22 July 2019 in Nuclear Fusion
12 October 2020 in Journal of Analytical Atomic Spectrometry
The objective of the present study has been to evaluate the potential applications of picosecond laser-induced breakdown spectroscopy (ps-LIBS) in nuclear fusion devices. The laser-ablation behaviors and the spectral emission features of ps-LIBS at broad laser fluences have been investigated under a high vacuum using a 35 ps laser with λ = 355 nm in order to achieve high depth-resolution diagnosis of the key fusion-related material, tungsten (W). For the ablation behaviors, three ablation regimes in laser fluences have been clearly identified, both in terms of average ablation rate (AAR) changes and surface morphology variations. For the spectral emission features of ps-LIBS investigated utilizing CCD and ICCD spectrometers, the intensities of the continuum background and atomic lines emission showed the different rising tendencies with the laser fluence in these three ablation regimes. Three representative craters in the three ablation regimes were characterized by scanning electron microscopy (SEM) to investigate the crater morphologies and microstructures. The results for the ablation rates and spectral emission features as well as the crater morphologies suggest that the first ablation regime was a superior choice for the diagnosis of the W wall by ps-LIBS due to the limited AAR (<40 nm per pulse), the small thermal effect, and thus the potentially high depth-resolution capacity. Further, the AARs and spectral emission features of ps-LIBS as a function of the ablation crater diameter in the first ablation regime were systematically studied. The results demonstrate that the AAR was weakly dependent on the crater diameter when keeping the same laser fluence, while the spectral intensities of the ps-LIBS increased significantly with the crater diameter increasing. Moreover, a rectangle-like cross-section of the crater could be achieved in the first ablation regime. This has a unique benefit for depth analysis of the deposited layer on the first wall of nuclear fusion devices by ps-LIBS.
1 October 2019 in Spectrochimica Acta Part B: Atomic Spectroscopy
2 December 2021 in Nuclear Fusion
W7-X completed its plasma operation in hydrogen with island divertor and inertially cooled test divertor unit (TDU) made of graphite. A substantial set of plasma-facing components (PFCs), including in particular marker target elements, were extracted from the W7-X vessel and analysed post-mortem. The analysis provided key information about underlying plasma–surface interactions (PSI) processes, namely erosion, transport, and deposition as well as fuel retention in the graphite components. The net carbon (C) erosion and deposition distribution on the horizontal target (HT) and vertical target (VT) plates were quantified and related to the plasma time in standard divertor configuration with edge transform ι = 5/5, the dominant magnetic configuration of the two operational phases (OP) with TDU. The operation resulted in integrated high net C erosion rate of 2.8 mg s−1 in OP1.2B over 4809 plasma seconds. Boronisations reduced the net erosion on the HT by about a factor 5.4 with respect to OP1.2A owing to the suppression of oxygen (O). In the case of the VT, high peak net C erosion of 11 μm at the strike line was measured during OP1.2B which converts to 2.5 nm s−1 or 1.4 mg s−1 when related to the exposed area of the target plate and the operational time in standard divertor configuration. PSI modelling with ERO2.0 and WallDYN-3D is applied in an interpretative manner and reproduces the net C erosion and deposition pattern at the target plates determined by different post-mortem analysis techniques. This includes also the 13C tracer deposition from the last experiment of OP1.2B with local 13CH4 injection through a magnetic island in one half module. The experimental findings are used to predict the C erosion, transport, and deposition in the next campaigns aiming in long-pulse operation up to 1800 s and utilising the actively cooled carbon-fibre composite (CFC) divertor currently being installed. The CFC divertor has the same geometrical design as the TDU and extrapolation depends mainly on the applied plasma boundary. Extrapolation from campaign averaged information obtained in OP1.2B reveals a net erosion of 7.6 g per 1800 s for a typical W7-X attached divertor plasma in hydrogen.
1 October 2018 in Fusion Engineering and Design
1 June 2018 in Spectrochimica Acta Part B: Atomic Spectroscopy