Luiz Fernando Kultz. Unti

Luiz Fernando Kultz. Unti

Auto-generated profile, based on publicly available information

Luiz Fernando Kultz. Unti

Universidade Estadual de Campinas, Brasil

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2019 in Ceramics International
Verified
Journal Article
Closed access
LULuiz Fernando Kultz. Unti
Luiz Fernando Kultz. Unti
EGEdson Cezar Grzebielucka
Edson Cezar Grzebielucka
ACAdriana Scoton Antonio Chinelatto
Adriana Scoton Antonio Chinelatto
Glenn MatherGlenn Mather
Glenn Mather
ACAdilson Luiz Chinelatto
Adilson Luiz Chinelatto

20 November 2025 in Acta Materialia
Verified
Journal Article
Closed access
LUL.F. Kultz Unti
L.F. Kultz Unti
LALeonardo Shoji Aota
Leonardo Shoji Aota
ELE.S.N. Lopes
E.S.N. Lopes
GRG.G. Ribamar
G.G. Ribamar
NSN. Schell
N. Schell
KZK.D. Zilnyk
K.D. Zilnyk

1 January 2025 in Materials Research
Verified
Journal Article
Open access
PDF file
NRN. Rojas-Arias
N. Rojas-Arias
LUL.F.K. Unti
L.F.K. Unti
DVD.B. Valim
D.B. Valim
AGA.H.G. Gabriel
A.H.G. Gabriel
EFE.B. Fonseca
E.B. Fonseca
Eder Socrates Najar LopesEder Socrates Najar Lopes
Eder Socrates Najar Lopes
Laser-based powder bed fusion (PBF-LB) of AlSi10Mg alloys faces non-equilibrium solidification, resulting in a microstructure of α-aluminum phase matrix and an interconnected, fibrous α-silicon-rich phase network. The development of heat treatment (HT) routes tailored specifically for PBF-LB parts are essential, as standardized procedures may not yield optimal results. This study investigates the effect of different HTs on the microstructural characteristics and hardness of AlSi10Mg parts. Analyses revealed that the as-built (AB) microstructure exhibited a typical cellular-dendritic solidification structure. The eutectic α-Si-rich network partially degenerated after direct aging (DA) and stress relieving (SR), while solution annealing (SA), and solution annealing + aging HT erased the solidification microstructure, producing α-Si-rich precipitates dispersed within the α-Al matrix. Columnar grains exhibited preferential epitaxial growth along {001} planes in the direction, with no significant changes observed after HTs. The AB sample displayed a hardness of 122 HV, increasing up to 149 HV after DA. Conversely, SR and SA led to a hardness reduction between 61 and 77 HV. While the DA HT maintains the AB microstructural characteristics with a hardness increase, SR and SA HTs modify the solidification microstructure, reducing hardness.

1 January 2023 in Materials Research
Verified
Journal Article
Open access
PDF file
PRPedro Henrique Eça Rodrigues
Pedro Henrique Eça Rodrigues
LULuiz Fernando Kultz Unti
Luiz Fernando Kultz Unti
FMFábio Edson Mariani
Fábio Edson Mariani
PGPiter Gargarella
Piter Gargarella
OCOsvaldo Cintho
Osvaldo Cintho
KZKahl Zilnyk
Kahl Zilnyk
The objective of this work is to study the possibility of obtaining dense parts using water atomized AISI 316L steel powder in the L-PBF process. Despite its irregular, non-spherical, particle morphology, it has a significantly lower cost. 25 samples were produced varying the laser power and the scanning speeds to determine the optimal processing conditions. Additionally, hot isostatic pressing (HIP) was performed after the L-PBF process to further increase densification. Selected samples were subjected to microstructural characterization. The best densification results obtained were for the sample produced with the laser power of 173 W and scanning speed of 600 mm/s, where densifications close to 98% were obtained. HIP post-processing promoted increased densification of samples with closed porosity, allowing samples with densification above 95% to reach values close to 100%. HIP did not promote the closure of open pores. The results indicate that the use of water atomized AISI 316L in the L-PBF process combined with post-processing by HIP can produce dense engineering components and at the same time reduce the production costs of the manufactured components, mainly because it is a lower cost raw material when compared to the commonly used feedstock obtained by gas atomization.