This paper presents a cost-effective approach for the template-assisted electrodeposition fabrication of substrates for surface-enhanced Raman scattering (SERS) with metal nanowires (NWs) grown in pores of polymer track-etched membranes (TM). This technique allows the synthesis of NWs array with its certain surface density and diameter (from dozen to hundreds of nm). NWs length also may be varied (order of μm) by controlling deposition time. Here we grow vertical Ag-NWs which are leaning towards their nearest neighbors, forming self-assembled bundles whose parameters depend on the NW aspect ratio (length to diameter). We show that in such bundles there are “hot spots” in the nm-gaps between NWs tips. Computer simulations have demonstrated a strong enhancement of the electric field within these hot spots; thus, the Raman signal is markedly amplified for analyte molecules placed directly inside the gaps. We have experimentally proved the potential of this SERS-technique on the example of 4-Mercaptophenylboronic acid (4-MPBA). For 4-MPBA the maximal enhancement of Raman signal was found at NWs length of ~1.6 μm and diameter of ~100 nm. The effect is higher (up to twice) if “wet” substrate is used just immediately after the TM polymer removal so that the tips are brought to lean after analyte exposure. We suggest this new type of nanostructured SERS-substrates as a base of effective sensing of extremely low concentration of analytes.
An antenna array with short shielded transverse electromagnetic horns (S-TEM-horns) for emitting high-power radiation of ultra-short electromagnetic pulses (USEMP) has been created and researched. The antenna unit consists of an ultra-wideband antenna array with four S-TEM horns, with each connected to a two-wire HF transmission line, and these four lines are connected to an antenna feeder. This feeder is connected to a semiconductor generator with the following parameters: a 50 Ohm connector, 10–100 kV high-voltage monopolar pulses, a rise time of about 0.1 ns, FWHM = 0.2–1 ns, and pulse repetition rates of 1–100 kHz. The antenna array was designed and optimized to achieve a high efficiency of about 100% for the antenna aperture by using a 2 × 2 array with S-TEM-horns, with shielding rectangular plates for the return current. The transient responses were studied by simulation using the electromagnetic 3D code “KARAT” at the time domain and experimentally with the use of our stripline sensor for measurement of the impulse electrical field with a 0.03 ns rise time and a 7 ns duration at the traveling wave. The radiators were emitting USEMP waves with a hyperband frequency spectrum of 0.1–6 GHz. The radiation with an amplitude of 5–30 kV/m of the E-field strength at a distance of up to 20 m was successfully applied to test the electronics for immunity to electromagnetic interference.
Accumulation of oscillating electrons in an electron-string ion source is simulated by the particle-in-cell method. The electrons are accumulated in a long trap into which an electron beam is injected. It is shown that a chain of alternating phase holes and squeezed states forms in the trap. The dynamical features of such a longitudinal structure, such as the double-pulse waveform and strong high-frequency oscillations of the accumulation current and the broadening of the electron distribution function, are qualitatively similar to those previously observed in experiments with the Krion-2 ion source operating in the electron-string mode.
This article presents time-dependent numerical modeling of V-band relativistic orotron: a high-power microwave generator with a TM03 oscillation mode in an oversized (D/λ ∼ 2.7) electrodynamic structure and diffractive output in the TM02 mode. Single-mode operation of the oscillator is ensured by the cyclotron selection of the working axisymmetric mode, with simultaneous depression of competing non-axisymmetric modes by means of cutting longitudinal slits in the wall of the slow-wave structure. The simulated output microwave power is 350 MW with a power conversion efficiency of 31% when using a 3.6 kA, 310 keV electron beam transported in the 3.9 T magnetic field. The simulation employed 2.5D axisymmetric and 3D Cartesian versions of the KARAT code.
We present the results of experiments on the aneutronic fusion of proton-boron (pB) in a single miniature device with electrodynamic (oscillatory) plasma confinement. The device is based on a low energy nanosecond vacuum discharge with a virtual cathode, the field of which accelerates protons and boron ions to the energies required for pB synthesis under oscillating ions' head-on collisions. The yields of particles registered for different conditions of the experiment are presented and discussed in detail. The experiment was preceded by particle-in-cell modeling of main processes accompanying pB reaction within the framework of the full electromagnetic code karat. The summary yield of particles of about was obtained during the pulse-periodic operation of the generator within total of the high voltage applied, which is particles/ns.
We demonstrate the possibility of chaotic millimeter wave generation in broadband helical-waveguide gyrotron travelling wave tubes (gyro-TWTs) by introducing external delayed feedback. It is shown that for the realization of “developed” chaos the amplitude characteristic of the amplifier should have the maximum slope in the overdrive regime upon saturation. This can be achieved by proper choosing of cyclotron resonance detuning. According to the time-domain averaged model and 3D particle-in-cell simulations with the parameters of the experimentally realized 35 GHz gyro-TWT, the power of chaotic generation can achieve 50 kW for an electron mean efficiency of about 7% and a spectrum width of 3–4 GHz.