23 September 2025 in IEEE Journal of Solid-State Circuits
Conventional digital polar transmitters (TXs) suffer from limited power efficiency and linearity due to the multi-bit nature of intermediate signals. This work proposes a digital polar TX architecture that avoids such drawbacks by reducing the bit count of TX signals. The proposed TX oversamples and quantizes multi-bit I/Q inputs into three-level signals using simple delta-sigma modulators (DSMs), followed by a nine-state lookup table (LUT) to directly generate amplitude modulation (AM) and phase modulation (PM) signals. The complex coordinate rotation digital computer (CORDIC) that is widely used in polar TXs is not required. The AM signal is truncated to two levels for on/off control of an intrinsically linear 1-bit power amplifier (PA). The PA avoids the linearity and switching loss issues of conventional switched-capacitor PAs (SCPAs). The PM signal is represented with 3 bits for eight-phase generation via edge selection from a $4\times $ carrier local oscillator (LO), which offers better linearity and power efficiency than phase modulators based on multi-bit digital-to-time converters (DTCs). Therefore, the proposed approach enables simultaneous improvements in power efficiency and linearity. Fabricated in a 65-nm CMOS process, the proposed TX achieves a 33.5% peak power-added efficiency (PAE) at 24.2-dBm output power and supports wideband 50-MSymbol/s 256-quadratic-AM (QAM) signals without digital predistortion (DPD). A maximum system efficiency (SE) of 24.5% is achieved at −25.1-dB error vector magnitude (EVM), demonstrating superior performance compared to state-of-the-art DPD-less digital polar TXs.
1 January 2026 in IEEE Journal of Solid-State Circuits
3 March 2026 in IEEE Journal of Solid-State Circuits
This work presents a D-band high-power-density four-element phased-array transceiver for 6G user equipment (UE). Conventional designs require large multi-stage LO generation circuits for D-band up/down conversion, making it difficult to achieve compact size and low-power consumption. To address this, we propose an integrated LO chain using an injection-locked tripling phase shifter (ILTPS), which enables both frequency tripling and phase shifting within a single circuit without multi-stage amplifiers. The ILTPS achieves an area of 0.088 mm2 and a power consumption of 15 mW. In addition, to realize high power density, the transceiver integrates a bi-active sub-harmonic mixer (BA-SHM) and a D-band PA/LNA with PA-sharing TDD switching. An eight-element antenna-in-package (AiP) module using two transceiver ICs operates in the 142–164-GHz frequency range, achieving an EIRP of 25.7 dBm and a maximum data rate of 56 Gbps. The power consumption per element is 150 mW in TX mode and 93 mW in RX mode with 1 V VDD. The active area of this transceiver is 8.5 mm2, and it is implemented using a 65 nm CMOS process.
1 January 2026 in IEEE Journal of Solid-State Circuits
1 January 2026 in IEEE Solid-State Circuits Letters
3 February 2026 in IEEE Journal of Solid-State Circuits
This article presents a 300-GHz-band amplifier-last outphasing phased-array transmitter with path mismatch calibration in a 65-nm CMOS technology. Calibration is essential for mitigating impairments in outphasing systems used for wideband communication. The transmitter integrates two independent sub-THz LO generation chains to calibrate the phase mismatch between two paths and configure the phase delay between different phased-array elements. An integrated RF outphasing amplifier calibrates the amplitude mismatch and improves the transmitter’s effective isotropic radiated power (EIRP). After calibration, the transmitter exhibits a 3.3-dB improvement in error vector magnitude and supports 16 QAM modulation at 52 Gb/s over a distance of 9 cm. It achieves a peak EIRP of 8.9 dBm at 246 GHz, with a minimum EIRP of 5.0 dBm across the frequency range from 237 to 250 GHz. An 8×1 phased-array transmitter is implemented, demonstrating a main lobe scanning range of ±12° in the $E$ -plane.