We show that a multilayer analysis of the infrared -axis response of provides important new information about the anomalous normal-state properties of underdoped cuprate high temperature superconductors. In addition to competing correlations which give rise to a pseudogap that depletes the low-energy electronic states below , it enables us to identify the onset of a precursor superconducting state below . We map out the doping phase diagram of which reaches a maximum of 180 K at strong underdoping and present magnetic field dependent data which confirm our conclusions.
We report on the behavior of a high-Tc superconducting (HTS) homopolar dynamo which outputs a DC open-circuit voltage when the stator is in the superconducting state, but behaves as a conventional AC alternator when the stator is in the normal state. We observe that this time-averaged DC voltage arises from a change in the shape of the AC voltage waveform that is obtained from a normal conducting stator. The measured DC voltage is proportional to frequency, and decreases with increasing flux gap between the rotor magnet and the HTS stator wire. We observe that the DC output voltage decreases to zero at large flux gaps, although small differences between the normal-conducting and superconducting waveforms are still observed, which we attribute to screening currents in the HTS stator wire. Importantly, the normalised pulse shape is found to be a function of the rotor position angle only. Based on these observations, we suggest that the origin of this unexpected DC effect can be explained by a model first proposed by Giaever, which considers the impact of time-varying circulating eddy currents within the HTS stator wire. Such circulating currents form a superconducting shunt path which “short-circuits” the high field region directly beneath the rotor magnet, at those points in the cycle when the rotor magnet partially overlaps the superconducting stator wire. This reduces the output voltage from the device during these periods of the rotor cycle, leading to partial rectification of the output voltage waveform and hence the emergence of a time-averaged DC voltage.
One of the central themes in cuprate superconductivity is the evolution of the electronic properties with the charge carrier concentration, p, expressed as the number of holes per Cu ion in the CuO2 planes. In YBa2Cu3O7−δ (YBCO), p is well known to vary with oxygen content (δ) and with substitution of Ca2+ for Y3+. In this Letter, we show that p also varies with the fraction of Cu–O “chain layer” stacking faults. The resulting parabolic variation in the superconducting transition temperature (Tc) is also well known; however, the effect on the critical current density (Jc) is less well explored. We show that the self-field Jc follows a common trend for all these hole doping methods, rising to a sharp peak on the slightly overdoped side of the Tc(p) parabola. In contrast, the in-field Jc anisotropy at high temperatures and low fields is determined solely by the stacking-fault fraction, not by hole doping, such that a sample free from stacking faults tends towards an isotropic Jc. These results serve to emphasize the role of sample microstructure in determining Jc in-field anisotropy.
We show theoretically that phase and amplitude fluctuations set in simultaneously in the cuprates. We then analyze fluctuations about Tc in the specific heat of (Y,Ca)Ba2Cu3O7-$\delta${}, YBa2Cu4O8, and Bi2Sr2CaCu2O8+$\delta${}. The mean-field transition temperature, Tcmf, in the absence of fluctuations lies well above Tc and at low doping reaches as high as 150 K. Tcmf is found to be unrelated to the pseudogap temperature T*, but scales with the gap $\Delta${}0, such that 2$\Delta${}0/kBTcmf is comparable to the BCS weak-coupling value 4.3, for d-wave superconductivity.
6 February 2023 in IEEE Transactions on Applied Superconductivity
A 100 kW, 4500 RPM synchronous superconducting motor is being built at the Paihau-Robinson Research Institute, Victoria University of Wellington, New Zealand. The motor has superconducting excitation field coils on the rotor and a conventional stator winding. To minimize mass the motor is an air-core type, meaning no ferromagnetic materials are employed inside the motor. Some of the salient features of this motor include: 1) field winding coils employing REBCO CORC conductor; 2) field coils powered with a contactless superconducting dynamo exciter; 3) an EM shield on the rotor for protecting the field coils from high frequency magnetic fields due to stator harmonics and the switching of the drive electronics; 4) a unique single-layer winding design for the stator winding, where the stator coils are made with copper Litz wire and are liquid-cooled. This paper describes the electrical design and 3D simulation of the motor including the superconducting dynamo, and highlights stator and rotor coil developments that will be validated in the prototype. Sensitivity to critical design parameters has been assessed in simulation and initial sub-system prototypes manufactured for testing. Preliminary design is projecting this motor diameter and axial length as 360 mm and 550 mm respectively, with an efficiency of 96.4% at the rated load. These numbers may be comparable with permanent magnet motors of similar rating, but this motor is being built to serve as a test-bed for evaluating different technologies for rotor and stator components. The ultimate goal for this program is a 3.0 MW machine with superconducting armature and field windings. In comparison with the permanent magnet motor in 2.5--3.0 MW range, the superconducting motors are expected to be 4 to 5 times smaller in size and mass with efficiency exceeding 99%.