A 100 kW, 4500 RPM synchronous superconducting motor is being built at the Paihau-Robinson Research Institute, Victoria University of Wellington, New Zealand. The motor has superconducting excitation field coils on the rotor and a conventional stator winding. To minimize mass the motor is an air-core type, meaning no ferromagnetic materials are employed inside the motor. Some of the salient features of this motor include: 1) field winding coils employing REBCO CORC conductor; 2) field coils powered with a contactless superconducting dynamo exciter; 3) an EM shield on the rotor for protecting the field coils from high frequency magnetic fields due to stator harmonics and the switching of the drive electronics; 4) a unique single-layer winding design for the stator winding, where the stator coils are made with copper Litz wire and are liquid-cooled. This paper describes the electrical design and 3D simulation of the motor including the superconducting dynamo, and highlights stator and rotor coil developments that will be validated in the prototype. Sensitivity to critical design parameters has been assessed in simulation and initial sub-system prototypes manufactured for testing. Preliminary design is projecting this motor diameter and axial length as 360 mm and 550 mm respectively, with an efficiency of 96.4% at the rated load. These numbers may be comparable with permanent magnet motors of similar rating, but this motor is being built to serve as a test-bed for evaluating different technologies for rotor and stator components. The ultimate goal for this program is a 3.0 MW machine with superconducting armature and field windings. In comparison with the permanent magnet motor in 2.5--3.0 MW range, the superconducting motors are expected to be 4 to 5 times smaller in size and mass with efficiency exceeding 99%.
Superconducting electric motors are required in order to deliver lower-carbon aviation. Critical to the success and viability of operating superconducting electric motors in aviation is keeping the superconducting coils at their operating temperature. This paper examines the challenges of keeping a superconducting motor cold if it were used on a single aisle passenger aircraft such as an Airbus A320. The cooling problem is defined and different cooling scenarios are investigated to determine viability. The investigation has shown that for a motor with a superconducting rotor only (copper stator), a Stirling-type cryocooler would be sufficient. However, if the motor is to be fully superconducting, then the cooling loads of the stator, which are much higher, make mechanical refrigeration impractical and the only option is to cool the motor with the heat sink of a liquid hydrogen fuel.
28 November 2024 in IEEE Transactions on Applied Superconductivity
The global demand for green hydrogen (H $_{2}$ ) is forecast to grow as economies transition away from fossil fuels. Off-shore wind farms are well-suited for H $_{2}$ production by electrolysis because they have access to a large and consistent source of renewable energy. Next-generation wind turbine designs are pushing ratings above 20 MW, where superconductors can help reduce the size and increase the efficiency of the generators. This paper describes a concept design for a 25 MW partially superconducting wind power generator intended for self-contained offshore production of green hydrogen. The generator features a high-temperature superconductor rotor energized by flux pump brushless exciters, and copper armature stator windings. Both rotor and stator are constructed in modular quadrants that can be factory-tested prior to transportation by road to the site. Each quad unit has its own superconducting coils, cryostat, cooling, and current sources. The modules are assembled to form the generator unit at the site, and can also be serviced or replaced individually, adding significant flexibility and robustness to generator operation.
7 September 2023 in Superconductor Science and Technology
Superconducting electric motors offer the potential for low weight and high power in applications such as electric aircraft and high speed marine transport. Combined with renewably-sourced cryogenic fuels and advanced fuel cells they offer a path to zero-carbon mass transport. The proposed architectures of these extreme machines, operating at temperatures around 20 K–50 K and employing very high alternating magnetic fields, require materials for the stator that are not electrically conducting and at the same time have good cryogenic structural performance. Additively manufactured (AM) materials can play a key role in these designs, and a collaboration between the Robinson Research Institute and Auckland University of Technology is studying the performance of a range of composite polymers in superconducting machine applications. There are significant challenges to be met, including understanding the effect of the build process on material properties at low temperatures, and also the effect of formulation changes on thermal properties. AM metals can be employed in the rotor components, where the magnetic field fluctuations are very small for our synchronous designs. In this usage case, we can achieve dramatic reductions in the weight of the rotor assembly by minimising the number of joints and facilitating the design of multi-functional components in our helium cooled, vacuum cryostat architecture. Novel design solutions have been developed for several key components in our prototype machines and these are discussed, along with cryogenic testing results for selected AM polymers and composites.
23 March 2023 in IEEE Transactions on Applied Superconductivity
The Robinson Research Institute at Victoria University Wellington is building a series of superconducting motors over the next six years to demonstrate technology pathways for the transport industry, including aviation. Our target topology for these machines uses rotor-mounted superconducting field coils and a superconducting stator in an air-core configuration. To avoid eddy current heating in the stator cryostat, electrically conductive materials must be eliminated. At the same time, heat generated due to AC losses in the stator must be transferred efficiently and evenly from the superconductor to the cryo-coolant, in order to avoid localised film boiling. And finally, the coil structural support needs to closely match the thermal expansion characteristics of the superconductor wires and likely other G10 structural pieces to avoid debilitating stresses and lost support. In this study, we investigated the opportunity to use additively manufactured (AM) polymers with a range of filler materials as the structural support for a motor coil. A range of commercially available candidate materials have been identified and test coupons manufactured using either Selective Laser Sintering (SLS) or Fused Deposition Modelling (FDM). The material properties of the test coupons have been measured from room temperature down to cryogenic temperatures. This data was used to design, analyse and manufacture the support structure for a stator saddle-coil, and the coil wound with aluminium wire to simulate Conductor on Round Core (CORC) cable. Initial thermal cycle testing has been carried out to assess the performance of the composite.
7 May 2025 in IEEE Transactions on Applied Superconductivity
High-speed, high-power-density generators capable of being directly coupled to a gas turbine engine are needed in the multimegawatt class for power generation aboard hybrid-electric aircraft and ships. Here, we present a homopolar generator concept featuring dual stationary rare earth barium copper oxide (REBCO) high-temperature superconductor field coils, one at each end of the machine, and a mass-optimized rotor consisting of discrete pole pieces. The location of the field coils permits easy access for servicing or replacement, and enhances flux concentration along the active length. The design produces a calculated rated power of 5.5 MW with 97.6% efficiency at 8000 r/min, corresponding to a power density of 3.5 kW/kg.