Majid Taghavi

Majid Taghavi

Auto-generated profile, based on publicly available information

Majid Taghavi

Shahid Beheshti Univ. (Iran, Islamic Republic of)

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 June 2022 in IEEE Sensors Journal
Verified
Journal Article
Closed access
MRMojtaba Rahimi
Mojtaba Rahimi
MMMohammad Malekmohammad
Mohammad Malekmohammad
MTMajid Taghavi
Majid Taghavi
MNMohammad Noori
Mohammad Noori
GPGholam-Mohammad Mohammad Parsanasab
Gholam-Mohammad Mohammad Parsanasab
In this paper, a differential micro-opto-electro-mechanical system (MOEMS) accelerometer based on the Fabry-Pérot (FP) micro-cavities is presented. The optical system of the device consists of two FP cavities and the mechanical system is composed of a proof mass that is suspended by four springs. The applied acceleration tends to move the PM from its resting position. This mechanical displacement can be measured by the FP interferometer formed between the proof mass cross-section and the optical fiber end-face. The proposed sensor is fabricated on a silicon-on-insulator wafer using the bulk micromachining method. The results of the sensor characterization show that the accelerometer has a linear response in the range of $\boldsymbol {\pm }1\text{g}$ . Also, the optical sensitivity and resolution of the sensor in the static characterization are 6.52 nm/g and $153 \boldsymbol {\mu }\text{g}$ . The sensor sensitivity in the power measurement is 49.6 mV/g and its resonant frequency is at 1372 Hz. Using the differential measurement method increases the sensitivity of the accelerometer. Based on the experimental data, the optical sensitivity in static mode is two times as high as that of a similar MOEMS accelerometer with one FP cavity.

9 April 2021 in IEEE Sensors Journal
Verified
Journal Article
Closed access
MTMajid Taghavi
Majid Taghavi
HLHamid Latifi
Hamid Latifi
GPGholam Mohammad Parsanasab
Gholam Mohammad Parsanasab
AAAbolfazl Abedi
Abolfazl Abedi
HNHamed Nikbakht
Hamed Nikbakht
MPMohammad Hosein Poorghadiri
Mohammad Hosein Poorghadiri
This paper is a report on the design and fabrication of a dual-axis micro-opto-electro-mechanical system (MOEMS) accelerometer. The device consists of a proof mass (PM) suspended by four L-shaped springs. Two Fabry-Pérot (FP) cavities are formed between the cross-sections of the PM and the ends of two cleaved optical fibers in perpendicular directions (the X and Y axes). The acceleration causes the proof mass to move in the reverse direction relative to the applied acceleration. The sensor is fabricated by a silicon-on-insulator wafer. The fabricated sensor is characterized both by spectral monitoring and power measurements in the range of ±1 g. The results of spectral measurements show 3.23 nm/g (g=9.81 m/s2: gravity constant) and 3.19 nm/g to the applied acceleration along the X and Y axes, respectively. Moreover, the obtained resolutions for the two directions of X and Y are 309 μg and 313 μg, respectively. Besides, the sensitivity of the sensor in power measurements is 550 mV/g and 528 mV/g in the X and Y directions, respectively. The sensor also possesses the resonant frequencies of 1382.5 Hz and 1398.6 Hz in the X and Y axes, respectively, in the range of ±1 g. The maximum cross-axis sensitivities obtained for this sensor are below 0.19% for each pair of X, Y, and Z axes. This value is fewer than the cross-axis sensitivity of most micro electro-mechanical systems without any post processing. This small value is a result of insensitivity of the FP spectrum to the lateral displacements of the PM.

23 January 2019 in Journal of Lightwave Technology
Verified
Journal Article
Closed access
MTMajid Taghavi
Majid Taghavi
HLHamid Latifi
Hamid Latifi
GPGholam Mohammad Parsanasab
Gholam Mohammad Parsanasab
AAAbolfazl Abedi
Abolfazl Abedi
HNHamed Nikbakht
Hamed Nikbakht
MSMohammad Javad Sharifi
Mohammad Javad Sharifi
This paper presents the design, fabrication, and characterization of a SU-8 four L-shaped beams optical MEMS (MOEMS) accelerometer based on a Fabry-Perot(FP) interferometer. An applied acceleration causes a displacement of the proof mass and changes the cavity of FP resonator. Fabrication process has been simplified such that only two photolithography steps are required and SU-8 is used for both the structural body and the sacrificial layer. To prevent the sacrificial layer from being exposed to UV light, a thin copper layer is coated by physical vapor deposition technique between the two SU-8 layers. The sensor chip consists of a proof mass which is suspended by four L-shaped springs. The movement of the proof mass in response to acceleration is detected by a FP cavity formed between the proof mass and the cleaved end of a single mode optical fiber. The fabricated sensor has a sensitivity of 12.5 μW/g and resonant frequency of 1872 Hz in the range of ±1g.

