13-kV 4H-SiC MOSFETs were successfully fabricated on a 125-μm-thick epitaxial layer on 6-in, N+ SiC substrates. Both lateral and longitudinal straggles from the P-well implant were investigated to optimize the JFET width and thus to avoid channel pinching in the JFET region. Channel lengths and channel mobilities were varied to investigate the effect of channel portions in determining the on-state resistance of the 13-kV MOSFETs. It was discovered that the low channel mobility limits the transconductance, such that the MOSFETs cannot offer full current at reasonable gate voltages (Vgs = ~ 20 V). Even in high voltage MOSFETs, it is essential to have a reasonably high channel mobility to reduce on-state power loss. Therefore, channel design and process are also important aspects of high voltage devices. A superior blocking capability of 13.2 kV was demonstrated using a ring-based edge termination structure. It is important to note that the straggling effect due to ion implantations should also be taken into account when designing an edge termination structure. Static electrical characteristics, scanning electron microscope (SEM) imaging, secondary ion mass spectrometry (SIMS) analysis, and 2-D simulation of the 13-kV MOSFETs were employed to support this reasoning.
2 September 2021 in IEEE Journal of the Electron Devices Society
A detailed structural analysis of 1.2 kV 4H-SiC MOSFETs with accumulation mode channel is reported in this paper. 1.2 kV SiC MOSFETs with a variety of cell designs were fabricated and compared with respect to the output and transfer characteristics, and blocking behaviors. All the design rules, such as channel length, JFET width, contact openings, gate-to-source overlap, and cell pitch were investigated to clearly provide the quantitative impact on the static performances. 2D-simulation was also conducted to support experimental results. As a result, it turned out that the channel length is the most determining factor for the specific on-resistance, resulting in 0.364 $\text{m}\Omega $ -cm 2 increase per $0.1~ {\mu }\text{m}$ increase in the channel length. However, the channel potential is also largely dependent on the channel length such that the leakage current tends to increase with short channel design. The enhanced doping in the JFET region with a current spreading layer (CSL) is essential for achieving a narrower JFET width, which satisfies all static performances, as well as device reliability and ruggedness. Methods to further improve the trade-off characteristics using other design aspects are discussed in this paper.
This letter reports the demonstration of 1.2 kV 4H-SiC Schottky-integrated MOSFETs (JBSFETs) achieving the same specific on-resistance as the pure MOSFET by using an innovative layout approach as well as novel deep P-well structure. The proposed JBSFET significantly reduces the specific on-resistance accomplishing 2x reduction in the chip size, when compared with the traditional, chip-to-chip parallel connection of separate MOSFET and JBS diode. Moreover, the leakage current originated from the Schottky contact was successfully suppressed by adopting a $1.8~\mu \text{m}$ deep P-well structure implemented by channeling implantation. Device design strategy with layout approach, fabrication, and static and short-circuit characteristics are discussed in this letter. In order to understand and clarify the experimental results, 2D simulations were conducted.
2 November 2022 in IEEE Journal of the Electron Devices Society
1.2kV 4H-SiC MOSFETs with different junction depths of JFET and P-well regions were fabricated. For each JFET/P-well depth combination, channel lengths and JFET widths were also varied to compare specific on-resistance, breakdown voltage, and short-circuit withstand time. It was discovered that deep JFET structure provides low specific on-resistance (12% lower) with high breakdown voltage. On the other hand, MOSFETs with deep P-well result in high breakdown voltage with low leakage current even in shorter channel length (0.4 lm). Moreover, trade-off relationship between Ron,sp and short-circuit withstand time is discussed for MOSFETs with different JFET widths and channel lengths; the deep JFET implant provides better trade-off relationship due to the feasibility of narrow JFET width. For the further improvement of trade-off relationship, MOSFETs with deep JFET and P-well implant are proposed. Lastly, the importance of high channel mobility for not only static characteristics but also short-circuit characteristics was investigated. The in-depth understanding of measured electrical characteristics was supported by 2D-device simulations.
22 March 2024 in IEEE Transactions on Components, Packaging and Manufacturing Technology
To tackle the insulation challenges present in packaging medium-voltage silicon carbide power devices, we developed a package design for a 20-kV silicon carbide diode. This design incorporates a nonlinear resistive polymer-nanoparticle composite to boost insulation without compromising thermal performance. Employing a "sandwich" structure, where diodes are connected between direct-bonded copper substrates, our approach minimizes parasitic inductance (<4.5 nH) through a wire-bond-less design. According to thermal simulations, this configuration leads to a junction temperature reduction up to 53.5 oC. The submodule configuration not only cuts the total deformation by a factor of three but also enhances both reliability and manufacturability. By coating the electrode triple points with the resistive composite, electric field stress is diminished. Experimental tests indicated a 96% rise in the partial discharge inception voltage of substrates, increasing from 15.6 kV to 30.6 kV. For validation, scaled-down packages equipped with silicon carbide diodes exceeding 16 kV were fabricated and put through rigorous testing.
21 August 2024 in IEEE Transactions on Power Electronics
Bond wire lift-off is one of the main failure mechanisms for silicon carbide mosfet s. This occurs when the metallurgical weld between the bond-wire and the device source breaks creating an open circuit. The higher current on the remaining wires subjects them to additional thermal stress creating a positive feedback loop that can quickly lead to device failure if left unchecked. By detecting lift-off events during power converter operation damaged devices can be de-rated and equipment operators can be alerted to replace the power module before a failure occurs. This article presents an online, in situ monitoring circuit that can detect the incremental change in on-state inductance ( ${L_{\text{ds}}}$ ) caused by the redistribution of bond-wire current after a lift-off occurs. Unlike on-state resistance ( ${R_{\text{ds}}}$ ), the inductance does not depend on temperature, gate-oxide health, or gate-bias level. In addition, since the inductive impedance is frequency dependent, any bias related to converter operation can be suppressed by increasing the measurement frequency well above the switching frequency. Experimental results show that the proposed circuit can accurately measure inductive changes down to 10 pH, providing sufficient sensitivity to detect single wire lift-off events in test devices.