Currently, the world’s only source of low-energy antiprotons is the AD/ELENA facility located at CERN. To date, all precision measurements on single antiprotons have been conducted at this facility and provide stringent tests of fundamental interactions and their symmetries. However, magnetic field fluctuations from the facility operation limit the precision of upcoming measurements. To overcome this limitation, we have designed the transportable antiproton trap system BASE-STEP to relocate antiprotons to laboratories with a calm magnetic environment. We anticipate that the transportable antiproton trap will facilitate enhanced tests of charge, parity, and time-reversal invariance with antiprotons and provide new experimental possibilities of using transported antiprotons and other accelerator-produced exotic ions. We present here the technical design of the transportable trap system. This includes the transportable superconducting magnet, the cryogenic inlay consisting of the trap stack and detection systems, and the differential pumping section to suppress the residual gas flow into the cryogenic trap chamber.
8 May 2023 in IEEE Transactions on Applied Superconductivity
The MADMAX project aims at detecting axion dark matter in the mass range of 100 μeV. To facilitate axion to photon conversion with detectable rate a superconducting dipole magnet with a large bore is needed. The MADMAX dipole magnet has to generate ∼9 T in a 1.35 m aperture over ∼1.3 m in length. A key challenge for a magnet made of a cable in-conduit conductor (CICC), operating at 1.8 K with an indirect bath cooling is the quench detection. In order to validate feasibility, a mock-up coil with a quench behavior scalable to MADMAX was designed and produced. The paper gives an overview of the technical details of the MACQU test coil. The conductor, the magnet, the busbar and the supporting and cryogenic systems were designed at CEA. The cable was manufactured in China at the Chang Tong INC from WST Nb-Ti strands, the insertion and compaction was achieved in the ASIPP institute with a copper profile from Aurubis. The winding of the coil and the busbar pre-forming were performed at Bilfinger Noell as well as the assembly of the supporting structure and the thermal shield. The magnet was integrated in the JT60 test station at CEA Saclay and extensively tested. The magnet current reached 80% on the loadline instead of 90% as expected at nominal. The limitation is likely coming from uneven current distribution at the extremity of the magnet at the connection box location. Nevertheless, quench tests were successfully performed at constant currents from 10 kA to 17 kA. They proved that the initial quench velocities are of the order of 1 m/s to 10 m/s, high enough to safely detect a voltage drop in MADMAX and discharge the magnet. In addition, a thermo-hydraulic quench back effect was observed in the MACQU coil cooled by superfluid helium.
18 April 2024 in IEEE Transactions on Applied Superconductivity
Superconducting undulators constitute an important element of the European XFEL facility development program. The application of SCU technology at European XFEL paves the way to potentially enable lasing above 50 keV, opening new frontiers in scientific research and offering unprecedented capabilities in high-energy applications. A total of six modules are foreseen. The Superconducting undulator PRE-SerieS mOdule (S-PRESSO) is the preseries module for the free-electron laser superconducting undulator afterburner. This article presents a comprehensive assessment of the S-PRESSO superconducting undulator mock-up's magnetic performance conducted at the Institute for Beam Physics and Technology of the Karlsruhe Institute of Technology. After a description of the experimental setup and the coil, the results of training and of the magnetic field measurements are presented. The results demonstrate a robust design of the mock-up, which achieved the short sample limit, a long lasting stability at nominal current tested for 8 h, and a straight trajectory below European XFEL requirements. The measured quality of the magnetic field is studied and compared with simulations using the geometric values measured at room temperature with a coordinate measuring machine. This analysis suggests areas for potential improvement in the manufacturing process.
The High energy Engineering X-ray (HEX) diffraction beamline at the National Synchrotron Light Source II (NSLS-II) at Brookhaven National Lab (BNL) is the first high-energy beamline capable of reaching 200 keV for a monochromatic beam. With the 3 GeV electron beam energy for the NSLS-II ring, only the superconducting wiggler (SCW) producing greater than 4 T peak field can cover these ranges with a sufficient number of photons. The 1.2 m-long HEX-SCW has a period length of 70 mm and a field strength on-axis of 4.3 T. It utilizes no liquid helium, and the vertical aperture size of the electron beam vacuum chamber is 8 mm. Unlike regular undulators/wigglers, there is no standard configuration for the magnetic measurement system for superconducting insertion devices. The NSLS-II Insertion Devices group has developed, in collaboration with the vacuum group, a novel in-vacuum Hall mapper with a 1.75 m in-vacuum linear motor and an in-vacuum flip coil system utilizing many commercial-off-the-shelf products. The measurements were conducted at the BNL, and the device was installed in the ring and commissioned. This paper provides a description of the SCW and its magnetic measurement systems, as well as a brief account of the installation and commissioning efforts.
High temperature superconducting (HTS) power cables can provide electric utilities with a new way to solve power distribution issues in densely populated urban areas. Compared to conventional cable technologies, based on copper or aluminum, HTS cables can either carry several times more power at the same voltage due to the huge current transport capacity of HTS materials which is more than 150 times that of copper, or carry the same amount of power at a lower voltage level. As long as the current carried by the cable is below the so-called critical current of the cable, HTS cables exhibit no ohmic power loss for direct currents and just very small losses for alternating currents (AC). High temperature superconductor materials typically used in cables are tapes with critical current densities of > 100 A/mm 2 when cooled in liquid nitrogen. Consequently, cables made of these conductors can carry large currents within very small dimensions. In addition, HTS cables are especially suited for densely-populated areas as they do not exhibit any electromagnetic or thermal impact on the environment, and only require a very narrow right-of-way, basically limited to the cable itself.