26 October 2021 in IEEE Electron Device Letters
The trade-off relationship between specific on-resistance and short-circuit withstand time in 1.2 kV 4H-SiC MOSFETs was drastically increased using a novel device structure. MOSFETs with deep P-well-formed using channeling implantation were firstly demonstrated to improve short-circuit ruggedness (~4 times longer than conventional MOSFET) with no negative impact on specific on-resistance. Proposed MOSFETs achieved short-circuit withstand time of $8~\mu \text{s}$ . Channeling implant with low energy was conducted to form deep P-well junctions. Fabrication of a deep P-well using channeling implantation is demonstrated using no additional nor complicated processes when compared to the conventional MOSFET fabrication process. A comparison between the conventional and novel designs was performed in terms of the output characteristics, blocking behaviors, and short-circuit ruggedness.
2 September 2021 in IEEE Journal of the Electron Devices Society
A detailed structural analysis of 1.2 kV 4H-SiC MOSFETs with accumulation mode channel is reported in this paper. 1.2 kV SiC MOSFETs with a variety of cell designs were fabricated and compared with respect to the output and transfer characteristics, and blocking behaviors. All the design rules, such as channel length, JFET width, contact openings, gate-to-source overlap, and cell pitch were investigated to clearly provide the quantitative impact on the static performances. 2D-simulation was also conducted to support experimental results. As a result, it turned out that the channel length is the most determining factor for the specific on-resistance, resulting in 0.364 $\text{m}\Omega $ -cm 2 increase per $0.1~ {\mu }\text{m}$ increase in the channel length. However, the channel potential is also largely dependent on the channel length such that the leakage current tends to increase with short channel design. The enhanced doping in the JFET region with a current spreading layer (CSL) is essential for achieving a narrower JFET width, which satisfies all static performances, as well as device reliability and ruggedness. Methods to further improve the trade-off characteristics using other design aspects are discussed in this paper.
24 March 2022 in IEEE Electron Device Letters
This letter reports the demonstration of 1.2 kV 4H-SiC Schottky-integrated MOSFETs (JBSFETs) achieving the same specific on-resistance as the pure MOSFET by using an innovative layout approach as well as novel deep P-well structure. The proposed JBSFET significantly reduces the specific on-resistance accomplishing 2x reduction in the chip size, when compared with the traditional, chip-to-chip parallel connection of separate MOSFET and JBS diode. Moreover, the leakage current originated from the Schottky contact was successfully suppressed by adopting a $1.8~\mu \text{m}$ deep P-well structure implemented by channeling implantation. Device design strategy with layout approach, fabrication, and static and short-circuit characteristics are discussed in this letter. In order to understand and clarify the experimental results, 2D simulations were conducted.
2 November 2022 in IEEE Journal of the Electron Devices Society
1.2kV 4H-SiC MOSFETs with different junction depths of JFET and P-well regions were fabricated. For each JFET/P-well depth combination, channel lengths and JFET widths were also varied to compare specific on-resistance, breakdown voltage, and short-circuit withstand time. It was discovered that deep JFET structure provides low specific on-resistance (12% lower) with high breakdown voltage. On the other hand, MOSFETs with deep P-well result in high breakdown voltage with low leakage current even in shorter channel length (0.4 lm). Moreover, trade-off relationship between Ron,sp and short-circuit withstand time is discussed for MOSFETs with different JFET widths and channel lengths; the deep JFET implant provides better trade-off relationship due to the feasibility of narrow JFET width. For the further improvement of trade-off relationship, MOSFETs with deep JFET and P-well implant are proposed. Lastly, the importance of high channel mobility for not only static characteristics but also short-circuit characteristics was investigated. The in-depth understanding of measured electrical characteristics was supported by 2D-device simulations.
18 April 2023 in IEEE Electron Device Letters
This letter presents a study on improving the reverse characteristics of 1.2 kV 4H-SiC JBS diodes by employing a deep P+ grid structure. To achieve a deep junction with low implantation energy, channeling implantation was implemented. Diodes with different junction depths of the P+ grid were fabricated to compare the forward and reverse I-V characteristics; depth of $0.8~ \mu \text{m}$ , $1.4~ \mu \text{m}$ , and $2.2~ \mu \text{m}$ . Almost identical forward I-V characteristics were achieved regardless of the P+ grid depth. However, the leakage current was significantly suppressed by the deeper P+ grid junction depth; $60~ \mu \text{A}$ , $1.5~ \mu \text{A}$ , and 1.7 nA (at 1200V for 0.8, 1.4, $2.2~ \mu \text{m}$ deep P+ grids, respectively). Although the deep junction was implemented with channeling implantation, high breakdown voltages similar to that of the shallow junction are achieved in the proposed JBS diode. This is due to the relatively low doping concentration in the deep junction. Moreover, the edge termination structures with different main junction depths were discussed. For a near ideal breakdown voltage insensitive to the JTE dose, Hybrid-JTE was employed. It was demonstrated that the high breakdown voltage with the drastically reduced leakage current of the proposed JBS diodes, was achieved using identical edge termination technology to the conventional shallow junction. To better understand the effect of the deep junction, 2D simulation was conducted.
17 October 2024 in IEEE Transactions on Electron Devices
This article reports an investigation into the impact of P $^{+}$ body design in 4H-silicon carbide (SiC) MOSFETs. Specifically, 1.2 kV SiC MOSFETs with various P $^{+}$ body designs were fabricated and analyzed. MOSFETs with stripe pattern P $^{+}$ body, orthogonal P $^{+}$ body, and without P $^{+}$ body were fabricated on the same wafer using the same mask set. A comprehensive comparison was conducted among the MOSFETs with different P $^{+}$ body designs, focusing on their static characteristics, switching characteristics, and avalanche ruggedness. Two-dimensional simulations were also performed to support experimental results. The orthogonal P $^{+}$ design was observed to provide improved conduction behaviors without adversely affecting the static characteristics, thanks to the reduced cell pitch. Conversely, MOSFETs without a P $^{+}$ body exhibited reduced breakdown voltage due to the inability to extract holes during avalanche conditions. The presence of a large area of P $^{+}$ body contact enhances the switching characteristics, whereas MOSFETs with a small area of P $^{+}$ body contact exhibit a slow change of potential within the p-well during switching. Additionally, similar results are observed in unclamped inductive switching (UIS). The small area of P $^{+}$ body contact causes a slow change of potential in the channel region during avalanche conditions. Consequently, the channel potential decreases, leading to higher avalanche current flow from the channel and a reduction in avalanche energy.