13 September 2023 in IEEE Transactions on Antennas and Propagation
In this communication, an optically transparent reflectarray antenna based on indium tin oxide (ITO) material is presented. The reflectarray is composed of a patterned ITO array, two quartz glass substrates, and an ITO ground. By introducing an air gap between the quartz glass substrates, a multilayer hybrid dielectric substrate is formed, reducing the high conductor loss of the ITO material. The heterogeneous single- and combined-resonance elements are jointly utilized to achieve a wider phase variation. At the center frequency of 20 GHz, the reflectarray element owns a reflection loss of less than 1.8 dB and a phase variation of 494°. For verification, a $15\times15$ -element optically transparent reflectarray with a focus-to-diameter (F/D) ratio of 0.9 is designed, simulated, and measured. The measured results demonstrate good radiation characteristics, showing a measured gain of 24.4 dBi, a 1.5-dB gain bandwidth of 20%, and an overall optical transmittance of 75%. Compared with previously reported ITO-based transparent reflectarrays, this design achieves a wide phase variation, high optical transparency, low return loss, and broad bandwidth simultaneously.
9 September 2016 in IEEE Transactions on Microwave Theory and Techniques
This paper demonstrates plate-laminated waveguide filters in diffusion bonding technology for the first time and shows their uses in the integration with a corporate-feed slot array antenna for E-band ultrahigh capacity point-to-point communications. First, a single-cavity resonator model is studied and the measured high unloaded quality of 2121 at 79.07 GHz indicates its potential in the design of low-loss filters. Consequently, a sixth-order T-shaped cavity bandpass filter that comprises of ten cavity resonators is developed. It exhibits insertion losses of 3.4 and 3.3 dB at 78.5 GHz at two output ports, a 3-dB fractional bandwidth of 20.5%, as well as a small in-band amplitude/phase difference. Then, a fourth-order bandstop filter based on a band-rejection element is presented. It provides a high rejection level of 55 dB at 78.5 GHz and insertion losses of 0.44 and 0.28 dB at 73.5 and 83.5 GHz. The architectures of the proposed filters show attractive compatibility properties for integration. Finally, the proposed filters are fully integrated into a corporate-feed circuit of a 16 × 16-element slot array antenna without an interconnection circuit. With the seamless integration, the proposed building blocks demonstrate well-preserved high efficiency (only a low loss is introduced by the filters) and unchanged radiation characteristic (low sidelobe level, low cross polarization, and high directivity) in the designed passband, as well as specified bandstop performance.
19 August 2020 in IEEE Transactions on Antennas and Propagation
This paper reports for the first time the design of a 60-GHz planar antenna system for radiative near-field region line-of-sight (LOS) link, based on an orbital angular momentum (OAM) multiplexing. The antenna system is composed of a radial line slot array (RLSA) fed by a Butler network, made in post-wall waveguide technology, and located underneath the array. The network can launch different progressive phase states in the RLSA parallel plate waveguide (PPW) to radiate three different OAM beams. To focalize each beam in the radiative near-region the use of a modified Laguerre-Gaussian aperture distribution is proposed to extend the range where the link is guaranteed. The design concept has been verified by prototyping and testing a 20 free-space wavelengths radius antenna. The measurements show that the proposed antenna can generate simultaneously the three OAM-mode states n = 0, –1, and +1.
5 June 2023 in IEEE Transactions on Antennas and Propagation
This paper reports the design of a novel wideband and dual-polarized millimeter-wave antenna with single-layered geometry and low profile. The antenna is mainly composed of a square patch and two inverted-F antennas (IFAs), and they are located in the same substrate layer. Wide bandwidth has been achieved by taking advantage of the dual resonances generated by patch and IFA modes. The antenna feed is constructed by a through pin connecting to the corresponding IFA and, therefore, leading to a dual-polarized antenna performance as well as a single-layered antenna structure with a low profile of 0.07 λ 0 . An L-shaped metal strip has been introduced in order to improve the port isolation. The design concept has been verified by prototyping and testing a 2×2 array antenna in the Ka band. It has been demonstrated that the proposed 2×2 array antenna has a 21% bandwidth with average total efficiency higher than 72% and realized gain up to 11.1 dBi.
1 January 2017 in IEICE Transactions on Communications
This paper presents the design and characterization of an E-band 16×16-slot monopulse array antenna with full-corporate-feed fabricated by the commercially available batch process of diffusion bonding of laminated copper plates. The antenna is multi-layered, and consists of vertically-interconnected radiating elements, a corporate-feed circuit and a comparator. It has four input ports for different excitations. Sum and difference beams in different cut-planes for monopulse operation can be generated. The antenna has a quasi-planar profile, and a total size of 13.31 λ0×13.31λ0×1.52λ0 (λ0 is the wavelength at the design frequency of 78.5GHz). The antenna demonstrates a wide operation bandwidth of 17.2 (70-87.2) GHz for VSWR < 2. At 78.5GHz: 1) for the sum beam, there is a 32.6-dBi realized gain (83% antenna efficiency) and a 33.3-dBi directivity (95% aperture efficiency); 2) for the difference beams in the E-, H-, 45°-, and 135°-planes, the null depths are -53.0, -58.0, -57.8, and -65.6dB, respectively. Across the full operation band where the sum main-beam and difference null are able to consistently point at the boresight, the antenna also demonstrates excellent performance in terms of high gain, high efficiency, high isolation, low cross-polarization, and distinguished monopulse capability.
24 January 2025 in IEEE Microwave and Wireless Technology Letters
This letter proposes a new filtering power divider with out-of-phase characteristic and unequal power division ratio. Stemming from the traditional branch-line prototype, a modified structure is proposed to realize bandpass response with unequal power division and out-of-phase behavior. It is constructed in a three-stage branch-line structure, loaded with short-ended stubs, responsible for out-of-band suppressions. In addition, two anti-phase signals at output ports could be well isolated by a grounded chip resistor. For validation, a practical power divider circuit operating at 2.0 GHz with a 3-dB fractional bandwidth of 27% and a power division ratio of 4:1 are designed, fabricated, and measured. Results show that the presented power divider exhibits good filtering response, satisfactory out-of-band rejection, anti-phase difference, and desired unequal power distribution.