Purpose. Study of the influence of graphitized dust on abrasive wear of polytetrafluoroethylene-based composites. Research methods. Experimental studies were performed using modern methods of physical and mechanical tests, which ensures the reliability of the results. A laboratory mixer with a rotating electromagnetic field and a hydraulic table press TU 10003 TORIN were used for the production of samples. Weighing of samples for experiments was carried out on a VLR-200 scale, abrasion assessment was carried out on a HECKERT machine. The friction surfaces were studied using a BIOLAM-M microscope. Results. The conducted studies showed that the index of abrasive wear of the composite with a polytetrafluoroethylene matrix decreases from 2.974 mm3/m to 2.539 mm3/m with a content of 10 % of graphitized dust. This helps to increase the service life of parts, which will reduce the frequency of their replacement, as well as reduce production costs. Given that graphitized dust is a waste of metallurgical production, its secondary use as a filler for composite materials allows to partially solve the environmental problem of disposal of production waste. Scientific novelty. Today, the production of products from composite materials is one of the promising directions of production, because the combination of a polymer matrix with various fillers makes it possible to obtain more economically profitable materials, forming the necessary physical properties. The possibility of using production waste as a filler allows solving the current problem of recycling and disposal of environmentally harmful substances. Therefore, the conducted research opens up new ways to solve a complex of environmental and economic problems. Practical value. The obtained results are important in the further process of manufacturing composite materials. The ability to increase the resistance of the material to abrasive abrasion allows the production of parts that work in friction conditions.
The article investigates the influence of industrial B95 aluminium alloy and the high-entropy alloy FeNiCoB0,7Si0,3BeNb on the abrasive wear rate of ultra-high-molecular-weight polyethylene. It is shown that the introduction of both metal fillers increases the wear resistance of ultra-high-molecular-weight polyethylene to the fixed abrasive particles by approximately 50%. This improvement is attributed to the strengthening of the surface layer of the polymer matrix resulting from the incorporation of solid filler particles. This effect is confirmed by an increase in the hardness of the material on the Rockwell scale (HRR) by approximately 35% and a reduction in surface roughness by 40%. It is found that the high-entropy alloy has a more pronounced effect on reducing the abrasive wear rate of the polymer matrix. In both cases, the optimal complex of an optimal combination of functional properties is observed for composite materials containing 25 wt.% of B95 and FeNiCoB0,7Si0,3BeNb alloys. A further increase in the filler concentration in the polyethylene volume results in a reduction in abrasive wear resistance and hardness. This behaviour is explained by an increased number of structural defects in the polymer matrix, which degrade its mechanical integrity and reduce its ability to withstand external loads effectively.
The article presents the results of scientific research on the processes of operation of graphite plastic in a tribological unit. The effect of sliding speed and load on the intensity of wear and coefficient of friction of graphite plastic was determined, and mathematical models describing the tribotechnical behavior of graphite plastic depending on the load and sliding speed of the friction unit were developed. The research carried out in the paper made it possible to reveal the influence of the technological parameters of the operation process on the intensity of linear wear and the coefficient of friction of graphite plastic. The obtained mathematical dependencies make it possible to reliably predict the duration of the developed graphite plastic in tribological units of modern technology, which is important for ensuring the efficiency and reliability of machines and mechanisms.
These theses consider the perspective of introducing "4K" technology into the educational process. The development of such skills and abilities as creativity, critical thinking, sociability, and the ability to work in a team among students is very importa
10 December 2025 in Collection of scholarly papers of Dniprovsk State Technical University (Technical Sciences)
The article considers the effect of the percentage content of the liquid-quenched dispersed (50—100 μm) binary alloy of the Al-Mn system on the tribological properties of ultra-high-molecular-weight polyethylene under different operating conditions, such as the action of rigidly fixed abrasive particles and friction conditions without lubrication according to the “disk-pad” scheme. We discovered that introducing dispersed particles of a hard (HV ≈ 600 MPa) Al-11.6 % Mn alloy reduces the linear wear rate by 8.7 times and the abrasive wear index by 1.8 times compared to the pure polymer. The effect of microreinforcement explains the increase in wear resistance. It provides a uniform distribution of the applied load in the friction zone and decreases local stresses. Morphological analysis of the friction surfaces confirmed the formation of a more homogeneous surface layer structure. It is shown that increasing the alloy content to 25—30 wt. % leads to particle agglomeration, the formation of local stress concentrators, and deterioration of the tribological properties of polymer composites.