and attenuation versus strain level. In contrast, dynamic acousto-elasticity (DAE) provides the elastic behavior over the entire dynamic cycle including hysteresis and memory effects, detailing the full nonlinear behavior under tension and compression. In this work, we address experimental difficulties and apply new processing methods, illustrating them with a Berea sandstone sample. A projection procedure is used to analyze the complex nonlinear signatures and extract the harmonic content. Amplitude dependences of the harmonic content are compared with existing models. We show that a combination of classical and hysteretic nonlinear models capture most of the observed phenomena. Some differences between existing models and experimental data are highlighted, however. A progressive decrease of the power-law amplitude dependence is found for harmonics larger than the second and for strains larger than 10−6. This observation is related to the phenomenon of acoustic conditioning that brings the material to a metastable state for each new excitation amplitude. Analysis of the steady-state regime provides additional information regarding acoustic conditioning, i.e., a progressive decrease of the amplitude of odd harmonics during excitation time with a log(t)-dependence. This observation confirms that the harmonic content is affected by the conditioning. Experimental challenges addressed include the fact that the compressional mode used for DAE can be affected by bending/torsion modes: their influence is evaluated, and guidances are given to minimize effects.
7 December 2018 in Water Resources Research
The evolution of frictional strength, stability, and fracture permeability is intimately linked both to the seismic cycle and to the impact of hydraulic stimulation for fractured reservoirs. However, despite this importance, the poromechanical relationships between fault permeability and strength remain unclear. The present study explores this relationship via laboratory experiments for concurrent shear‐flow on smooth fractures of Westerly granite. The novelty of these experiments is that the shear velocity is precisely controlled during the measurement of fracture permeability. Results indicate permeability enhancement during velocity‐weakening (potentially unstable) frictional slip. To decipher key processes contributing to this response, we evaluate the state of contacting asperities and of fracture surface asperities via digital rock fracture modeling of statistically equivalent surfaces. We propose two plausible mechanisms constraining the relationship between friction and permeability evolution—one based on changes in asperity contact distribution and one on shear‐induced dilation triggered by changes in fault slip velocity. These mechanisms should be taken into account in interpreting field observation such as the abrupt permeability increase of natural faults at the onset of seismic slip.
25 February 2015 in Journal of Geophysical Research: Solid Earth
Dynamic acoustoelastic testing is performed on a set of six rock samples (four sandstones, one soapstone, and one granite). From these studies at 20 strain levels 10−7<ϵ<10−5, four measures characterizing the nonlinear elastic response of each sample are found. Additionally, each sample is tested with nonlinear resonant ultrasonic spectroscopy and a fifth measure of nonlinear elastic response is found. These five measures of the nonlinear elastic response of the samples (approximately 3 × 6×20 × 5 numbers as each measurement is repeated 3 times) are subjected to careful analysis using model‐independent statistical methods, principal component analysis, and fuzzy clustering. This analysis reveals differences among the samples and differences among the nonlinear measures. Four of the nonlinear measures are sensing much the same physical mechanism in the samples. The fifth is seeing something different. This is the case for all samples. Although the same physical mechanisms (two) are operating in all samples, there are distinctive features in the way the physical mechanisms present themselves from sample to sample. This suggests classification of the samples into two groups. The numbers in this study and the classification of the measures/samples constitute an empirical characterization of rock nonlinear elastic properties that can serve as a valuable testing ground for physically based theories that relate rock nonlinear elastic properties to microscopic elastic features.
1 November 2011 in The Journal of the Acoustical Society of America
The aim is to assess the nonclassical component of material nonlinearity in several classes of materials with weak, intermediate, and high nonlinear properties. In this contribution, an optimized nonlinear resonant ultrasound spectroscopy (NRUS) measuring and data processing protocol applied to small samples is described. The protocol is used to overcome the effects of environmental condition changes that take place during an experiment, and that may mask the intrinsic nonlinearity. External temperature fluctuation is identified as a primary source of measurement contamination. For instance, a variation of 0.1 °C produced a frequency variation of 0.01%, which is similar to the expected nonlinear frequency shift for weakly nonlinear materials. In order to overcome environmental effects, the reference frequency measurements are repeated before each excitation level and then used to compute nonlinear parameters. Using this approach, relative resonant frequency shifts of 10−5 can be measured, which is below the limit of 10−4 often considered as the limit of NRUS sensitivity under common experimental conditions. Due to enhanced sensitivity resulting from the correction procedure applied in this work, nonclassical nonlinearity in materials that before have been assumed to only be classically nonlinear in past work (steel, brass, and aluminum) is reported.