Sergei A. Chizhik

Sergei A. Chizhik

Auto-generated profile, based on publicly available information

Sergei A. Chizhik

A. V. Luikov Heat and Mass Transfer Institute of the National Academy of Sciences of Belarus, Minsk, Republic of Belarus

Research Focus & Metrics

Academic Career Length

26Years (2001-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 October 2016 in Journal of Materials Engineering and Performance
Verified
Journal Article
Open access
PDF file
TKTatyana Kuznetsova
Tatyana Kuznetsova
Tatsiana ZubarTatsiana Zubar
Tatsiana Zubar
SCS. Chizhik
S. Chizhik
AGAdam Gilewicz
Adam Gilewicz
OLO. Lupicka
O. Lupicka
BWBogdan Warcholinski
Bogdan Warcholinski
MoCN coatings have been formed by cathodic arc evaporation using the mixture of acetylene and nitrogen and pure molybdenum target. The surface structure, in conjunction with x-ray data, was analyzed by atomic force microscopy (AFM). The AFM results show differently shaped grain forms on the surface of coatings investigated. The increase in carbon in chemical coatings composition results in the reduction in surface grain size and the increase in roughness of the coatings.

15 September 2021 in Nanomaterials
Verified
Journal Article
Open access
PDF file
GMGalina Melnikova
Galina Melnikova
TKTatyana Kuznetsova
Tatyana Kuznetsova
VLVasilina Lapitskaya
Vasilina Lapitskaya
APAgata Petrovskaya
Agata Petrovskaya
SCSergei Chizhik
Sergei Chizhik
SYStanislav Yakovin
Stanislav Yakovin
The present paper addresses the problem of identification of microstructural, nanomechanical, and tribological properties of thin films of tantalum (Ta) and its compounds deposited on stainless steel substrates by direct current magnetron sputtering. The compositions of the obtained nanostructured films were determined by energy dispersive spectroscopy. Surface morphology was investigated using atomic force microscopy (AFM). The coatings were found to be homogeneous and have low roughness values (<10 nm). The values of microhardness and elastic modulus were obtained by means of nanoindentation. Elastic modulus values for all the coatings remained unchanged with different atomic percentage of tantalum in the films. The values of microhardness of the tantalum films were increased after incorporation of the oxygen and nitrogen atoms into the crystal lattice of the coatings. The coefficient of friction, CoF, was determined by the AFM method in the “sliding” and “plowing” modes. Deposition of the coatings on the substrates led to a decrease of CoF for the coating-substrate system compared to the substrates; thus, the final product utilizing such a coating will presumably have a longer service life. The tantalum nitride films were characterized by the smallest values of CoF and specific volumetric wear.

1 March 2001 in Macromolecular Symposia
Verified
Journal Article
Closed access
PDF file
SCSergei A. Chizhik
Sergei A. Chizhik
VGValery V. Gorbunov
Valery V. Gorbunov
ILIgor Luzinov
Igor Luzinov
NFNobi Fuchigami
Nobi Fuchigami
VTVladimir V. Tsukruk
Vladimir V. Tsukruk

1 April 2011 in Biophysics
Verified
Journal Article
Closed access
PDF file
ESE. V. Shamova
E. V. Shamova
OBO. D. Bichan
O. D. Bichan
EDE. S. Drozd
E. S. Drozd
IGIrina Gorudko
Irina Gorudko
SCS. A. Chizhik
S. A. Chizhik
AVAnatoly F. Vanin
Anatoly F. Vanin
The effect of NO donors (sodium nitroprusside, S-nitrosoglutathione, dinitrosyl-iron complexes) on the functional and mechanical properties of human platelets and red blood cells has been...

1 January 2010 in Advances in Tribology
Verified
Journal Article
Open access
PDF file
SCSergei A. Chizhik
Sergei A. Chizhik
KWKrzysztof Wierzcholski
Krzysztof Wierzcholski
ATAnastasia V. Trushko
Anastasia V. Trushko
MZMariya A. Zhytkova
Mariya A. Zhytkova
AMAndrzej Miszczak
Andrzej Miszczak
Results of investigation of the elastic modulus for cartilage tissue using a technique of micro- and nanoindentation performed with help of an atomic force microscope are presented. SEM and AFM methods were applied to visualize a topography of surface layers of the entire cartilage and as well as its slices and thus to reveal features of the collagen fibers orientation. The technique used for a quantitative evaluation of the elastic modulus under compression against a ball microindenter (curvature radius - 350 micron) and a nanoindenter (30 nm) is described. It was shown that the cartilage behavior is highly stabile under the load if the entire composite structure of cartilage tissue is engaged into the deformation process. Tribological characteristics were investigated using the ball indenter oscillated by a tuning fork. Dependence of the friction coefficient from applied loads was obtained that revealed strong influence of an interstitial fluid on friction properties. Friction coefficient of a rat cartilage tissue as 0.08 was obtained using a developed plant prototype for tribological measurements based on the AFM construction.

26 December 2023 in Materials
Verified
Journal Article
Open access
PDF file
VLVasilina Lapitskaya
Vasilina Lapitskaya
ANAndrey Nikolaev
Andrey Nikolaev
Anastasiya KhabaravaAnastasiya Khabarava
Anastasiya Khabarava
ESEvgeniy Sadyrin
Evgeniy Sadyrin
PAPavel Evgenievich Antipov
Pavel Evgenievich Antipov
SCSergei Chizhik
Sergei Chizhik
Utilizing reactive DC magnetron sputtering method, TiN coatings were deposited on the silicon substrates at different nitrogen flows and powers. A study of the X-ray phase composition of the coatings was carried out. The stoichiometric composition of the coatings was determined using energy dispersive x-ray spectroscopy. The structure of the surface, cross-section, and thickness of the coatings were determined using scanning electron (SEM) and atomic force microscopy (AFM). A significant change in the surface structure of TiN coatings was established with changes in deposition power and nitrogen flow. SEM images of cross-sections of all coated samples showed that the formation of coatings occurs in the form of a columnar structure with a perpendicular orientation relative to the silicon substrate. The mechanical properties (elastic modulus E and microhardness H) of TiN coatings of the first group demonstrate a maximum at a nitrogen flow of 3 sccm and are 184 ± 11 GPa and 15.7 ± 1.3 GPa, respectively. In the second group, the values of E and H increase due to a decrease in the size of the structural elements of the coating (grains and crystallites). In the third group, E and H decrease. Microtribological tests were carried out in 4 stages: at a constant load, multi-cycle for 10 and 100 cycles, and with increasing load. The coefficient of friction (CoF) and specific volumetric wear ω depend on the roughness, topology, and mechanical properties of the resulting coatings. Fracture toughness was determined using nanoscratch and depends on the mechanical properties of TiN coatings. Within each group, coatings with the best mechanical and microtribological properties were described: in the first group—TiN coating at 3 sccm (with (29.6 ± 0.1) at.% N), in the second group—TiN coating at 2 sccm (with (40.8 ± 0.2) at.% N), and in the third group—TiN coating at 1 sccm (c (37.3 ± 0.2) at.% N).