Randi Purnama Putra

Randi Purnama Putra

Auto-generated profile, based on publicly available information

Randi Purnama Putra

Universitas Negeri Padang

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 February 2022 in Automotive Experiences
Verified
Journal Article
Open access
PDF file
RPRandi Purnama Putra
Randi Purnama Putra
DYDori Yuvenda
Dori Yuvenda
Muji SetiyoMuji Setiyo
Muji Setiyo
AAAndrizal Andrizal
Andrizal Andrizal
MMMartias Martias
Martias Martias
A city car is needed to overcome congestion and parking spaces in urban areas. However, currently, the body design of the city car is still experiencing problems, namely the value of the large drag coefficient, which causes an increase in fuel consumption. This study aims to design a city car body with two passengers that is more aerodynamic so as to minimize fuel use. This research method is a numerical simulation model using the ANSYS fluent students version 2021. Parameters in the form of drag coefficient values, velocity streamlines and velocity contours on the city car are aerodynamic aspects that are analyzed. The results show that the dimensions of the designed city car have a length of 2.59 m, a width of 1.6 m, and a height of 1.52 m by considering the ergonomic parameters and comfort of the user so that it fits the character of the people in Indonesia. In addition, from the independence grid analysis performed, the value of the number of meshes that have the smallest error value is obtained, namely mesh C (the number of meshes is 129,635). Mesh C has an error of 7.2%. It was found that as the velocity increases, the value of the drag coefficient (CD) produced is relatively smaller. In a city car with a velocity of 10 m/s, the drag coefficient value is 0.599, at a velocity of 20 m/s, the drag coefficient value is 0.594, and a velocity of 30 m/s is a drag coefficient value of 0.591.

23 April 2022 in Automotive Experiences
Verified
Journal Article
Open access
PDF file
DYDori Yuvenda
Dori Yuvenda
BSBambang Sudarmanta
Bambang Sudarmanta
JJJamaludin Jamaludin
Jamaludin Jamaludin
OMOki Muraza
Oki Muraza
RPRandi Purnama Putra
Randi Purnama Putra
SPSri Rizki Putri Primandari
Sri Rizki Putri Primandari
Compressed natural gas (CNG) is a popular alternative fuel because of its more environmentally friendly properties than fossil fuels , including applications in diesel engines. However, supplying too much compressed natural gas fuel causes poor engine performance and emissions due to a decrease in the air-fuel ratio on the dual-fuel engine. The addition of air using electric superchargers was done to return the air-fuel ratio to ideal conditions. Lambda value (λ) was variation under low load (1.52 to 2.71), medium load (1.18 to 2.17), and high load (0.94 to 2.17) on a CNG-diesel dual fuel engine. The addition of pure air in each load can increase combustion stability in certain lambda, which was indicated by an increase in thermal efficiency, heat release rate, and a decrease in ignition delay, combustion duration, hydrocarbon, and carbon monoxide emissions.

4 August 2024 in Automotive Experiences
Verified
Journal Article
Open access
PDF file
RPRandi Purnama Putra
Randi Purnama Putra
DYDori Yuvenda
Dori Yuvenda
WAWanda Afnison
Wanda Afnison
RLRemon Lapisa
Remon Lapisa
MMMilana Milana
Milana Milana
DHDani Harmanto
Dani Harmanto
The chassis is an important part of a car which must have a strong construction to withstand the weight of the vehicle. The purpose of this research is to create a city car's chassis that can hold two passengers and then crash-test the finished product. In this research, a development method was used using SolidWorks software and the student version of ANSYS R2 2023 as software for creating chassis designs and crash test simulations. The study's findings indicate that the car frame's measurements are 2.46 meters in length, 1.33 meters in height, and 1.39 meters in width. The steel of the ASTM A36 type was utilized as the material in the computational study of the frame. The results show that increasing speed causes an increase in deformation, with the peak deformation at a speed of 100 km/h. The maximum deformation occurs at 0.007 seconds with a value of 203.51 mm at the top pillar of the car. The deformation increases from 97.196 mm at 0.0035 s to 161.22 mm at 0.0056 s. However, deformation occurs mainly in the front zone of the car frame and is not significant in the passenger zone.

