Thomas Hantschel

Thomas Hantschel

Auto-generated profile, based on publicly available information

Thomas Hantschel

IMEC, Kapeldreef 75, Leuven, Flanders, 3001, BELGIUM

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 September 2020 in Scientific Reports
Verified
Journal Article
Open access
PDF file
KPKomal Pandey
Komal Pandey
KPKristof Paredis
Kristof Paredis
THThomas Hantschel
Thomas Hantschel
CDChris Drijbooms
Chris Drijbooms
WVWilfried Vandervorst
Wilfried Vandervorst
Scanning Spreading Resistance Microscopy is a well-established technique for obtaining quantitative two- and three-dimensional carrier profiles in semiconductor devices with sub-nm spatial resolution. However, for sub-100 nm devices, the use of focused ion beam becomes inevitable for exposing the region of interest on a sample cross section. In this work, we investigate the impact of the focused ion beam milling on spreading resistance analysis and we show that the electrical effect of the focused ion beam extends far beyond the amorphous region and depends on the dopant concentration, ion beam energy, impact angle, and current density. For example, for dopant concentrations between 1.0 × 1020 and 1.5 × 1016 cm−3 we observe dopant deactivation at least between 23 and 175 nm for a glancing 30 keV ion beam. Further, we show that dopant deactivation is caused by defect diffusion during milling and is not directly impacted by the presence of Gallium in the sample. Later, we also discuss potential ways to mitigate these effects.

8 October 2025 in Applied Physics Reviews
Verified
Journal Article
Closed access
ALAshiqur Rahman Laskar
Ashiqur Rahman Laskar
LWLennaert Wouters
Lennaert Wouters
PLPieter Lagrain
Pieter Lagrain
JSJill Serron
Jill Serron
NPNemanja Peric
Nemanja Peric
UCUmberto Celano
Umberto Celano
Scanning spreading resistance microscopy (SSRM) has recently celebrated 30 years of existence when counting from the original patent of 1994. In this time, the technique has experienced an incredible journey with substantial evolutions that transformed SSRM from a small-scale experiment into a staple for chip manufacturing laboratories for physical analysis of materials, failure analysis, and process development of integrated circuits. As the nanoelectronics industry is ready for a new inflection point, with the introduction of nanosheet field-effect transistor to replace FinFETs and cell track scaling architectures such as the complementary field-effect transistors, SSRM is once again at a turning point. This review aims to highlight the state-of-the-art while discussing the emerging challenges introduced by the ever-increasing complexity in complementary metal–oxide–semiconductor (CMOS) manufacturing. We start by illustrating the unique capability of the SSRM technique, its origin, and its evolution. Next, we continue by showing the considerable research effort that enabled SSRM to transition to a tomographic sensing method in support of FinFET transistors. Here, the high aspect ratio fin geometry and the complex contacts technology have imposed important modifications to the original method. Later, we elaborate on some of the key challenges introduced by the upcoming device transition from three-sided channel FinFETs into nanosheet FETs, i.e., offering a four-sided electrostatic control of the channel. Finally, we present the use of machine learning for automation in carrier calibration with increased accuracy. We close by introducing some of the concepts that we consider promising for further extension of SSRM to obtain sub-nm structural information and doping profiles in the area of advanced FinFETs and nanosheet FET technologies, including (a) correlative analysis flow, (b) liquid-assisted probing, and (c) top–down and bottom–up multi-probe sensing schemes to merge low- and high-pressure SSRM scans.

1 June 2014 in Microelectronic Engineering
Verified
Journal Article
Closed access
THT. Hantschel
T. Hantschel
TCT. Clarysse
T. Clarysse
AAA. Ajaykumar
A. Ajaykumar
FSFelix C Seidel
Felix C Seidel
MTM. Tsigkourakos
M. Tsigkourakos
WVW. Vandervorst
W. Vandervorst

1 September 2012 in Microelectronic Engineering
Verified
Journal Article
Closed access
THT. Hantschel
T. Hantschel
ASA. Schulze
A. Schulze
UCUmberto Celano
Umberto Celano
AMA. Moussa
A. Moussa
KAKai Arstila
Kai Arstila
WVW. Vandervorst
W. Vandervorst

1 January 2010
Verified
Conference Paper
Closed access
PDF file
EME. Mavridou
E. Mavridou
MWM.C. de Lind van Wijngaarden
M.C. de Lind van Wijngaarden
AKA.I. Kauerauf
A.I. Kauerauf
THT. Hantschel
T. Hantschel
KKK. Kornpihl
K. Kornpihl
IBI. Bryant
I. Bryant

9 April 2024 in Nanotechnology
Verified
Journal Article
Open access
HKHyeon-Su Kim
Hyeon-Su Kim
NPNemanja Peric
Nemanja Peric
AMAlbert Minj
Albert Minj
LWLennaert Wouters
Lennaert Wouters
JSJill Serron
Jill Serron
THThomas Hantschel
Thomas Hantschel
We introduce a new scanning probe microscopy (SPM) concept called reverse tip sample scanning probe microscopy (RTS SPM), where the tip and sample positions are reversed as compared to traditional SPM. The main benefit of RTS SPM over the standard SPM configuration is that it allows for simple and fast tip changes. This overcomes two major limitations of SPM which are slow data acquisition and a strong dependency of the data on the tip condition. A probe chip with thousands of sharp integrated tips is the basis of our concept. We have developed a nanofabrication protocol for Si based probe chips and their functionalization with metal and diamond coatings, evaluated our probe chips for various RTS SPM applications (multi-tip imaging, SPM tomography, and correlative SPM), and showed the high potential of the RTS SPM concept.