Marco Antonio Rodriguez-Frias

Marco Antonio Rodriguez-Frias

Auto-generated profile, based on publicly available information

Marco Antonio Rodriguez-Frias

School of Electrical and Electronic Engineering, The University of Manchester, Manchester M13 9PL, UK

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 November 2019 in IEEE Sensors Journal
Verified
Journal Article
Closed access
MRMarco Antonio Rodriguez-Frias
Marco Antonio Rodriguez-Frias
WYWuqiang Yang
Wuqiang Yang
Electrical capacitance tomography (ECT) and electrical resistance tomography (ERT) have been successfully developed to visualise dielectric and conductive distributions respectively. However, monitoring complex multiphase flows involve imaging highly dynamic distributions, which are constantly changing between dielectric-dominant and conducive-dominant. In this work, a dual-modality ERT/ECT system is developed for imaging dielectric-dominant and conducive-dominant distributions simultaneously. With a 4-terminal measurement configuration, the system can reduce the effect of parasitic impedances, acquiring simultaneously capacitance and conductance using a single set of electrodes and a single data acquisition system.

16 November 2018 in Measurement Science and Technology
Verified
Journal Article
Closed access
PDF file
RWRuican Wang
Ruican Wang
MFMarco A Rodriguez Frias
Marco A Rodriguez Frias
HWHaigang Wang
Haigang Wang
WYWuqiang Yang
Wuqiang Yang
JYJianmin Ye
Jianmin Ye
Normally, a gas–solids flow should be non-conductive. With the increase in moisture content in a gas–solids flow, the non-conductive flow may become low-conductive. For the measurement of low-conductive materials, i.e. particles with high moisture content, in the pharmaceutical industry, both electrical capacitance tomography (ECT) and traditional electrical resistance tomography driven by current (ERTc) generate poor images. An ERT driven by voltage (ERTv) may be suitable for the measurement of materials with low-conductivity. In this research, ERTv is used for the measurement of a wet gas–solids flow with different moisture content and different flow patterns, as well as a gas–liquid flow with different flow patterns. In the meantime, ECT is also used for the same flow conditions for comparison. The measurement results of ERTv and ECT are evaluated by the correlation coefficient. The results show that ERTv is good for measurement of a gas–solids flow with high moisture content and a gas–liquid flow when the conductivity of the continuous phase is low or moderate, while ECT is suitable for the measurement of a dry gas–solids flow.

21 September 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
MVManuel Vázquez-Nambo
Manuel Vázquez-Nambo
JGJose Antonio Gutierrez Gnecchi
Jose Antonio Gutierrez Gnecchi
EAEnrique Reyes Archundia
Enrique Reyes Archundia
WYWuqiang Yang
Wuqiang Yang
MRMarco-A. Rodriguez-Frias
Marco-A. Rodriguez-Frias
Daniel LoriasDaniel Lorias
Daniel Lorias
The physicochemical characterization of pharmaceutical materials is essential for drug discovery, development and evaluation, and for understanding and predicting their interaction with physiological systems. Amongst many measurement techniques for spectroscopic characterization of pharmaceutical materials, Electrical Impedance Spectroscopy (EIS) is powerful as it can be used to model the electrical properties of pure substances and compounds in correlation with specific chemical composition. In particular, the accurate measurement of specific properties of drugs is important for evaluating physiological interaction. The electrochemical modelling of compounds is usually carried out using spectral impedance data over a wide frequency range, to fit a predetermined model of an equivalent electrochemical cell. This paper presents experimental results by EIS analysis of four drug formulations (trimethoprim/sulfamethoxazole C14H18N4O3-C10H11N3O3, ambroxol C13H18Br2N2O.HCl, metamizole sodium C13H16N3NaO4S, and ranitidine C13H22N4O3S.HCl). A wide frequency range from 20 Hz to 30 MHz is used to evaluate system identification techniques using EIS data and to obtain process models. The results suggest that arrays of linear R-C models derived using system identification techniques in the frequency domain can be used to identify different compounds.

1 May 2016
Verified
Conference Paper
Closed access
MFMarco A. Rodriguez Frias
Marco A. Rodriguez Frias
WYWuqiang Yang
Wuqiang Yang
Electrical Resistance Tomography (ERT) has been widely accepted as a useful tool to visualize conductivity distributions. Traditional ERT systems use a scheme with current injection and voltage measurement to detect changes in conductivity in a region of interest. Such current injection is usually accomplished by the use of small metallic pin electrodes. As a consequence of the `soft-field' feature of the electric field and the use of small pin electrodes, there exists an axial dispersion of the sensing field i.e. fringe effect. In consequence, the reconstructed images are distorted and hence they can only provide qualitative information of the conductivity distribution. An ERT system with voltage excitation and larger electrodes would reduce the distortion due to the fringe effect. In addition, the use of a voltage source instead of current reduces the complexity and cost of the implementation while increases the range of conductivities the ERT system is capable to image. In this work, the construction of an ERT system with voltage excitation is described. In addition, the impact of driven guards in an ERT sensor is studied.

1 October 2017
Verified
Conference Paper
Closed access
MFMarco A. Rodriguez Frias
Marco A. Rodriguez Frias
WYWuqiang Yang
Wuqiang Yang
Electrical resistance tomography with voltage excitation (ERTv) has been proposed as an alternative approach, aiming to overcome the inherent limitations of conventional ERT with current injection. The use of a voltage source instead of a current source simplifies hardware while increasing the range of conductivity, which can be measured. In addition, this excitation scheme allows acquiring more independent measurements with the same number of electrodes than the conventional scheme. However, there is a major drawback of ERTv system, which is that the resistance of the switching stage and contact impedance have an effect on the measurements and cannot be neglected because they cause measurement errors and reduce the reliability of ERTv systems. In this paper, the impact of the contact impedance and the resistance of the switching stage are assessed. A 4-wire sensing scheme for ERTv is proposed to overcome the limitations.

1 October 2018
Verified
Conference Paper
Closed access
JLJun Long
Jun Long
MFMarco A. Rodriguez Frias
Marco A. Rodriguez Frias
KMKhursiah Zainal Mokhtar
Khursiah Zainal Mokhtar
WYWuqiang Yang
Wuqiang Yang
An integrated electrical capacitance tomography (ECT) and electrostatic sensor has been developed for measurement of volume flow rate in particulate processes. Unlike the traditional methods for mass/volume flow rate measurement, this integrated sensor can measure particle concentration and velocity at the same cross section instead of different cross sections. Experiment was carried out to measure particle concentration, velocity and volume flow rate using the developed sensor. Experimental results show that the integrated sensor can measure the parameters in particulate processes. The relative error of the measured volume flow rate is less than 10%.