26 February 2021 in IEEE Transactions on Biomedical Circuits and Systems
In this work, ISFET frontends utilising the direct tunneling current to eliminate trapped charge are proposed. The principle has been investigated and verified via silicon-imitated ISFET first, where silicon capacitors are used to imitate the passivation ones. Because the dominant tunneling components depend on the potential difference between Gate and Drain terminals, a source-follower structure could itself perform a highpass filter with time constant at 10–100 seconds level. Additionally, a time-constant regulation mechanism is presented by feeding the output signal back to the drain terminal of ISFETs, achieving a regulation factor over 50, namely from 4.7 seconds to 243.4 seconds in our implementation. Afterwards in chemical test, proposed ISFETs have been verified in terms of unit passivation capacitance, linearity, noise and sensitivity for ISFETs with 3 different top metal areas. It is found that approximately 30.12 mV/pH sensitivity can be achieved, and for the first time we managed to derive the relation between chemical flicker noise and sensing metal area.
25 July 2025 in IEEE Sensors Journal
This work proposes a fabrication and optimization process of miniaturized Ag/AgCl reference electrodes (REs) at a micrometer ( $\mu \text {m}$ ) scale for the miniaturized chemical sensors and it provides a stable reference voltage for ion-sensitive field effect transistor (ISFET) to detect pH in biochemical environments. The thin silver films are grown by magnetron sputtering and chemically chlorinated to form the Ag/AgCl microelectrodes. Different chlorination durations and current densities have been applied to investigate the best fabrication recipe. The electrical performance of the proposed microelectrode has been compared with a standard saturated calomel electrode (SCE), and it is observed that the electrode fabricated with an optimized recipe could provide less than 4-mV accuracy within the pH range from 4 to 10 and lifetime exceeding 200 min even with only ${1}.{95}\times {10}^{{5}}\mu \text {m}^{{2}}$ area. The correlation between the microelectrode area and both impedance and noise is expressed by equations, serving as a theoretical guide for designing and fabricating the Ag/AgCl RE on the chip.
11 February 2025 in IEEE Transactions on Biomedical Circuits and Systems
In [1], in section III.E of the article, we calculate the equivalent tunnelling current according to equation (4) by using the value of Cg, eff as 1.679 fF, which is about 4.6 times smaller than the correct value. This leads to the wrong equivalent impedance value obtained in the final Fig. 10 is about 4.6 times larger than the correct value, and the equivalent impedance should be about 2.2 PΩ at this size, so according to the basis of the above, the article should be corrected as follows:
29 December 2025 in IEEE Transactions on Biomedical Circuits and Systems
This paper introduces a capacitively coupled analog front-end featuring an adjustable high-pass cutoff frequency range of 7 mHz to 6.29 Hz. The DC operating point for the input differential pair is set by the dynamic equilibrium of the direct tunneling (DT) current. An output DC-servo loop (O-DSL), utilizing a duty-cycled operational transconductance amplifier (DC-OTA) together with a digital-assistant transconductance amplifier (DA-OTA), is designed at the main amplifier’s output nodes. By employing DC-OTA techniques in the O-DSL, an equivalent transconductance as low as 0.18 pA/V has been achieved, enabling the front-end to reach a 7 mHz high-pass cutoff frequency with a 6 pF on-chip integrating capacitor. A DA-OTA technique is used to widen the compensation range for low frequency interference. Additionally, a positive feedback capacitor in conjunction with a dual loop control mechanism is applied to enhance input impedance to 5.2 G$\Omega$ at 50 Hz within 30 ms calibration time. The front-end is fabricated in a standard 180 nm CMOS process, with a total current consumption of 3.01 $\mu$A and 6.37 NEF.