23 August 2019 in Science
Joining the laser welding club: Laser welding is an integral part of modern manufacturing, but it fractures ceramic materials. Penilla et al. developed two methods for welding ceramics using ultrafast lasers. One method tunes the ceramic properties, allowing the laser to transit through the ceramic and weld at the interface between pieces. The other method optimizes a gap between pieces to efficiently deposit energy. Both methods leverage short but energetic pulses to create a melt pool that allows ceramics to be joined, without the high temperature used for traditional ceramic welds. Science , this issue p. 803
1 September 2013 in Acta Materialia
7 October 2016 in Physical Review B
We demonstrate robust interface strain-induced perpendicular magnetic anisotropy in atomically flat ferrimagnetic insulator (TIG) films grown with pulsed laser deposition on a substituted substrate which maximizes the tensile strain at the interface. In bilayers consisting of Pt and TIG, we observe large squared Hall hysteresis loops over a wide range of thicknesses of Pt at room temperature. When a thin Cu layer is inserted between Pt and TIG, the Hall hysteresis magnitude decays but stays finite as the thickness of Cu increases up to 5 nm. However, if the Cu layer is placed atop Pt instead, the Hall hysteresis magnitude is consistently larger than when the Cu layer with the same thickness is inserted in between for all Cu thicknesses. These results suggest that both the proximity-induced ferromagnetism and spin current contribute to the anomalous Hall effect.
1 December 2018 in APL Materials
We show tunable strain-induced perpendicular magnetic anisotropy (PMA) over a wide range of thicknesses in epitaxial ferrimagnetic insulator Eu3Fe5O12 (EuIG) and Tb3Fe5O12 (TbIG) thin films grown by pulsed-laser deposition on Gd3Ga5O12 with (001) and (111) orientations, respectively. The PMA field is determined by measuring the induced anomalous Hall loops in Pt deposited on the garnet films. Due to positive magnetostriction constants, compressive in-plane strain induces a PMA field as large as 32.9 kOe for 4 nm thick EuIG and 66.7 kOe for 5 nm thick TbIG at 300 K and relaxes extremely slowly as the garnet film thickness increases. In bilayers consisting of Pt and EuIG or Pt and TbIG, robust PMA is revealed by squared anomalous Hall hysteresis loops in Pt, the magnitude of which appears to be only related to the net magnetic moment of iron sublattices. Furthermore, the magnetostriction constant is found to be 2.7 × 10−5 for EuIG and 1.35 × 10−5 for TbIG, comparable with the values for bulk crystals. Our results demonstrate a general approach of tailoring magnetic anisotropy of rare earth iron garnets by utilizing modulated strain via epitaxial growth.
11 June 2014 in Journal of Physics: Condensed Matter
Acoustic emission has been measured and statistical characteristics analyzed during the stress-induced collapse of porous berlinite, AlPO4, containing up to 50 vol% porosity. Stress collapse occurs in a series of individual events (avalanches), and each avalanche leads to a jerk in sample compression with corresponding acoustic emission (AE) signals. The distribution of AE avalanche energies can be approximately described by a power law p(E)dE = E(-ε)dE (ε ~ 1.8) over a large stress interval. We observed several collapse mechanisms whereby less porous minerals show the superposition of independent jerks, which were not related to the major collapse at the failure stress. In highly porous berlinite (40% and 50%) an increase of energy emission occurred near the failure point. In contrast, the less porous samples did not show such an increase in energy emission. Instead, in the near vicinity of the main failure point they showed a reduction in the energy exponent to ~ 1.4, which is consistent with the value reported for compressed porous systems displaying critical behavior. This suggests that a critical avalanche regime with a lack of precursor events occurs. In this case, all preceding large events were 'false alarms' and unrelated to the main failure event. Our results identify a method to use pico-seismicity detection of foreshocks to warn of mine collapse before the main failure (the collapse) occurs, which can be applied to highly porous materials only.
2 July 2013 in Journal of Physics: Condensed Matter
We study acoustic emission avalanches during the process of failure of porous alumina samples (Al2O3) under compression. Specimens with different porosities ranging from 30% to 59% have been synthesized from a mixture of fine-grained alumina and graphite. The compressive strength as well as the characteristics of the acoustic activity have been determined. The statistical analysis of the recorded acoustic emission pulses reveals, for all porosities, a broad distribution of energies with a fat tail, compatible with the existence of an underlying critical point. In the region of 35%–55% porosity, the energy distributions of the acoustic emission signals are compatible with a power-law behaviour over two decades in energy with an exponent = 1.8 ± 0.1.