The article is devoted to the construction of surrogate models as a tool for assessing the influence of the properties of materials of insulating structures and the defects present in them, the geometry of insulating structures, on the electrical strength in the area of the defect location. Using the example of a glass part of the PS-70E (U70) insulator, it is shown that a surrogate model in the form of a polynomial of four seventh-order variables, which takes into account changes in the dielectric permittivity and specific conductivities of the model materials, is sufficient to analyze the electrical strength in the area of the defect location when the properties of materials change. The relative error in determining the electric field based on the results of simulation modeling and calculation using the surrogate model is no more than 11.2% and 10.7% for the maximum and minimum electric field strengths in the defect, respectively. It is shown that the dielectric constant of the substance of the insulating structure has a significant effect on the field strength only when the permeability of the defect substance is less than 6, which is typical for defects in the form of gas inclusions. The change in the characteristics of the field in the defect, depending on the geometry of the structure, was also considered using the example of the head of the glass part of the PS-70E insulator. The change in geometry was studied at different values of the amplitudes of the first spatial harmonics of the forming boundaries with a simultaneous change in the location of the spherical defect inside the structure. It is shown that in this case, a polynomial of 5 degrees of 4 variables is sufficient to construct a surrogate model. The maximum margin of error is no more than 7.6%. The analysis of the dependences of the field strengths inside the defect in the considered surrogate models, as well as in the obtained model, suggests that defects in high-voltage insulators ranging in size from 0.1 to 2 mm can be considered potentially dangerous. Статья посвящена построению суррогатных моделей как инструменту оценки влияния свойств материалов изоляционных конструкций и присутствующих в них дефектов, геометрии изоляционных конструкций, на электрическую прочность в области расположения дефекта. На примере стеклянной детали изолятора ПС-70Е показано, что для анализа электрической прочности в области расположения дефекта при изменении свойств материалов достаточно суррогатной модели в виде полинома четырех переменных седьмого порядка, учитывающей изменение диэлектрических проницаемостей и удельных проводимостей материалов модели. Относительная ошибка в определении электрического поля по результатам имитационного моделирования и расчета по суррогатной модели составляет не более 11,2% и 10,7% для максимальной и минимальной напряженности электрического поля в дефекте соответственно. Показано, что диэлектрическая проницаемость вещества изоляционной конструкции оказывает существенное влияние на напряженность поля только при проницаемостях вещества дефекта, меньших 6, что характерно для дефектов в виде газовых включений. Изменение характеристик поля в дефекте в зависимости от геометрии конструкции рассматривалось также на примере головки стеклянной детали изолятора ПС-70Е. Изменение геометрии изучалось при различных значениях амплитуд первых пространственных гармоник образующих границ с одновременным изменением расположения сферического дефекта внутри конструкции. Показано, что для построения суррогатной модели в этом случае достаточно полинома 5 степени 4 переменных. Максимальная погрешность при этом составляет не более 7,6%. Анализ зависимостей напряженностей поля внутри дефекта в рассматриваемых суррогатных моделях, а также в полученной ранее модели, позволяет утверждать, что потенциально опасными могут считаться дефекты в высоковольтных изоляторах размерами от 0,1 до 2 мм.