27 November 2023 in IEEE Transactions on Power Electronics
A wide-input/output-voltage-range buck converter with adaptive light-load efficiency improvement and seamless mode transition for high-voltage applications is presented in this article. The proposed design uses a load prediction structure to eliminate dc current sensor and to ensure high efficiency in the 0.02 $\sim$ 2-A load range. The pulsewidth modulation (PWM) mode has been used for near-full load. Since efficiency degradation at light loads occurs at different levels regarding the input and output voltage, a novel dynamic frequency pulsewidth modulation (DFPWM) with adaptive efficiency improvement mechanism is proposed, which activates efficiency improvement based on the input and output voltage at proper load current. Moreover, pulse frequency modulation (PFM) has been used to guarantee high efficiency in a wider load range. The proposed trimode buck converter has seamless mode change. Input and output voltage ranges are 5 $\sim$ 30 V and 3 $\sim$ 15 V, respectively, which are compatible with automotive and RF applications. Output voltage disturbance is less than 60 mV at 2-A load step with a 15- $\mu$ s settling time for 30 to 3 V conversion. Moreover, output voltage disturbance in PWM/DFPWM and DFPWM/PFM mode change is zero and 60 mV, respectively. The proposed design has been implemented on 180-nm BCD technology with a 1.65 mm ×1.80 mm die size.
20 January 2020 in IEEE Transactions on Instrumentation and Measurement
Low power wireless standalone sensors which can operate without any wiring have received significant attention in sensor network applications. These devices harvest environmental energy resources to supply their power and transfer their collected data using wireless RF links. In many instances the power supplied from the environment is far less than the power required by the sensor device. In this case the main solution is to accumulate energy on a storage element and when enough energy is stored, the sensor node is instantaneously activated using an under voltage lockout, UVLO, circuit. During this short time burst, the sensor performs the required acquisition, transmits the results and enters a sleep mode until again enough energy is collected. The quiescent current of the UVLO is the main factor that determines the minimum power level at which the sensor node is still operational. Most wake-up circuits used in conventional devices suffer from a quiescent current of a few hundred nanoamperes. In this work, using a zero bias current MOSFET based approach, a new wake-up circuitry is presented which lowers the quiescent current down to the picoampere range. As a practical application, the effectiveness of the proposed circuit is shown in a soil moisture monitoring sensor setup.
21 November 2023 in IEEE Transactions on Power Electronics
An ultra-low-noise buck converter for noise-sensitive applications is presented, which utilizes a novel pseudo average current-mode control (ACMC) with an adaptive ramp generator to decrease the baseband noise. Also, in order to suppress electromagnetic interference (EMI) and high-frequency spurs, spread spectrum and secondary filter are used, respectively. The proposed ACMC buck converter suppresses the switching frequency perturbation effect on the output voltage, and as a result in the spread spectrum condition, only a small amount of noise is added to the output voltage in the baseband frequency. For the spread spectrum with an external clock, a phase-locked loop is used, which synchronizes the internal oscillator and adapts the ramp generator slope to suppress spread spectrum baseband noise. The proposed ACMC converter achieves only 58 $\mu V_\mathrm{rms}$ noise in 100 Hz–100 kHz frequency range. Also, a $\pm$ 10% random spread spectrum architecture suppresses the EMI level by 11 dB while achieving only 88 $\mu V_\mathrm{rms}$ and 156 $\mu V_\mathrm{rms}$ noise for internal and external clock synchronization, respectively. The peak efficiency of the converter is 95% and the output voltage disturbance is 100 mV at a 2-A load step with 16 $\mu$ s settling time. The proposed design is implemented on a 180-nm BCD technology occupying a 1.65×3.70 mm $^{2}$ die size.
14 November 2024 in IEEE Transactions on Power Electronics
An ultrafast step response synchronous buck converter has been developed for battery-powered and hand-held electronic applications. The proposed converter has an impressive settling time of only two clock periods and a 1.8 A output current capability. This fast step response makes the proposed converter an ideal choice for dynamic voltage scaling technique in the mentioned applications. The proposed design utilizes an analog multiplier controller (AMC), which provides an optimum disturbance-damping mechanism to remove any output voltage error in just two clock periods. In addition, the synchronization feature of the AMC buck converter eliminates the electromagnetic interference concern in fast buck converters. In order to realize the proposed controller a multiplier block and a novel residual time generator block are employed. The proposed AMC buck converter achieves a fast 2–2.3 $\mu s$ settling time for 1.3 A load step and a 3–3.5 $\mu s$ settling time for 1 V reference step with 1 MHz of switching frequency. Furthermore, The AMC buck converter has a high output current density of 1.38 A/mm$^{2}$ with 96$\%$ peak efficiency. The proposed design has been implemented in a 180 nm bipolar-CMOS-DMOS (BCD) technology with a die size of 910 $\mu$m × 1500 $\mu$m.
15 September 2025 in IEEE Journal of Solid-State Circuits
This article introduces a novel resetting oscillator regulator (ROR) control method for low-dropout (LDO) regulators, designed to achieve fast settling times for both load and reference input steps. The proposed ROR integrates a high-speed loop that independently functions as an oscillator in a closed-loop configuration, along with a separate high-rate resetting oscillator. The resetting oscillator reinitializes the internal nodes of the ROR loop, preventing oscillations and enabling the system to function as a high-speed regulator. Compared to prior works, the proposed ROR demonstrates improved load and reference step response speeds while maintaining a simple implementation. Fabricated using a 0.18- $\boldsymbol {\mu }$ m CMOS process, the ROR achieves fast settling times of 15 ns for low-to-high and high-to-low reference steps. It also demonstrates settling times of $25\sim 30$ ns for a 400-mA load step, utilizing an integrated 50-pF output capacitor. The ROR consumes only $130~\boldsymbol {\mu }$ A of quiescent current and supports a maximum output current capability of 500 mA. The input and output voltage ranges of the proposed ROR are $1.5\sim 1.8$ V and $0.9\sim 1.6$ V, respectively. In addition, the regulator exhibits a low output ripple of $0.3~\mathbf {mV}_{\text {rms}}$ , occupies a compact active area of only $0.08~\mathbf {mm}^{2}$ and achieves a low 3.2-fs figure of merit (FOM $\mathbf {_{T}}$ ).