Junfeng Gui

Junfeng Gui

Auto-generated profile, based on publicly available information

Junfeng Gui

College of Electrical Engineering, Beijing Jiaotong University, Beijing, China

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 August 2025 in IEEE Sensors Journal
Verified
Journal Article
Closed access
ZLZhihao Li
Zhihao Li
RLRuifang Liu
Ruifang Liu
YHYali Hao
Yali Hao
DZDayong Zheng
Dayong Zheng
JGJunfeng Gui
Junfeng Gui
Electrical erosion caused by bearing currents is one of the main reasons for bearing failure in inverter-fed motors. The research of non-intrusive measurement of bearing currents contributes to risk assessment and early warning of bearing electrical erosion in electric motors, thereby enhancing the reliability of motor drive systems. This paper proposes a novel non-intrusive measurement method of bearing currents by measuring external electrical signals (bearing voltage and common-mode currents). Firstly, the relationship between bearing currents, bearing voltage, and common-mode (CM) currents is analyzed based on the CM model of the motor. Subsequently, the bearing voltage and CM currents are measured to detect and extract the characteristic signals induced by the discharge of the bearing oil film. The bearing voltage characteristic signals are detected using the instantaneous rate of change, while the CM current characteristic signals are extracted through a time-frequency features clustering method. The time-domain waveform of bearing currents is estimated by using the relationship between bearing currents and measured signals. Finally, the accuracy and effectiveness of the proposed method are verified by comparison with the intrusive measurement method. The proposed method demonstrates higher accuracy and reliability than traditional non-intrusive measurement methods.

2 October 2024
Verified
Book Chapter
Open access
PDF file
YCYanping Chang
Yanping Chang
PDPengjun Dang
Pengjun Dang
XLXuesong Liu
Xuesong Liu
YSYunhui Shi
Yunhui Shi
JCJingren Chang
Jingren Chang
JGJunfeng Gui
Junfeng Gui
Aiming at the problems of single power optimization in actual industrial parks without considering environmental factors, a method for optimal power allocation to industrial park users based on carbon emissions is proposed. Firstly, a multi-objective power optimization model is established, which includes the economic benefit objective of comprehensive power generation cost and the environmental benefit objectives of peak-to-valley difference and carbon emission. Secondly, the improved particle swarm algorithm is used for multi-objective optimization solving, combining the traditional particle swarm algorithm with the immunity principle, replacing subjective weights with objective assignments, and avoiding the local optimum problem. Finally, the load data of some users in the industrial park are brought in and the data indicators before and after optimization of the park are compared and analysed.

12 March 2026 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
CLChe Li
Che Li
XWXilian Wang
Xilian Wang
ZHZhuliang Huang
Zhuliang Huang
RYRuikang Yang
Ruikang Yang
JGJunfeng Gui
Junfeng Gui
The article proposes a model predictive suspension force control (MPSFC) to suppress the rotor’s radial displacement of bearingless switched reluctance motor (BSRM) during suspension. It can handle the complex coupling between the torque and suspension systems and between suspension forces in multiple directions which exhibit time-varying characteristics. Within each control step, model predictive control (MPC) will be first implemented for the torque system, where the predicted torque winding current can be obtained to achieve decoupling between the torque winding and the suspension winding with the mutual inductance model. Then, the suspension winding current and suspension force will be predicted sequentially through the prediction model considering one-step delay compensation. The concept of suspension force vector (SFV) is also proposed in this article to present the combined effect of mutually coupled suspension forces. The optimal control voltage vector will be selected by cost function to minimize the deviation between the predictive SFV and the desired one. The experiment results on a three-phase 12/8 BSRM demonstrate the proposed method can significantly reduce the energy consumption and radial displacement of the rotor and achieve robust suspension under low speed and external interference.

1 January 2026 in IEEE Transactions on Transportation Electrification
Verified
Journal Article
Closed access
RYRuikang Yang
Ruikang Yang
XWXilian Wang
Xilian Wang
JGJunfeng Gui
Junfeng Gui
ZHZhuliang Huang
Zhuliang Huang
CLChe Li
Che Li
JZJinhan Zhou
Jinhan Zhou