The creation of supercapacitors with superior energy density and power capabilities is critical for advanced energy storage solutions. Ionic liquid electrolytes offer a promising alternative in this respect. However, improving their cycle stability and efficiency is a complex task requiring extensive research and significant effort. The high viscosity of ionic liquids (ILs) limits their lifetime, but this can be mitigated by increasing the temperature or adding solvents. In this research, the electrochemical performance of symmetric activated carbon supercapacitors with 1-Ethyl-3-methylimidazolium tetrafluoroborate (EMIMBF4) and different ratios of acetonitrile (ACN) as electrolytes were investigated. Long-term galvanostatic charge/discharge tests, impedance studies, and cyclic voltammetry were performed at temperatures between 24 to 60 °C. The addition of ACN to the ionic liquid increased electrochemical stability and reduced internal resistance, with the best performance observed at a 1:2 volume ratio of EMIMBF4 to ACN. This supercapacitor exhibited 87% cyclic stability after 5000 charge/discharge cycles in the voltage range of 0.05–2.8 V and a current rate of 1 Ag−1. It also achieved an energy density of 23 Whkg−1 and a power density of 748 Wkg−1. The supercapacitors were stable at elevated temperatures up to 60 °C, showing no degradation after operation under various thermal conditions.
In this study, the potential to modify the phase structure and morphology of manganese dioxide synthesized via the hydrothermal route was explored. A series of samples were prepared at different synthesis temperatures (100, 120, 140, and 160 °C) using KMnO4 and MnSO4·H2O as precursors. The phase composition and morphology of the materials were analyzed using various physicochemical methods. The results showed that, at the lowest synthesis temperature (100 °C), an intercalation compound with composition K1.39Mn3O6 and a very small amount of α-MnO2 was formed. At higher temperatures (120–160 °C), the amount of α-MnO2 increased, indicating the formation of two clearly distinguished crystal structures. The sample obtained at 160 °C exhibited the highest specific surface area (approximately 157 m2/g). These two-phase (α-MnO2/K1.39Mn3O6) materials, synthesized at the lowest and highest temperatures, respectively, and containing an appropriate amount of carbon xerogel, were tested as active mass for positive electrodes in a solid-state supercapacitor, using a Na+-form Aquivion® membrane as the polymer electrolyte. The electrochemical evaluation showed that the composite with the higher specific surface area, containing 75% manganese dioxide, demonstrated improved characteristics, including 96% capacitance retention after 5000 charge/discharge cycles and high energy efficiency (approximately 99%). These properties highlight its potential for application in solid-state supercapacitors.
Combining carbon materials with oxides in a hybrid electrode is an effective way to control supercapacitor performance in terms of balancing energy and power density with cycling stability. However, it is still unclear how the mixing method of each component affects the supercapacitor performance. In this study, the influence of mixing reduced graphene oxide (rGO) with ilmenite-type nickel-manganese oxide (NiMnO3) on the capacitive behaviour of the resulting composites is investigated. Two preparation methods are compared: mechanical mixing and ultrasonication. The capacitive characteristics were evaluated in hybrid supercapacitors using 6M KOH electrolyte. The bulk, surface, and morphological changes of the composites after long-term cycling were probed by EIS and ex situ XRD, XPS, and SEM analyses. It is established that the composites obtained by mechanical mixing exhibit better performance due to the stable contact between rGO and NiMnO3 particles, favourable surface reactions with KOH and preserved morphology of rGO. These findings indicate that efficient hybrid electrodes can be achieved without relying on costly synthesis techniques such as hydrothermal or ultrasonic treatments.
The development of low-cost, environmentally friendly, and electrochemically stable electrode materials remains a significant challenge for supercapacitors. In the present study, composite materials based on a montmorillonite K10 clay support were synthesized and characterized. Coconut shell-derived activated carbon, manganese dioxide (MnO2), and/or activated carbon (YP-80F) modified with silver nanoparticles were utilized as functional additives to the clay matrix. The aim of this work is to enhance the specific capacitance and electrochemical stability of the materials through a synergistic effect between these individual components. The novelty of this study lies in the integration of montmorillonite K10-based nanocomposites with an ion-exchange hydrogel membrane and in the investigation of the synergistic effects of different functional additives on the electrochemical performance of supercapacitors. The electrodes were fabricated using a casting method, while a commercial membrane, pre-soaked in a sodium sulfate solution, was employed as both separator and electrolyte. The membrane functions as an ion-exchange hydrogel, contributing to high ionic conductivity and reduced interfacial resistance. The electrochemical results indicate that the presence of additives significantly improves electron transport within the system, while the K10 clay support acts as a stable structural framework. The obtained results demonstrate the potential of clay-based nanocomposites integrated into gel-polymer systems for the development of efficient, low-cost, and environmentally friendly next-generation supercapacitors.