8 August 2022 in IEEE Transactions on Microwave Theory and Techniques
To improve the power handling capability at ground stations of a 5.8-GHz solar space power satellite using microwave power transmission, a power charge-pump meta-semiconductor field-effect transistor (MESFET)-based rectifier is presented in this article. Unlike conventional microwave Schottky diodes, diode-connected MESFETs, whose nonlinear characteristics help them to have a unique current–voltage (I-V) curve that overcomes the limitations of a Schottky diode. Thus, the maximum input power of the proposed rectifier is extended up to 251.2 mW by replacing a Schottky diode with a diode-connected MESFET. Additionally, a class F harmonic processing network is introduced to control the voltage and current waveform at the load of the rectifier. Consequently, the RF-dc conversion efficiency is increased since the power dissipation is limited at the junction resistance of both the drain and the source of the MESFET. Owing to the abnormal characteristics of the diode-connected MESFET, the measured conversion efficiency of our rectifier is approximately 73.2% at 126 mW, and the input power range for rectifier efficiency higher than 50% is between 16 and 224 mW. The proposed rectifier for the space solar power satellite application is demonstrated and verified using a microwave wireless power transmission system.
30 June 2023 in IEEE Transactions on Circuits and Systems II: Express Briefs
This brief reports a compact DC-110GHz single-pole single-throw (SPST) switch in 22nm FDSOI CMOS technology. The switch adopts solely three n-MOSFETs, two of them with a special device option to reduce the substrate parasitic effects, and a third n-MOSFET in parallel to the gate resistance of the series n-MOSFET to improve isolation. Unlike prior wideband mmwave switches, it does not make use of any large passive components, such as spiral inductors, transformers and transmission lines, which are prone to large parasitic effects, including losses, and require large area on silicon. Altogether, the novel switch circuit allows a very compact design, low losses and high isolation performance. The switch exhibits an insertion loss lower than 3.1 dB, an isolation better than 22 dB, and a return loss better than 12 dB, over the entire frequency range from DC to 110 GHz. The area on die amounts to 160 lm2, that is up two or more orders of magnitude smaller than prior wideband mm-wave SPST switches.
7 September 2017 in IEEE Transactions on Microwave Theory and Techniques
Herein, we present a floating 2-port nonreciprocal negative capacitance (NCAP) circuit that employs a unilateral gain boosting technique by including an asymmetric cross-coupled differential cascode transistor pair. The proposed circuit provides an asymmetric gain characteristic. The forward gain ( $S_{21}$ ) is increased at the cost of the backward gain ( $S_{12}$ ). The technique not only provides a boosted forward gain but also stable operation resulting from this reduced backward gain. We further investigate the stability of the NCAP circuit in terms of the output resistances of the current sources in the circuit. The proposed NCAP circuit was implemented in IBM 7RF 180-nm CMOS technology and was designed to have a supply voltage of 3 V and a current of 10 mA. The S-parameter measurements showed a self-resonance frequency of 2.25 GHz. The maximum $S_{21}$ was −0.2 dB at 1 GHz. In the frequency range from 0.5 to 1.5 GHz, the capacitance was approximately −4 pF, and the difference between $S_{21}$ and $S_{12}$ was 8.7–9.6 dB. The size of the core chip was $150 \times 190~\mu \text{m}^{2}$ .
6 November 2018 in IEEE Transactions on Microwave Theory and Techniques
21 January 2019 in Microwave and Optical Technology Letters
1 November 2018 in Electronics Letters
A vertically symmetric lumped element directional coupler (VSLEDC) providing broadband characteristics is proposed. In simulations, the proposed VSLEDC showed a 43.8% broader bandwidth than a horizontally and vertically symmetric lumped element directional coupler under similar design conditions for the same insertion loss. The proposed coupler was implemented in a Global Foundry 130 nm CMOS technology. The overall chip size was 1300 µm × 850 µm. The coupling was designed to be −10 dB at 1 GHz. The S ‐parameter measurements showed an absolute bandwidth and a fractional bandwidth of 141.1 MHz and 14.11%, respectively. Within the bandwidth, the insertion loss was 1.6‒1.8 dB.