Keji Yang

Keji Yang

Auto-generated profile, based on publicly available information

Keji Yang

State Key Laboratory of Fluid Power and Mechatronic Systems, College of Mechanical Engineering, Zhejiang University, Hangzhou, China

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 March 2019 in Sensors
Verified
Journal Article
Open access
PDF file
FLFuzai Lv
Fuzai Lv
PZPengfei Zhang
Pengfei Zhang
ZTZhifeng Tang
Zhifeng Tang
YYYonggang Yue
Yonggang Yue
KYKeji Yang
Keji Yang
Aluminum conductor steel-reinforced (ACSR) cables are typically used in overhead transmission lines, requiring stringent non-destructive testing owing to the severe conditions they face. Ultrasonic guided wave inspection provides promising online monitoring of the wire breakage of cables with the advantages of high sensitivity, long-range inspection, and full cross-sectional coverage. It is a very popular method to generate and receive guided waves using magnetostrictive and piezoelectric transducers. However, uniformly coupling the acoustic energy excited by transducers into multi-wire structures is always a challenge in the field application of guided waves. Long-term field application of piezoelectric transducers is limited due to the small coupling surface area, localized excitation, and couplant required. Conventional magnetostrictive transducers for steel strand inspection are based on the magnetostrictive effect of the material itself. Two factors affect the transducing performance of the transducers on ACSR cables. On one hand, there is a non-magnetostrictive effect in aluminum wires. On the other hand, the magnetostriction of the innermost steel wires is too weak to generate guided waves. The bias magnetic field is attenuated by the outer layers of aluminum wires. In this paper, an alternative sprayed magnetostrictive powder coating (SMPC) transducer was developed for guided wave generation and detection in ACSR cables. The Fe83Ga17 alloy powder with large magnetostriction was sprayed uniformly on the surfaces of certain sections of the outermost aluminum wires where the transducer would be installed. Experimental investigations were carried out to generate and receive the most commonly used L(0,1) guided waves for wire breakage detection at frequencies of 50 and 100 kHz. The results demonstrate that the discernable reflected waves of the cable end and an artificial defect of three-wire breakage (5.5% reduction in the cable’s cross-sectional area) were received by the transducer with SMPC, which was impossible for the transducer without SMPC. This method makes long-term and online monitoring of ACSR cables feasible due to the high coupling efficiency and good structural surface adaptability.

26 January 2024 in Nature Communications
Verified
Journal Article
Open access
PDF file
YWYunjiang Wang
Yunjiang Wang
XHXinben Hu
Xinben Hu
LCLuhang Cui
Luhang Cui
XXXuan Xiao
Xuan Xiao
KYKeji Yang
Keji Yang
HJHaoran Jin
Haoran Jin
Handheld robots offer accessible solutions with a short learning curve to enhance operator capabilities. However, their controllable degree-of-freedoms are limited due to scarce space for actuators. Inspired by muscle movements stimulated by nerves, we report a handheld time-share driven robot. It comprises several motion modules, all powered by a single motor. Shape memory alloy (SMA) wires, acting as “nerves”, connect to motion modules, enabling the selection of the activated module. The robot contains a 202-gram motor base and a 0.8 cm diameter manipulator comprised of sequentially linked bending modules (BM). The manipulator can be tailored in length and integrated with various instruments in situ, facilitating non-invasive access and high-dexterous operation at remote surgical sites. The applicability was demonstrated in clinical scenarios, where a surgeon held the robot to conduct transluminal experiments on a human stomach model and an ex vivo porcine stomach. The time-share driven mechanism offers a pragmatic approach to build a multi-degree-of-freedom robot for broader applications.

9 April 2019 in Applied Sciences
Verified
Journal Article
Open access
PDF file
JWJianjun Wu
Jianjun Wu
ZTZhifeng Tang
Zhifeng Tang
KYKeji Yang
Keji Yang
FLFuzai Lv
Fuzai Lv
Magnetostrictive patch transducers (MPT) with planar coils are ideal candidates for shear mode generation and detection in pipe and plate inspection with the advantages of flexibility, lightness and good directivity. However, the low energy conversion efficiency limits the application of the MPT in long distance inspection. In this article, a method for the enhancement of the MPT was proposed by dynamic magnetic field optimization using a soft magnetic patch (SMP). The SMP can reduce the magnetic resistance of the magnetic circuit, which increases the dynamic magnetic field intensity in the magnetostrictive patch during wave generation and restricts the induced dynamic magnetic field within the area around the coils for sensing during wave detection. Numerical simulations carried out at different frequencies verified the improvement of the dynamic magnetic fields by the SMP and influence of different affecting factors. The experimental validations of the signal enhancement in wave generation and detection were performed in an aluminum plate. The amplitude magnification could reach 12.7 dB when the MPTs were covered by the SMPs. Based on the numerical and experimental results, the SMP with a large relative permeability and thickness and close fitting between the SMP and coils were recommended when other application conditions were met.