23 May 2022 in Optics Express
Verified
Journal Article
Closed access
MTMajid Taghavi
Majid Taghavi
AAAbolfazl Abedi
Abolfazl Abedi
GPGholam-Mohammad Parsanasab
Gholam-Mohammad Parsanasab
MRMojtaba Rahimi
Mojtaba Rahimi
MNMohammad Noori
Mohammad Noori
HLHamid Latifi
Hamid Latifi
In this paper, a closed-loop micro-opto-electro-mechanical system (MOEMS) accelerometer based on the Fabry-Pérot (FP) interferometer is presented. The FP cavity is formed between the end of a cleaved single-mode optical fiber and the cross-section of a proof mass (PM) which is suspended by four U-shaped springs. The applied acceleration tends to move the PM in the opposite direction. The arrays of fixed and movable comb fingers produce an electrostatic force which keeps the PM in its resting position. The voltage that can provide this electrostatic force is considered as the output of the sensor. Using a closed-loop detection method it is possible to increase the measurement range without losing the resolution. The proposed sensor is fabricated on a silicon-on-insulator wafer using the bulk micromachining method. The results of the sensor characterization show that the accelerometer has a linear response in the range of ±5 g. In the closed-loop mode, the sensitivity and bias instability of the sensor are 1.16 V/g and 40 µg, respectively.

10 May 2013 in Applied Optics
Verified
Journal Article
Closed access
PDF file
MCM. Sadegh Cheri
M. Sadegh Cheri
HLHamid Latifi
Hamid Latifi
FAF. Beygi Azar Aghbolagh
F. Beygi Azar Aghbolagh
ONO. R. Ranjbar Naeini
O. R. Ranjbar Naeini
MTMajid Taghavi
Majid Taghavi
MGMohammadAmir Ghaderi
MohammadAmir Ghaderi
In this paper, we present the fabrication and packaging of a cantilever-based airflow sensor integrated with optical fiber. The sensor consists of a micro Fabry–Perot (FP) cavity including a fiber and a micro cantilever that is fabricated using the photolithography method. Airflow causes a small deflection of the micro cantilever and changes the cavity length of the FP, which makes the fringe shift. The pressure distribution and velocity streamlines across the cantilever resulted from the airflow in the channel have been simulated by the finite element method. The experimental results demonstrate that the sensor has a linear sensitivity of 190 [fringe shift (pm)] per (l/min) and a minimum detectable airflow change of 0.05  (l/min).

27 November 2024 in PRX Quantum
Verified
Journal Article
Open access
SAShirin Afzal
Shirin Afzal
TZTyler J. Zimmerling
Tyler J. Zimmerling
MRMahdi Rizvandi
Mahdi Rizvandi
MTMajid Taghavi
Majid Taghavi
LELeili Esmaeilifar
Leili Esmaeilifar
SBShabir Barzanjeh
Shabir Barzanjeh
Entanglement is a valuable resource in quantum information technologies. The practical implementation of entangled photon sources faces obstacles from imperfections and defects inherent in physical systems, resulting in a loss or degradation of entanglement. The topological photonic insulators, however, have emerged as promising candidates, demonstrating an exceptional capability to resist defect-induced scattering, thus enabling the development of robust entangled sources. Despite their inherent advantages, building programmable topologically protected entangled sources remains challenging due to complex device designs and weak material nonlinearity. Here, we present a development in entangled photon-pair generation achieved through a nonmagnetic and tunable anomalous Floquet insulator, utilizing an optical spontaneous four-wave-mixing process. We verify the nonclassicality and time-energy entanglement of the photons generated by our topological system. Our experiment demonstrates a substantial enhancement in nonclassical photon-pair generation compared to devices reliant only on topological edge states. Our results could lead to the development of resilient quantum sources with potential applications in quantum technology. Published by the American Physical Society 2024