Pedro José de Castro

Pedro José de Castro

Auto-generated profile, based on publicly available information

Pedro José de Castro

Universidade Federal do Rio Grande do Sul, Brasil

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 May 2020 in Metals
Verified
Journal Article
Open access
PDF file
ASAntonio Carlos Silveira
Antonio Carlos Silveira
WBWilliam Lemos Bevilaqua
William Lemos Bevilaqua
VDVinicius Waechter Dias
Vinicius Waechter Dias
PCPedro José de Castro
Pedro José de Castro
Jeremy EppJeremy Epp
Jeremy Epp
ARAlexandre da Silva Rocha
Alexandre da Silva Rocha
Thermomechanical processing of low carbon bainitic steels is used to obtain a bainitic microstructure with good strength and toughness by continuous cooling after forging without the need of further heat treating, hence reducing manufacturing costs. However, hot forging parameters can significantly influence the microstructure in the forged material. A series of heat treating and forging experiments was carried out to analyze the effect of austenitizing time and temperature on the grain growth and the effect of forging temperature on the Prior Austenite Grain Size (PAGS) and continuously cooled microstructure. The forged microstructures were characterized by optical microscopy, microhardness tests, and X-ray diffraction. The results indicate that at 1200 °C austenitizing temperature abnormal grain growth takes place. Forging temperature significantly affects the PAGS and the subsequently formed microstructure. At high forging temperature (1200 °C), an almost fully bainitic microstructure was obtained. As the forging temperature was reduced to 1100 and 1000 °C, the PAGS refined, while the polygonal ferrite faction increased and the amount of retained austenite decreased. Further evaluations showed that a decrease in the forging temperature results in a higher carbon concentration in solution in the retained austenite leading to a stabilization effect.


1 January 2021 in Materials Research
Verified
Journal Article
Open access
PDF file
PCPedro José de Castro
Pedro José de Castro
ASAntonio Carlos Silveira
Antonio Carlos Silveira
TIThiago Marques Ivaniski
Thiago Marques Ivaniski
CTCristiano José Turra
Cristiano José Turra
JEJeremy Epp
Jeremy Epp
ARAlexandre da Silva Rocha
Alexandre da Silva Rocha
Thermo-mechanical treatments using continuous cooling after forging are an established method for producing bainitic steels, mainly because of the elimination of energy intensive additional heat treatment processes. The cooling is usually employed in an uncontrolled manner in the industrial sector, which can be detrimental to the resulting microstructural morphology and, consequently, to the final product properties. In this study, a new controlled two-step cooling route based on the principles of bainitic displacive growth was designed and applied in a 0.18C (wt-%) steel. Inverse finite element method was used on the cooling data to obtain the evolution of temperatures for the samples during cooling, allowing to assess point to point cooling rates. Investigations via X-ray diffraction, optical microscopy analysis and hardness testing revealed a variation of bainitic morphology, namely, the transition from granular bainite to lath-like bainite with relatively high hardness and constituents/phase boundaries than the pre-treated microstructure.

1 January 2022 in Materials Research
Verified
Journal Article
Open access
TIThiago Marques Ivaniski
Thiago Marques Ivaniski
PCP.J. de Castro
P.J. de Castro
DRD. Rodrigues
D. Rodrigues
JÉJ. Épp
J. Épp
RNR.M. Nunes
R.M. Nunes
ARAlexandre da Silva Rocha
Alexandre da Silva Rocha

1 January 2025 in REM - International Engineering Journal
Verified
Journal Article
Open access
PDF file
DRDouglas Rodrigues de Rodrigues
Douglas Rodrigues de Rodrigues
Rafael Luciano DalcinRafael Luciano Dalcin
Rafael Luciano Dalcin
Jeremy EppJeremy Epp
Jeremy Epp
PCPedro José de Castro
Pedro José de Castro
ASAntonio Carlos Silveira
Antonio Carlos Silveira
ARAlexandre da Silva Rocha
Alexandre da Silva Rocha
New processing routes and alternatives have been studied in the manufacture of automotive parts aiming for lower energy consumption and less environmental impact. In this context, continuous cooling bainitic steels have emerged to address this demand by eliminating the quenching and tempering treatments. In substitution to heat treatments to improve wear resistance on the surface, plasma nitriding is a candidate. However, the effects on the core of bainitic microstructures over long time processes at subcritical temperatures are limited and should be further investigated. Especially in case of unexpected effects on the core of steels depending on time and temperature, compromising performance in service. The aim of the present study was to evaluate the effects of two plasma nitriding conditions at 500 ºC on the core of DIN 18MnCrSiMo6-4 continuous cooling bainitic steel, for 20 h and 30 h of treatment. For this purpose, characterization techniques, such as optical microscopy and SEM were applied to evaluate microstructural changes on the core followed by the Vickers hardness test to estimate possible softening effects. The research found a decrease of austenite fraction in the nitride conditions in comparison to the initial microstructure of the bainitic steel, a reduction of dislocation density of ferrite measured by Williamson–Smallman relation and the hardness dropped about 10% after 20 h and 20% after 30 h of treatment. The conclusion pointed out alteration on the core for the plasma nitriding treatments for long time cycles at a temperature of 500 °C, similarly to effects observed in tempering treatments.