12 March 2019 in Applied Sciences
Verified
Journal Article
Open access
PDF file
PZPengfei Zhang
Pengfei Zhang
ZTZhifeng Tang
Zhifeng Tang
FLFuzai Lv
Fuzai Lv
KYKeji Yang
Keji Yang
Ultrasonic guided waves (UGWs) have attracted attention in the nondestructive testing and structural health monitoring (SHM) of multi-wire cables. They offer such advantages as a single measurement, wide coverage of the acoustic field, and long-range propagation ability. However, the mechanical coupling of multi-wire structures complicates the propagation behaviors of guided waves and signal interpretation. In this paper, UGW propagation in these waveguides is investigated theoretically, numerically, and experimentally from the perspective of dispersion and wave structure, contact acoustic nonlinearity (CAN), and wave energy transfer. Although the performance of all possible propagating wave modes in a multi-wire cable at different frequencies could be obtained by dispersion analysis, it is ineffective to analyze the frequency behaviors of the wave signals of a certain mode, which could be analyzed using the CAN effect. The CAN phenomenon of two mechanically coupled wires in contact was observed, which was demonstrated by numerical guided wave simulation and experiments. Additionally, the measured guided wave energy of wires located in different layers of an aluminum conductor steel-reinforced cable accords with the theoretical prediction. The model of wave energy distribution in different layers of a cable also could be used to optimize the excitation power of transducers and determine the effective monitoring range of SHM.

1 August 2023 in IEEE Robotics and Automation Letters
Verified
Journal Article
Closed access
YWYunjiang Wang
Yunjiang Wang
TLTianjian Liu
Tianjian Liu
XHXinben Hu
Xinben Hu
KYKeji Yang
Keji Yang
YZYongjian Zhu
Yongjian Zhu
HJHaoran Jin
Haoran Jin
Robot-assisted ultrasound scanning acquires spatial-property labeled images under high consistency, holding the potential to reconstruct the volume with more intuitive images for examination and surgery guidance. Promisingly, the vertebral level identification, as a time-consuming procedure before spine surgery, can be achieved by robotic ultrasound systems. However, the quality of ultrasound images subjects to the conditions of the examination, including the probe placement, the ultrasound beam incidence angle and the applied contact force. Especially, the spine holds a long and narrow, multi-joint, chain-like structure which is not simply compliant to the probe, presenting challenges to acquire high quality images and keep safety. This letter presents a compliant joint based robotic ultrasound system (CJRUS) for imaging the human spine. A compliant joint based adjusting mechanism (CJAM) is attached to the robotic manipulator to adjust the contact force with patients. A floating scanning strategy is proposed for the manipulator to maintain a buffer zone from the human body and determine the pose of the probe indirectly from the collection of dorsal shape. Phantom experiments concluded that the system could provide inherent safety (the output force was constrained to 20 N by rotary buffer) and adaptive capacity (the settling time was < 1 s for targets with different stiffness and the maximum overshoot decreased 90% in prediction force control) to scanning objects. In human trials, the coronal slice of the reconstructed volume obtained by CJRUS showed comparative results as freehand scanning and equivalent image qualities evaluated by picture contrast and edge gradient. CJRUS is expected to play a significant role in radiation-free navigation of minimally invasive spinal surgery in the future.

16 November 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
BYBei Yu
Bei Yu
HJHaoran Jin
Haoran Jin
YMYujian Mei
Yujian Mei
JCJian Chen
Jian Chen
EWEryong Wu
Eryong Wu
KYKeji Yang
Keji Yang
Full-matrix capture (FMC)-based ultrasonic imaging provides good sensitivity to small defects in non-destructive testing and has gradually become a mainstream research topic. Many corresponding algorithms have been developed, e.g., the total focusing method (TFM). However, the efficiency of the TFM is limited, especially in multi-layered structures. Although the appearance of wavenumber algorithms, such as extended phase-shift migration (EPSM) methods, has improved imaging efficiency, these methods cannot be applied to cases with oblique incidence. Therefore, a modified wavenumber method for full-matrix imaging of multi-layered structures with oblique array incidence is proposed. This method performs a coordinate rotation in the frequency domain to adapt it to the oblique incidence. It then utilizes wave-field extrapolation to migrate the transmitting and receiving wave field to each imaging line, and a correlation imaging condition is used to reconstruct a total focused image. The proposed method can deal with any incident angle without precision loss. Moreover, it inherits the computational efficiency advantages of the wavenumber algorithms. The simulation and experimental results show that the proposed method performs better in terms of accuracy and efficiency than the TFM. Specifically, it is nearly 60 times faster than the TFM when processing an FMC dataset with a size of 4096 × 64 × 64.