Ricky Saputra

Ricky Saputra

Auto-generated profile, based on publicly available information

Ricky Saputra

School of Computer Science and Engineering, Taylor's University Lakeside Campus, No. 1 Jalan Taylor's, 47500, Subang Jaya, Selangor, Malaysia

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2021 in Chemosphere
Verified
Journal Article
Closed access
RSRicky Saputra
Ricky Saputra
RWRashmi Walvekar
Rashmi Walvekar
MKMohammad Khalid
Mohammad Khalid
NMNabisab Mujawar Mubarak
Nabisab Mujawar Mubarak
MSMika Sillanpää
Mika Sillanpää

1 July 2020 in Journal of Molecular Liquids
Verified
Journal Article
Closed access
RSRicky Saputra
Ricky Saputra
RWRashmi Walvekar
Rashmi Walvekar
MKMohammad Khalid
Mohammad Khalid
NMNabisab Mujawar Mubarak
Nabisab Mujawar Mubarak

1 June 2019 in Journal of Environmental Chemical Engineering
Verified
Journal Article
Closed access
RSRicky Saputra
Ricky Saputra
RWRashmi Walvekar
Rashmi Walvekar
MKMohammad Khalid
Mohammad Khalid
KSKaveh Shahbaz
Kaveh Shahbaz
SRSuganti Ramarad
Suganti Ramarad

1 May 2020 in Journal of Molecular Liquids
Verified
Journal Article
Closed access
RSRicky Saputra
Ricky Saputra
RWRashmi Walvekar
Rashmi Walvekar
MKMohammad Khalid
Mohammad Khalid
CRChantara Thevy Ratnam
Chantara Thevy Ratnam
NMNabisab Mujawar Mubarak
Nabisab Mujawar Mubarak
SDSwapnil Dharaskar
Swapnil Dharaskar

26 February 2018 in MATEC Web of Conferences
Verified
Journal Article
Open access
RWRashmi Walvekar
Rashmi Walvekar
KKKishen Kunju
Kishen Kunju
RSRicky Saputra
Ricky Saputra
KSKhalid Siddiqui
Khalid Siddiqui
SRSuganti Ramarad
Suganti Ramarad
Waste rubber is a polymeric material containing 50% of rubber and is generally referred to as waste tyre rubber. The main purpose of this research is to study ultrasonic devulcanisation of waste rubber utilising deep eutectic solvent (DES) of ZnCl2:Urea by improving process parameters such as sonication time, reaction temperature and rubber: DES mass ratio by effectively cleaving cross-link sulphur bonds. DES was created and prepared by mixing ZnCl2 with urea at 2:7 and 1:4 molar ratios respectively. Physicochemical properties of the prepared DES was measured using DSC, KFT and TGA analysis to find the freezing point, moisture content and degradation temperature, whereby their freezing point below 60°C, moisture content lower than 3.0 wt.% and 200°C degradation temperature average. Rubber to DES mass ratio was varied at 1:20, 1:30 and 1:40 and sonicated for 15 minutes inside ultrasonic water-bath. Samples were placed onto hot plate whereby heating temperature was varied at room temperature, 130°C, 150°C, and 180°C for 15 minutes. Samples were filtered, washed with distilled water and dried in oven for 24 hours. Once dried, samples were taken for analysis using TGA, EDX, FESEM, FTIR and Gel content. Under TGA analysis, most samples have an average degradation temperature of 200°C, hence justifying a successful devulcanisation. EDX analysis shows two occurrences during devulcanisation process which is bond reformation and cleavage. Furthermore, it is determined that heating temperature of 130°C is an important parameter as it is the optimum temperature for ZnCl2:Urea. Under FTIR analysis, it shows that disulphide bond, S-S is the only bond that is being broken while the rest still remains the same. Gel content analysis showed that samples have a lower soluble fraction after devulcanisation process. Finally, FESEM proves that at 130°C and 15 minutes is the optimum temperature and time which is illustrated by the smooth surface at that particular point.