19 January 2023 in EUREKA: Physics and Engineering
Verified
Journal Article
Open access
PDF file
RLRemon Lapisa
Remon Lapisa
AKAndre Kurniawan
Andre Kurniawan
JJJasman Jasman
Jasman Jasman
DYDori Yuvenda
Dori Yuvenda
RPRandi Purnama Putra
Randi Purnama Putra
KKKrismadinata Krismadinata
Krismadinata Krismadinata
This experimental study aims to investigate and analyze the performance of a Water-Air Heat Exchanger that functions as passive cooling in a building ventilation system in the tropics. Before being blown into the room, the high-temperature outdoor air will be passively cooled by the lower-temperature water. Air driven by an Inline Duct Fan with a constant mass flow rate of 4.68 cubic meters per minute flows through a PVC hose as a heat exchanger inserted into a full water reservoir with a diameter of 100 cm and a height of 110 cm. A heat exchanger hose with a diameter of 6.35 cm and a length of 4130 cm is installed in a spiral-circular manner with a total of 16 coils with a diameter of 80 cm to increase the heat transfer effectiveness between water and air. The passive cooling effectiveness is analyzed by decreasing the air temperature between the inlet and outlet of the ventilator after passing through the heat exchanger. The temperature, humidity, and daylight measurement data were carried out for 36 consecutive hours using a multichannel data logger at several locations; ventilator inlet, ventilator outlet, water in the tub, and outside air. The measurement results show that the designed water-to-air heat exchanger provides a significant passive cooling effect and can reduce air temperature to 6.88 °C. By utilizing the passive cooling effect, the cooling energy gain obtained during the measurement period in the ventilation system of this building is 8.3 kWh. The methodology and results of this research are expected to make a positive contribution to the development of the concept of energy-efficient buildings by using passive cooling techniques

29 March 2024 in EUREKA: Physics and Engineering
Verified
Journal Article
Open access
PDF file
RPRandi Purnama Putra
Randi Purnama Putra
SISutardi Sutardi ITS
Sutardi Sutardi ITS
WWWawan Aries Widodo
Wawan Aries Widodo
DYDori Yuvenda
Dori Yuvenda
RLRemon Lapisa
Remon Lapisa
DHDani Harmanto
Dani Harmanto
The ducting system is made up of 90° elbows and a few other fittings and accessories in addition to straight ducts. The friction loss, separation loss, and secondary flow loss are the main causes of the pressure decrease in an elbow, and they all increase with the presence of elbows. Utilizing too much energy to propel the flow is a cost associated with pressure loss. The aim of this research is to investigate turbulent flow via 90° square elbows and a square-sectioned duct through experimental methods by adding a circular turbulator (CT) close to the elbow wall's inner radius. The Reynolds numbers (ReDh) used in this research are 1.6×104, 4.8×104, and 9.5×104, with average flow velocities of 2 m/s, 6 m/s, and 12 m/s. Circular turbulators are added to the inner walls with angular positions (α) of 5°, 10°, 15°, and 20°. The results showed that the turbulence intensity increased toward the inner radius wall of the elbow in ducting with CT. For this study, the flow within the ducting with the CT is generally more turbulent than the flow inside the ducting without the CT. By including CT, it was possible to reduce the overall pressure loss in ducting with an elbow. The pressure reduction at two ReDh values (1.6×104 and 4.8×104) was only lessened by CT positioned at α=10°, 15°, and 20° out of the four CT placements. Conversely, CT positioned at α=5° can only effectively mitigate pressure decrease at ReDh=1.6×104. CT installation cannot lessen the pressure drop that happens in the ducting at a value of ReDh=9.5×104. CT placement at the three α values often helps to lower the pressure drop in the ducting. Using the CT, positioned at α=15°, is the greatest strategy to reduce the overall pressure decrease

30 November 2023 in EUREKA: Physics and Engineering
Verified
Journal Article
Open access
PDF file
RPRandi Purnama Putra
Randi Purnama Putra
WAWaskito
Waskito
DYDori Yuvenda
Dori Yuvenda
JAJunil Adri
Junil Adri
The extent of existing corn land in Indonesia and the activities carried out by farmers in corn farming requires the innovation of an effective and efficient corn harvesting machine. This underlies the Research Center for Appropriate Technology located at the Faculty of Engineering, Universitas Negeri Padang to design a corn harvesting tractor that can facilitate the community in carrying out activities in the agricultural sector. The design of the corn harvester tractor consists of the harvester mechanism, the frame, the engine, and the powertrain. The frame is a crucial component of the corn harvester tractor, and its strength depends on its shape and proportions. The construction's strength of the frame must take into account both safety considerations and the structure's strength. The purpose of this study is to evaluate the frame strength of a corn harvester tractor made of steel of the ASTM A36 type. In this study, the von Mises stress that exists in the frame is used to calculate the strength of the frame of a corn harvester tractor. In numerical analysis, the chassis utilizes two tests with various load variations, namely the concentrated load and the load that is evenly distributed on the surface. The simulation results show that the frame of the corn harvester tractor can withstand the load well. The results of the stress analysis that occurs on the frame of the corn harvester tractor are that the maximum stress that occurs due to the concentrated load on the frame is 3.248 MPa. While the maximum stress that occurs due to the distributed load acting on the frame is 3.510 MPa. In addition, information was obtained that the value of the safety factor for the frame with ASTM A36 type met the component requirements that could withstand concentrated loads and distributed loads