19 May 2023 in Nature Communications
Controlling audible sound requires inherently broadband and subwavelength acoustic solutions, which are to date, crucially missing. This includes current noise absorption methods, such as porous materials or acoustic resonators, which are typically inefficient below 1 kHz, or fundamentally narrowband. Here, we solve this vexing issue by introducing the concept of plasmacoustic metalayers. We demonstrate that the dynamics of small layers of air plasma can be controlled to interact with sound in an ultrabroadband way and over deep-subwavelength distances. Exploiting the unique physics of plasmacoustic metalayers, we experimentally demonstrate perfect sound absorption and tunable acoustic reflection over two frequency decades, from several Hz to the kHz range, with transparent plasma layers of thicknesses down to λ/1000. Such bandwidth and compactness are required in a variety of applications, including noise control, audio-engineering, room acoustics, imaging and metamaterial design.
23 September 2020 in Journal of Physics D: Applied Physics
Conventional loudspeakers generate sound through the vibration of a diaphragm, attached to a rigid frame through elastic suspensions. Although such construction is satisfactory for sound diffusion in steady environments, it is likely to fail in harsh conditions, which is often the case for active noise control applications. Plasma-based actuators appear to be a promising alternative since they do not involve any fragile moving parts. In this paper, a positive corona discharge actuator in a wire-to-mesh geometry is proposed in the perspective of active noise control applications, as it is capable of generating sufficient sound pressure levels with limited signal distortion. The study introduces analytical and numerical models aiming at characterizing the sound field generated by the corona discharge actuator. The numerical simulation can facilitate the designing of such transducers. The acoustic power of the experimental prototype is increased through the optimization of emitter wires arrangement. The comparison of analytical model and numerical simulation with the experiment is presented. The analytical model successively describes the low frequency sound pressure field, while the numerical simulation is valid in the broader frequency range.
31 January 2022 in Acta Acustica
In the majority of active sound absorbing systems, a conventional electrodynamic loudspeaker is used as a controlled source. However, particular situations may require an actuator that is more resistant to harsh environments, adjustable in shape, and lighter. In this work, a plasma-based electroacoustic actuator operating on the atmospheric corona discharge principle is used to achieve sound absorption in real-time. Two control strategies are introduced and tested for both normal in the impedance tube and grazing incidence in the flow duct. The performance of plasma-based active absorber is competitive with conventional passive technologies in terms of effective absorption bandwidth and low-frequency operation, however, it presents some inherent limitations that are discussed. The study reveals that the corona discharge technology is suitable for active noise control in ducts while offering flexibility in design, compactness, and versatility of the absorption frequency range.
23 May 2019 in Water Resources Research
We conducted laboratory experiments to measure the sound produced during water‐by‐gas and kerosene‐by‐water displacements in samples of Indiana limestone and sandstones with different permeabilities. In water‐by‐gas displacement experiments, intensive sound was detected during the injection of hundreds of pore volumes and even when mobile water saturation was small (~1%). The sound was produced in a wide frequency range starting with frequencies less than 1 kHz; the upper frequencies varied from approximately 15 kHz for high‐permeability sandstone to almost 50 kHz for low‐permeability sandstone. In contrast to the experiments with gas flow through the dry rock samples, where sound appears only at high gas rates corresponding to the Forchheimer flow regime, the displacement produces sound at lower rates, corresponding to Darcy regime. Both the drop rate of sound emission and the sound intensity at the same mobile water saturation were determined to inversely depend on the rock permeability. We found that sound produced by sandstones shows a power law relationship between the number of events and their amplitudes, where the absolute value of the exponent also inversely depends on the rock permeability. In kerosene‐by‐water displacement experiments, the signal was observed at lower frequencies (up to 5 kHz) and only during injection of the first several pore volumes. A model describing the sound generation was suggested; the model considers acoustic events as a train of random pressure pulses corresponding to a Poisson point process. Simulation results demonstrated that the model reasonably reproduces the general trend of sound spectra produced by sandstones.